main
Ray Publish 0.1.0 b09ff4b

S25FL128SAGNFV010

Cypress Semicon · Pre-ordered Products · WSON-8(6x8)

S25FL128SAGNFV010 from Cypress Semicon, in a WSON-8(6x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CS# input Chip Select input that frames each SPI command; the interface is in standby when CS# is high.
2 SO/IO1 bidirectional Serial data output in single-bit mode and IO1 in dual/quad modes.
3 WP#/IO2 bidirectional Write Protect input (relevant only during WRR instruction cycles) or IO2 in quad mode.
4 VSS power_in Common supply and signal ground reference for the device core, input receivers and output drivers.
5 SI/IO0 bidirectional Serial data input in single-bit mode and IO0 in dual/quad modes.
6 SCK input Serial clock input for the SPI interface.
7 HOLD#/IO3 bidirectional HOLD# input pauses a command when low (internal pull-up) when Quad mode is disabled, or IO3 when Quad mode is enabled.
8 VCC power_in Core voltage supply for all internal functions, 2.7V to 3.6V; VIO and RESET# are tied to VCC inside this package.
9 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Cypress Semicon
Package WSON-8(6x8)
Category Electronic Tools/Instruments/Consumables
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Core supply voltage VCC 2.7 3.6 V 33
Ambient temperature, Automotive In-Cabin TA -40 105 °C Automotive (A) In-Cabin 33
Storage temperature -65 150 °C Plastic packages 33
Ambient temperature with power applied -65 125 °C 33
VCC absolute maximum VCC -0.5 4 V 33
VIO absolute maximum VIO -0.5 4 V VIO must be <= VCC + 200 mV 33
Input voltage with respect to VSS -0.5 V max is VIO + 0.5V 33
Output short circuit current 100 mA One output at a time, not longer than one second 33
Input low voltage VIL -0.5 V max is 0.2 x VIO 36
Input leakage current ILI -2 2 µA VCC = VCC Max, VIN = VIH or VIL 36
Output leakage current ILO -2 2 µA VCC = VCC Max, VIN = VIH or VIL 36
Active supply current (READ) Serial SDR@50 MHz ICC1 22 mA Outputs unconnected during read data return; 16/22 printed, 22 taken for automotive 36
Active supply current (READ) Serial SDR@133 MHz ICC1 35 mA Outputs unconnected during read data return; 33/35 printed, 35 taken for automotive 36
Active supply current (READ) Quad SDR@80 MHz ICC1 50 mA Outputs unconnected during read data return 36
Active supply current (READ) Quad SDR@104 MHz ICC1 61 mA Outputs unconnected during read data return 36
Active supply current (Page Program) ICC2 100 mA CS# = VIO 36
Active supply current (WRR) ICC3 100 mA CS# = VIO 36
Active supply current (SE) ICC4 100 mA CS# = VIO 36
Active supply current (BE) ICC5 100 mA CS# = VIO 36
Standby current (Automotive) ISB 70 300 µA RESET#, CS# = VIO; SI, SCK = VIO or VSS, Automotive Temp 36
Input capacitance CIN 8 pF 1 MHz; applies to SCK, CS#, RESET# 38
Output capacitance COUT 8 pF 1 MHz; applies to all I/O 38
VCC (min) to Read Operation tPU 300 µs 35
VCC (low) time tPD 1 µs 35
SCK clock frequency for READ and 4READ FSCK, R 50 MHz VIO = VCC 2.7V to 3.6V; min DC 40
SCK clock frequency for single commands FSCK, C 133 MHz Regulated VCC 3.0-3.6V, CL = 15 pF; min DC 40
SCK clock frequency for dual and quad commands FSCK, C 104 MHz DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR; min DC 40
SCK clock frequency for QPP, 4QPP FSCK, QPP 80 MHz min DC 40
CS# high time (read instructions) tCS 10 ns 40
CS# high time (program/erase) tCS 50 ns 40
CS# active setup time tCSS 3 ns relative to SCK 40
CS# active hold time tCSH 3 3000 ns relative to SCK; max only during Program/Erase Suspend/Resume 40
Data in setup time tSU 2 ns 40
Data in hold time tHD 2 ns 40
Clock low to output valid tV 6.5 ns Regulated VCC 3.0-3.6V, CL = 15 pF (8.0 at 2.7-3.6V CL=30 pF; 7.65 at 3.0-3.6V CL=30 pF) 40
Output hold time tHO 2 ns 40
Output disable time tDIS 0 8 ns 40
WP# setup time tWPS 20 ns Only for WRR when SRWD = 1 40
WP# hold time tWPH 100 ns Only for WRR when SRWD = 1 40
HOLD# active setup time tHLCH 3 ns relative to SCK 40
HOLD# active hold time tCHHH 3 ns relative to SCK 40
HOLD# non active setup time tHHCH 3 ns relative to SCK 40
HOLD# non active hold time tCHHL 3 ns relative to SCK 40
HOLD# enable to output invalid tHZ 8 ns 40
HOLD# disable to output valid tLZ 8 ns 40

CAD (KiCad official)

  • Symbol: S25FL128SAGNFV010
  • Footprint: Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm
  • 3D model: WSON-8(6x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: s25fl128sagnfv010-etched.step / s25fl128sagnfv010-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); s25fl128sagnfv010.step / s25fl128sagnfv010.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Cypress Semicon datasheet (154 pp, sha256 0ba64c6fde4ef734, retrieved 2026-11-02, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF