3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownS25FL128SAGNFV000
Infineon Technologies · NOR FLASH · WDFN-8-EP
S25FL128SAGNFV000 from Infineon Technologies, in a WDFN-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS# | input | Chip Select: active LOW enables the device; when HIGH the device is deselected, inputs are ignored and outputs are high impedance. |
| 2 | SO/IO1 | bidirectional | Serial Output for single-bit commands (data shifted out on falling edge of SCK) and IO1 for Dual or Quad commands. |
| 3 | WP#/IO2 | bidirectional | Write Protect when not in Quad mode and IO2 in Quad mode; has an internal pull-up and may be left unconnected if not used for Quad commands. |
| 4 | VSS | power_in | Supply and signal ground reference for the device core, input receivers and output drivers. |
| 5 | SI/IO0 | bidirectional | Serial Input for instructions, addresses and data (latched on rising edge of SCK), and IO0 for Dual or Quad commands. |
| 6 | SCK | input | Serial Clock: synchronization reference for the SPI interface; inputs are latched on the rising edge, SDR outputs change after the falling edge. |
| 7 | HOLD#/IO3 | bidirectional | Hold (pause) serial transfer in single-bit or Dual commands and IO3 in Quad mode; has an internal pull-up and may be left unconnected if not used for Quad commands. |
| 8 | VCC | power_in | Core power supply for all internal logic, read, program and erase, 2.7 V to 3.6 V. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Infineon Technologies |
| Package | WDFN-8-EP |
| Category | Memory |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage temperature, plastic packages | -65 | 150 | °C | 31 | |||
| Ambient temperature with power applied | -65 | 125 | °C | 31 | |||
| Core supply voltage | VCC | -0.5 | 4 | V | 31 | ||
| I/O supply voltage | VIO | -0.5 | 4 | V | VIO must always be less than or equal VCC + 200 mV | 31 | |
| Output short circuit current | 100 | mA | No more than one output shorted to ground at a time, not longer than one second | 31 | |||
| Core supply voltage | VCC | 2.7 | 3.6 | V | 32 | ||
| I/O supply voltage | VIO | 1.65 | V | 1.65 V to VCC + 200 mV | 32 | ||
| Ambient temperature, Industrial Plus (V) | TA | -40 | 105 | °C | Industrial Plus (V) | 32 | |
| Input high voltage | VIH | 0.7 | x VIO | -40°C to +105°C | 35 | ||
| Input low voltage | VIL | 0.2 | x VIO | -40°C to +105°C | 35 | ||
| Output low voltage | VOL | 0.15 | x VIO | IOL = 1.6 mA, VCC = VCC min | 35 | ||
| Output high voltage | VOH | 0.85 | x VIO | IOH = -0.1 mA | 35 | ||
| Input leakage current | ILI | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 35 | |
| Output leakage current | ILO | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 35 | |
| Active supply current (READ), Serial SDR at 50 MHz | ICC1 | 22 | mA | Outputs unconnected during read data return | 35 | ||
| Active supply current (READ), Serial SDR at 133 MHz | ICC1 | 35 | mA | Outputs unconnected during read data return | 35 | ||
| Active supply current (READ), Quad SDR at 80 MHz | ICC1 | 50 | mA | Outputs unconnected during read data return | 35 | ||
| Active supply current (READ), Quad SDR at 104 MHz | ICC1 | 61 | mA | Outputs unconnected during read data return | 35 | ||
| Active supply current (READ), Quad DDR at 66 MHz | ICC1 | 75 | mA | Outputs unconnected during read data return | 35 | ||
| Active supply current (READ), Quad DDR at 80 MHz | ICC1 | 90 | mA | Outputs unconnected during read data return | 35 | ||
| Active supply current (Page program) | ICC2 | 100 | mA | CS# = VIO | 35 | ||
| Active supply current (WRR) | ICC3 | 100 | mA | CS# = VIO | 35 | ||
| Active supply current (SE) | ICC4 | 100 | mA | CS# = VIO | 35 | ||
| Active supply current (BE) | ICC5 | 100 | mA | CS# = VIO | 35 | ||
| Standby current | ISB | 70 | 300 | µA | RESET#, CS# = VIO; SI, SCK = VIO or VSS | 35 | |
| VCC minimum operation voltage | VCC (min) | 2.7 | V | 33 | |||
| VCC cut-off where re-initialization is needed | VCC (cut-off) | 2.4 | V | 33 | |||
| VCC low voltage for initialization to occur | VCC (low) | 1.6 | V | 33 | |||
| VCC (min) to read operation | tPU | 300 | µs | 33 | |||
| VCC (low) time | tPD | 15 | µs | 33 | |||
| Input capacitance (SCK, CS#, RESET#) | CIN | 8 | pF | 1 MHz | 38 | ||
| Output capacitance (all I/O) | COUT | 8 | pF | 1 MHz | 38 | ||
| Thermal resistance junction to ambient | Theta JA | 28 | °C/W | 128 Mb, WNG008, EIA/JESD51, still air (0 m/s) | 31 | ||
| Thermal resistance junction to board | Theta JB | 7.8 | °C/W | 128 Mb, WNG008 | 31 | ||
| Thermal resistance junction to case | Theta JC | 12.6 | °C/W | 128 Mb, WNG008 | 31 | ||
| Reset setup | tRS | 50 | ns | Prior reset end and RESET# HIGH before RESET# LOW | 39 | ||
| Reset pulse hold | tRPH | 35 | µs | RESET# LOW to CS# LOW | 39 | ||
| RESET# pulse width | tRP | 200 | ns | 39 | |||
| Reset hold | tRH | 50 | ns | RESET# HIGH before CS# LOW | 39 | ||
| SCK clock frequency for READ and 4READ | FSCK, R | 0 | 50 | MHz | VIO = VCC 2.7 V to 3.6 V; min printed as DC | 40 | |
| SCK clock frequency for single commands | FSCK, C | 0 | 133 | MHz | VIO = VCC 2.7 V to 3.6 V; min printed as DC | 40 | |
| SCK clock frequency for DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR | FSCK, C | 0 | 104 | MHz | VIO = VCC 2.7 V to 3.6 V; min printed as DC | 40 | |
| SCK clock frequency for QPP, 4QPP | FSCK, QPP | 0 | 80 | MHz | VIO = VCC 2.7 V to 3.6 V; min printed as DC | 40 | |
| CS# high time (Read instructions) | tCS | 10 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| CS# high time (Program/erase) | tCS | 50 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| Data in setup time | tSU | 1.5 | 3000 | ns | Max only applies during Program/Erase Suspend/Resume commands | 40 | |
| Data in hold time | tHD | 2 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| Clock low to output valid | tV | 8 | ns | Full VCC range (2.7-3.6 V) and CL = 30 pF | 40 | ||
| Output disable time | tDIS | 0 | 8 | ns | VIO = VCC 2.7 V to 3.6 V | 40 |
CAD (KiCad official)
- Symbol:
S25FL128SAGNFV000 - Footprint:
Package_DFN_QFN:WDFN-8-1EP_8x6mm_P1.27mm_EP6x4.8mm - 3D model: WDFN-8-EP, generated on the KiCad land (body 8 x 6 mm, terminals on the pads, 0.75 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
s25fl128sagnfv000-etched.step/s25fl128sagnfv000-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);s25fl128sagnfv000.step/s25fl128sagnfv000.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Infineon Technologies datasheet (165 pp, sha256
e8827e742d791a99, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).