main
Ray Publish 0.1.0 191c721

S25FL128SAGNFV000

Infineon Technologies · NOR FLASH · WDFN-8-EP

S25FL128SAGNFV000 from Infineon Technologies, in a WDFN-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CS# input Chip Select: active LOW enables the device; when HIGH the device is deselected, inputs are ignored and outputs are high impedance.
2 SO/IO1 bidirectional Serial Output for single-bit commands (data shifted out on falling edge of SCK) and IO1 for Dual or Quad commands.
3 WP#/IO2 bidirectional Write Protect when not in Quad mode and IO2 in Quad mode; has an internal pull-up and may be left unconnected if not used for Quad commands.
4 VSS power_in Supply and signal ground reference for the device core, input receivers and output drivers.
5 SI/IO0 bidirectional Serial Input for instructions, addresses and data (latched on rising edge of SCK), and IO0 for Dual or Quad commands.
6 SCK input Serial Clock: synchronization reference for the SPI interface; inputs are latched on the rising edge, SDR outputs change after the falling edge.
7 HOLD#/IO3 bidirectional Hold (pause) serial transfer in single-bit or Dual commands and IO3 in Quad mode; has an internal pull-up and may be left unconnected if not used for Quad commands.
8 VCC power_in Core power supply for all internal logic, read, program and erase, 2.7 V to 3.6 V.
9 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Infineon Technologies
Package WDFN-8-EP
Category Memory
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Storage temperature, plastic packages -65 150 °C 31
Ambient temperature with power applied -65 125 °C 31
Core supply voltage VCC -0.5 4 V 31
I/O supply voltage VIO -0.5 4 V VIO must always be less than or equal VCC + 200 mV 31
Output short circuit current 100 mA No more than one output shorted to ground at a time, not longer than one second 31
Core supply voltage VCC 2.7 3.6 V 32
I/O supply voltage VIO 1.65 V 1.65 V to VCC + 200 mV 32
Ambient temperature, Industrial Plus (V) TA -40 105 °C Industrial Plus (V) 32
Input high voltage VIH 0.7 x VIO -40°C to +105°C 35
Input low voltage VIL 0.2 x VIO -40°C to +105°C 35
Output low voltage VOL 0.15 x VIO IOL = 1.6 mA, VCC = VCC min 35
Output high voltage VOH 0.85 x VIO IOH = -0.1 mA 35
Input leakage current ILI -2 2 µA VCC = VCC Max, VIN = VIH or VIL 35
Output leakage current ILO -2 2 µA VCC = VCC Max, VIN = VIH or VIL 35
Active supply current (READ), Serial SDR at 50 MHz ICC1 22 mA Outputs unconnected during read data return 35
Active supply current (READ), Serial SDR at 133 MHz ICC1 35 mA Outputs unconnected during read data return 35
Active supply current (READ), Quad SDR at 80 MHz ICC1 50 mA Outputs unconnected during read data return 35
Active supply current (READ), Quad SDR at 104 MHz ICC1 61 mA Outputs unconnected during read data return 35
Active supply current (READ), Quad DDR at 66 MHz ICC1 75 mA Outputs unconnected during read data return 35
Active supply current (READ), Quad DDR at 80 MHz ICC1 90 mA Outputs unconnected during read data return 35
Active supply current (Page program) ICC2 100 mA CS# = VIO 35
Active supply current (WRR) ICC3 100 mA CS# = VIO 35
Active supply current (SE) ICC4 100 mA CS# = VIO 35
Active supply current (BE) ICC5 100 mA CS# = VIO 35
Standby current ISB 70 300 µA RESET#, CS# = VIO; SI, SCK = VIO or VSS 35
VCC minimum operation voltage VCC (min) 2.7 V 33
VCC cut-off where re-initialization is needed VCC (cut-off) 2.4 V 33
VCC low voltage for initialization to occur VCC (low) 1.6 V 33
VCC (min) to read operation tPU 300 µs 33
VCC (low) time tPD 15 µs 33
Input capacitance (SCK, CS#, RESET#) CIN 8 pF 1 MHz 38
Output capacitance (all I/O) COUT 8 pF 1 MHz 38
Thermal resistance junction to ambient Theta JA 28 °C/W 128 Mb, WNG008, EIA/JESD51, still air (0 m/s) 31
Thermal resistance junction to board Theta JB 7.8 °C/W 128 Mb, WNG008 31
Thermal resistance junction to case Theta JC 12.6 °C/W 128 Mb, WNG008 31
Reset setup tRS 50 ns Prior reset end and RESET# HIGH before RESET# LOW 39
Reset pulse hold tRPH 35 µs RESET# LOW to CS# LOW 39
RESET# pulse width tRP 200 ns 39
Reset hold tRH 50 ns RESET# HIGH before CS# LOW 39
SCK clock frequency for READ and 4READ FSCK, R 0 50 MHz VIO = VCC 2.7 V to 3.6 V; min printed as DC 40
SCK clock frequency for single commands FSCK, C 0 133 MHz VIO = VCC 2.7 V to 3.6 V; min printed as DC 40
SCK clock frequency for DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR FSCK, C 0 104 MHz VIO = VCC 2.7 V to 3.6 V; min printed as DC 40
SCK clock frequency for QPP, 4QPP FSCK, QPP 0 80 MHz VIO = VCC 2.7 V to 3.6 V; min printed as DC 40
CS# high time (Read instructions) tCS 10 ns VIO = VCC 2.7 V to 3.6 V 40
CS# high time (Program/erase) tCS 50 ns VIO = VCC 2.7 V to 3.6 V 40
Data in setup time tSU 1.5 3000 ns Max only applies during Program/Erase Suspend/Resume commands 40
Data in hold time tHD 2 ns VIO = VCC 2.7 V to 3.6 V 40
Clock low to output valid tV 8 ns Full VCC range (2.7-3.6 V) and CL = 30 pF 40
Output disable time tDIS 0 8 ns VIO = VCC 2.7 V to 3.6 V 40

CAD (KiCad official)

  • Symbol: S25FL128SAGNFV000
  • Footprint: Package_DFN_QFN:WDFN-8-1EP_8x6mm_P1.27mm_EP6x4.8mm
  • 3D model: WDFN-8-EP, generated on the KiCad land (body 8 x 6 mm, terminals on the pads, 0.75 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: s25fl128sagnfv000-etched.step / s25fl128sagnfv000-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); s25fl128sagnfv000.step / s25fl128sagnfv000.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Infineon Technologies datasheet (165 pp, sha256 e8827e742d791a99, retrieved 2026-11-17, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text+vision), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF