main
Ray
s25fl128sagnfi000: the pins were read twice by one model (sonnet); say so instead of 'cross-checked by two models'
496694a
S25FL128SAGNFI000
Cypress Semicon · NOR FLASH · WSON-8-EP(6x8)
S25FL128SAGNFI000 from Cypress Semicon, in a WSON-8-EP(6x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS# | input | Chip select input that frames each SPI command; RESET# and VIO are pulled to VCC internally in this package. |
| 2 | SO/IO1 | bidirectional | Serial data output in single SPI mode, and IO1 for dual and quad I/O modes. |
| 3 | WP#/IO2 | bidirectional | Write protect input in single SPI mode, and IO2 for quad I/O mode. |
| 4 | VSS | power_in | Common ground reference for the device core, input receivers and output drivers. |
| 5 | SI/IO0 | bidirectional | Serial data input in single SPI mode, and IO0 for dual and quad I/O modes. |
| 6 | SCK | input | Serial clock input for SPI clock modes 0 and 3. |
| 7 | HOLD#/IO3 | bidirectional | Hold input in single SPI mode, and IO3 for quad I/O mode. |
| 8 | VCC | power_in | Core supply voltage for all internal logic, 2.7V to 3.6V; VIO is tied to VCC internally in this package. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cypress Semicon |
| Package | WSON-8-EP(6x8) |
| Category | Memory |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Low Voltage (min) | VIL | -0.5 | V | max is 0.2 x VIO as printed | 26 | ||
| Input Low Voltage (max, fraction of VIO) | VIL | 0.2 | x VIO | 26 | |||
| Input High Voltage (min, fraction of VIO) | VIH | 0.7 | x VIO | max is VIO+0.4 V as printed | 26 | ||
| Output Low Voltage | VOL | 0.15 | x VIO | IOL = 1.6 mA, VCC = VCC min | 26 | ||
| Output High Voltage | VOH | 0.85 | x VIO | IOH = -0.1 mA | 26 | ||
| Input Leakage Current | ILI | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 26 | |
| Output Leakage Current | ILO | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 26 | |
| Active Supply Current READ Serial SDR@50 MHz | ICC1 | 16 | mA | Outputs unconnected during read data return | 26 | ||
| Active Supply Current READ Serial SDR@133 MHz | ICC1 | 33 | mA | Outputs unconnected during read data return | 26 | ||
| Active Supply Current READ Quad SDR@80 MHz | ICC1 | 50 | mA | Outputs unconnected during read data return | 26 | ||
| Active Supply Current READ Quad SDR@104 MHz | ICC1 | 61 | mA | Outputs unconnected during read data return | 26 | ||
| Active Supply Current READ Quad DDR@66 MHz | ICC1 | 75 | mA | Outputs unconnected during read data return | 26 | ||
| Active Supply Current READ Quad DDR@80 MHz | ICC1 | 90 | mA | Outputs unconnected during read data return | 26 | ||
| Active Supply Current (Page Program) | ICC2 | 100 | mA | CS# = VIO | 26 | ||
| Active Supply Current (WRR) | ICC3 | 100 | mA | CS# = VIO | 26 | ||
| Active Supply Current (SE) | ICC4 | 100 | mA | CS# = VIO | 26 | ||
| Active Supply Current (BE) | ICC5 | 100 | mA | CS# = VIO | 26 | ||
| Standby Current (Industrial) | ISB | 70 | 100 | µA | RESET#, CS# = VIO; SI, SCK = VIO or VSS, Industrial Temp | 26 | |
| VCC (Minimum Operation Voltage) | VCC (min) | 2.7 | V | 25 | |||
| VCC (Cut Off Where Re-initialization is Needed) | VCC (cut-off) | 2.4 | V | 25 | |||
| VCC (Low Voltage for Initialization to Occur) | VCC (low) | 1.6 | V | 25 | |||
| VCC (min) to Read Operation | tPU | 300 | µs | 25 | |||
| VCC (low) Time | tPD | 15 | µs | 25 | |||
| Input Capacitance | CIN | 8 | pF | 1 MHz, applies to SCK, CS#, RESET# | 29 | ||
| Output Capacitance | COUT | 8 | pF | 1 MHz, applies to All I/O | 29 | ||
| SCK Clock Frequency for READ and 4READ | FSCK, R | 0 | 50 | MHz | VIO = VCC 2.7V to 3.6V | 31 | |
| SCK Clock Frequency for single commands | FSCK, C | 0 | 133 | MHz | VIO = VCC 2.7V to 3.6V | 31 | |
| SCK Clock Frequency for dual and quad commands | FSCK, C | 0 | 104 | MHz | DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR | 31 | |
