Generated by kicad-footprint-generator · KiCad file format 20260206
S25FL128SAGNFV010
Cypress Semicon · Pre-ordered Products · WSON-8(6x8)
S25FL128SAGNFV010 from Cypress Semicon, in a WSON-8(6x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS# | input | Chip Select input that frames each SPI command; the interface is in standby when CS# is high. |
| 2 | SO/IO1 | bidirectional | Serial data output in single-bit mode and IO1 in dual/quad modes. |
| 3 | WP#/IO2 | bidirectional | Write Protect input (relevant only during WRR instruction cycles) or IO2 in quad mode. |
| 4 | VSS | power_in | Common supply and signal ground reference for the device core, input receivers and output drivers. |
| 5 | SI/IO0 | bidirectional | Serial data input in single-bit mode and IO0 in dual/quad modes. |
| 6 | SCK | input | Serial clock input for the SPI interface. |
| 7 | HOLD#/IO3 | bidirectional | HOLD# input pauses a command when low (internal pull-up) when Quad mode is disabled, or IO3 when Quad mode is enabled. |
| 8 | VCC | power_in | Core voltage supply for all internal functions, 2.7V to 3.6V; VIO and RESET# are tied to VCC inside this package. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cypress Semicon |
| Package | WSON-8(6x8) |
| Category | Electronic Tools/Instruments/Consumables |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Core supply voltage | VCC | 2.7 | 3.6 | V | 33 | ||
| Ambient temperature, Automotive In-Cabin | TA | -40 | 105 | °C | Automotive (A) In-Cabin | 33 | |
| Storage temperature | -65 | 150 | °C | Plastic packages | 33 | ||
| Ambient temperature with power applied | -65 | 125 | °C | 33 | |||
| VCC absolute maximum | VCC | -0.5 | 4 | V | 33 | ||
| VIO absolute maximum | VIO | -0.5 | 4 | V | VIO must be <= VCC + 200 mV | 33 | |
| Input voltage with respect to VSS | -0.5 | V | max is VIO + 0.5V | 33 | |||
| Output short circuit current | 100 | mA | One output at a time, not longer than one second | 33 | |||
| Input low voltage | VIL | -0.5 | V | max is 0.2 x VIO | 36 | ||
| Input leakage current | ILI | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 36 | |
| Output leakage current | ILO | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 36 | |
| Active supply current (READ) Serial SDR@50 MHz | ICC1 | 22 | mA | Outputs unconnected during read data return; 16/22 printed, 22 taken for automotive | 36 | ||
| Active supply current (READ) Serial SDR@133 MHz | ICC1 | 35 | mA | Outputs unconnected during read data return; 33/35 printed, 35 taken for automotive | 36 | ||
| Active supply current (READ) Quad SDR@80 MHz | ICC1 | 50 | mA | Outputs unconnected during read data return | 36 | ||
| Active supply current (READ) Quad SDR@104 MHz | ICC1 | 61 | mA | Outputs unconnected during read data return | 36 | ||
| Active supply current (Page Program) | ICC2 | 100 | mA | CS# = VIO | 36 | ||
| Active supply current (WRR) | ICC3 | 100 | mA | CS# = VIO | 36 | ||
| Active supply current (SE) | ICC4 | 100 | mA | CS# = VIO | 36 | ||
| Active supply current (BE) | ICC5 | 100 | mA | CS# = VIO | 36 | ||
| Standby current (Automotive) | ISB | 70 | 300 | µA | RESET#, CS# = VIO; SI, SCK = VIO or VSS, Automotive Temp | 36 | |
| Input capacitance | CIN | 8 | pF | 1 MHz; applies to SCK, CS#, RESET# | 38 | ||
| Output capacitance | COUT | 8 | pF | 1 MHz; applies to all I/O | 38 | ||
| VCC (min) to Read Operation | tPU | 300 | µs | 35 | |||
| VCC (low) time | tPD | 1 | µs | 35 | |||
| SCK clock frequency for READ and 4READ | FSCK, R | 50 | MHz | VIO = VCC 2.7V to 3.6V; min DC | 40 | ||
| SCK clock frequency for single commands | FSCK, C | 133 | MHz | Regulated VCC 3.0-3.6V, CL = 15 pF; min DC | 40 | ||
| SCK clock frequency for dual and quad commands | FSCK, C | 104 | MHz | DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR; min DC | 40 | ||
| SCK clock frequency for QPP, 4QPP | FSCK, QPP | 80 | MHz | min DC | 40 | ||
| CS# high time (read instructions) | tCS | 10 | ns | 40 | |||
| CS# high time (program/erase) | tCS | 50 | ns | 40 | |||
| CS# active setup time | tCSS | 3 | ns | relative to SCK | 40 | ||
| CS# active hold time | tCSH | 3 | 3000 | ns | relative to SCK; max only during Program/Erase Suspend/Resume | 40 | |
| Data in setup time | tSU | 2 | ns | 40 | |||
| Data in hold time | tHD | 2 | ns | 40 | |||
| Clock low to output valid | tV | 6.5 | ns | Regulated VCC 3.0-3.6V, CL = 15 pF (8.0 at 2.7-3.6V CL=30 pF; 7.65 at 3.0-3.6V CL=30 pF) | 40 | ||
| Output hold time | tHO | 2 | ns | 40 | |||
| Output disable time | tDIS | 0 | 8 | ns | 40 | ||
| WP# setup time | tWPS | 20 | ns | Only for WRR when SRWD = 1 | 40 | ||
| WP# hold time | tWPH | 100 | ns | Only for WRR when SRWD = 1 | 40 | ||
| HOLD# active setup time | tHLCH | 3 | ns | relative to SCK | 40 | ||
| HOLD# active hold time | tCHHH | 3 | ns | relative to SCK | 40 | ||
| HOLD# non active setup time | tHHCH | 3 | ns | relative to SCK | 40 | ||
| HOLD# non active hold time | tCHHL | 3 | ns | relative to SCK | 40 | ||
| HOLD# enable to output invalid | tHZ | 8 | ns | 40 | |||
| HOLD# disable to output valid | tLZ | 8 | ns | 40 |
CAD (KiCad official)
- Symbol:
S25FL128SAGNFV010 - Footprint:
Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm - 3D model: WSON-8(6x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
s25fl128sagnfv010-etched.step/s25fl128sagnfv010-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);s25fl128sagnfv010.step/s25fl128sagnfv010.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Cypress Semicon datasheet (154 pp, sha256
0ba64c6fde4ef734, retrieved 2026-11-02, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).