| SCK Clock Frequency for QPP, 4QPP | FSCK, QPP | 0 | 80 | MHz | 31 | ||
| Clock Low to Output Valid | tV | 8 | ns | Full VCC range (2.7 - 3.6V) and CL = 30 pF | 31 | ||
| Data in Setup Time | tSU | 1.5 | 3000 | ns | Max only applies during Program/Erase Suspend/Resume commands | 31 | |
| Data in Hold Time | tHD | 2 | ns | 31 | |||
| Output Hold Time | tHO | 2 | ns | 31 | |||
| Output Disable Time | tDIS | 0 | 8 | ns | 31 | ||
| CS# High Time (Read Instructions) | tCS | 10 | ns | 31 | |||
| CS# High Time (Program/Erase) | tCS | 50 | ns | 31 | |||
| VCC supply voltage | VCC | 2.7 | 3.6 | V | 23 | ||
| VIO supply voltage | VIO | 1.65 | V | max is VCC +200 mV as printed | 23 | ||
| Ambient Temperature, Industrial (I) | TA | -40 | 85 | °C | 23 | ||
| Storage Temperature Plastic Packages | -65 | 150 | °C | 23 | |||
| Ambient Temperature with Power Applied | -65 | 125 | °C | 23 | |||
| VCC | VCC | -0.5 | 4 | V | 23 | ||
| VIO | VIO | -0.5 | 4 | V | VIO must always be less than or equal VCC + 200 mV | 23 | |
| Input voltage with respect to Ground (VSS) | -0.5 | V | max is VIO + 0.5V as printed | 23 | |||
| Output Short Circuit Current | 100 | mA | No more than one output shorted at a time, not longer than one second | 23 | |||
| Thermal resistance (junction to ambient) | Theta JA | 28 | °C/W | S25FL128S, WNG008 (WSON) | 23 |
CAD (KiCad official)
- Symbol:
S25FL128SAGNFI000 - Footprint:
Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm - 3D model: WSON-8-EP(6x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
s25fl128sagnfi000-etched.step/s25fl128sagnfi000-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);s25fl128sagnfi000.step/s25fl128sagnfi000.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Cypress Semicon datasheet (146 pp, sha256
4cdc2a61d3d31251, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# S25FL128SAGNFI000
**Cypress Semicon** · NOR FLASH · WSON-8-EP(6x8)
S25FL128SAGNFI000 from Cypress Semicon, in a WSON-8-EP(6x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS# | input | Chip select input that frames each SPI command; RESET# and VIO are pulled to VCC internally in this package. |
| 2 | SO/IO1 | bidirectional | Serial data output in single SPI mode, and IO1 for dual and quad I/O modes. |
| 3 | WP#/IO2 | bidirectional | Write protect input in single SPI mode, and IO2 for quad I/O mode. |
| 4 | VSS | power_in | Common ground reference for the device core, input receivers and output drivers. |
| 5 | SI/IO0 | bidirectional | Serial data input in single SPI mode, and IO0 for dual and quad I/O modes. |
| 6 | SCK | input | Serial clock input for SPI clock modes 0 and 3. |
| 7 | HOLD#/IO3 | bidirectional | Hold input in single SPI mode, and IO3 for quad I/O mode. |
| 8 | VCC | power_in | Core supply voltage for all internal logic, 2.7V to 3.6V; VIO is tied to VCC internally in this package. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cypress Semicon |
| Package | WSON-8-EP(6x8) |
| Category | Memory |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Low Voltage (min) | VIL | -0.5 | | | V | max is 0.2 x VIO as printed | 26 |
| Input Low Voltage (max, fraction of VIO) | VIL | | | 0.2 | x VIO | | 26 |
| Input High Voltage (min, fraction of VIO) | VIH | 0.7 | | | x VIO | max is VIO+0.4 V as printed | 26 |
| Output Low Voltage | VOL | | | 0.15 | x VIO | IOL = 1.6 mA, VCC = VCC min | 26 |
| Output High Voltage | VOH | 0.85 | | | x VIO | IOH = -0.1 mA | 26 |
| Input Leakage Current | ILI | -2 | | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 26 |
| Output Leakage Current | ILO | -2 | | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 26 |
| Active Supply Current READ Serial SDR@50 MHz | ICC1 | | | 16 | mA | Outputs unconnected during read data return | 26 |
| Active Supply Current READ Serial SDR@133 MHz | ICC1 | | | 33 | mA | Outputs unconnected during read data return | 26 |
| Active Supply Current READ Quad SDR@80 MHz | ICC1 | | | 50 | mA | Outputs unconnected during read data return | 26 |
| Active Supply Current READ Quad SDR@104 MHz | ICC1 | | | 61 | mA | Outputs unconnected during read data return | 26 |
| Active Supply Current READ Quad DDR@66 MHz | ICC1 | | | 75 | mA | Outputs unconnected during read data return | 26 |
| Active Supply Current READ Quad DDR@80 MHz | ICC1 | | | 90 | mA | Outputs unconnected during read data return | 26 |
| Active Supply Current (Page Program) | ICC2 | | | 100 | mA | CS# = VIO | 26 |
| Active Supply Current (WRR) | ICC3 | | | 100 | mA | CS# = VIO | 26 |
| Active Supply Current (SE) | ICC4 | | | 100 | mA | CS# = VIO | 26 |
| Active Supply Current (BE) | ICC5 | | | 100 | mA | CS# = VIO | 26 |
| Standby Current (Industrial) | ISB | | 70 | 100 | µA | RESET#, CS# = VIO; SI, SCK = VIO or VSS, Industrial Temp | 26 |
| VCC (Minimum Operation Voltage) | VCC (min) | 2.7 | | | V | | 25 |
| VCC (Cut Off Where Re-initialization is Needed) | VCC (cut-off) | 2.4 | | | V | | 25 |
| VCC (Low Voltage for Initialization to Occur) | VCC (low) | 1.6 | | | V | | 25 |
| VCC (min) to Read Operation | tPU | | | 300 | µs | | 25 |
| VCC (low) Time | tPD | 15 | | | µs | | 25 |
| Input Capacitance | CIN | | | 8 | pF | 1 MHz, applies to SCK, CS#, RESET# | 29 |
| Output Capacitance | COUT | | | 8 | pF | 1 MHz, applies to All I/O | 29 |
| SCK Clock Frequency for READ and 4READ | FSCK, R | 0 | | 50 | MHz | VIO = VCC 2.7V to 3.6V | 31 |
| SCK Clock Frequency for single commands | FSCK, C | 0 | | 133 | MHz | VIO = VCC 2.7V to 3.6V | 31 |
| SCK Clock Frequency for dual and quad commands | FSCK, C | 0 | | 104 | MHz | DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR | 31 |
| SCK Clock Frequency for QPP, 4QPP | FSCK, QPP | 0 | | 80 | MHz | | 31 |
| Clock Low to Output Valid | tV | | | 8 | ns | Full VCC range (2.7 - 3.6V) and CL = 30 pF | 31 |
| Data in Setup Time | tSU | 1.5 | | 3000 | ns | Max only applies during Program/Erase Suspend/Resume commands | 31 |
| Data in Hold Time | tHD | 2 | | | ns | | 31 |
| Output Hold Time | tHO | 2 | | | ns | | 31 |
| Output Disable Time | tDIS | 0 | | 8 | ns | | 31 |
| CS# High Time (Read Instructions) | tCS | 10 | | | ns | | 31 |
| CS# High Time (Program/Erase) | tCS | 50 | | | ns | | 31 |
| VCC supply voltage | VCC | 2.7 | | 3.6 | V | | 23 |
| VIO supply voltage | VIO | 1.65 | | | V | max is VCC +200 mV as printed | 23 |
| Ambient Temperature, Industrial (I) | TA | -40 | | 85 | °C | | 23 |
| Storage Temperature Plastic Packages | | -65 | | 150 | °C | | 23 |
| Ambient Temperature with Power Applied | | -65 | | 125 | °C | | 23 |
| VCC | VCC | -0.5 | | 4 | V | | 23 |
| VIO | VIO | -0.5 | | 4 | V | VIO must always be less than or equal VCC + 200 mV | 23 |
| Input voltage with respect to Ground (VSS) | | -0.5 | | | V | max is VIO + 0.5V as printed | 23 |
| Output Short Circuit Current | | | | 100 | mA | No more than one output shorted at a time, not longer than one second | 23 |
| Thermal resistance (junction to ambient) | Theta JA | | 28 | | °C/W | S25FL128S, WNG008 (WSON) | 23 |
## CAD (KiCad official)
- Symbol: `S25FL128SAGNFI000`
- Footprint: `Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm`
- 3D model: WSON-8-EP(6x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files: `s25fl128sagnfi000-etched.step` / `s25fl128sagnfi000-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `s25fl128sagnfi000.step` / `s25fl128sagnfi000.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Cypress Semicon datasheet](docs/s25fl128sagnfi000-datasheet.pdf) (146 pp, sha256 `4cdc2a61d3d31251`, retrieved 2026-10-30, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/s25fl128sagnfi000-datasheet.pdf)