Generated by kicad-footprint-generator · KiCad file format 20260206
S25FL128SAGMFIG00
Cypress Semicon · Pre-ordered Products · SOIC-16-300mil
S25FL128SAGMFIG00 from Cypress Semicon, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | HOLD#/IO3 | bidirectional | Hold (pause) serial transfer in single-bit or Dual commands, or IO3 in Quad mode; has an internal pull-up and may be left unconnected if Quad mode is not used. |
| 2 | VCC | power_in | Core power supply for all internal functions, 2.7 V to 3.6 V. |
| 3 | RESET# | input | Hardware reset, active LOW, which returns the device to Standby state; it has an internal pull-up and may be left unconnected if unused (printed RESET#/RFU, and the G model number is the SO footprint with RESET#). |
| 4 | DNU | unconnected | Do Not Use; has an internal pull-down, may be left unconnected or tied to VSS, and no host signal should be connected. |
| 5 | DNU | unconnected | Do Not Use; has an internal pull-down, may be left unconnected or tied to VSS, and no host signal should be connected. |
| 6 | RFU | unconnected | Reserved for Future Use; no internal signal is currently connected, and it should not be used for PCB routing. |
| 7 | CS# | input | Chip Select; LOW enables the device and HIGH deselects it with outputs at high impedance. |
| 8 | SO/IO1 | bidirectional | Serial Output for single-bit commands, or IO1 for Dual and Quad commands; data shifts out on the falling edge of SCK in SDR. |
| 9 | WP#/IO2 | bidirectional | Write Protect when not in Quad mode, or IO2 in Quad mode; it has an internal pull-up and may be left unconnected if Quad mode is not used. |
| 10 | VSS | power_in | Supply and signal ground reference for the core, input receivers and output drivers. |
| 11 | DNU | unconnected | Do Not Use; has an internal pull-down, may be left unconnected or tied to VSS, and no host signal should be connected. |
| 12 | DNU | unconnected | Do Not Use; has an internal pull-down, may be left unconnected or tied to VSS, and no host signal should be connected. |
| 13 | NC | unconnected | Not Connected; no internal signal is connected, and any signal routed to it must not exceed VIO. |
| 14 | VIO/RFU | unconnected | Printed VIO/RFU; VIO is tied to VCC inside the SO16 package for backward compatibility, and the G model number has no separate VIO supply, so treat as RFU. |
| 15 | SI/IO0 | bidirectional | Serial Input for single-bit commands, or IO0 for Dual and Quad commands; values are latched on the rising edge of SCK. |
| 16 | SCK | input | Serial Clock; instructions, addresses and data are latched on the rising edge of SCK. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cypress Semicon |
| Package | SOIC-16-300mil |
| Category | Electronic Tools/Instruments/Consumables |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage temperature, plastic packages | -65 | 150 | C | plastic packages | 31 | ||
| Ambient temperature with power applied | -65 | 125 | C | 31 | |||
| VCC supply voltage | VCC | -0.5 | 4 | V | 31 | ||
| VIO supply voltage | VIO | -0.5 | 4 | V | 31 | ||
| Input voltage with respect to ground (VSS) | -0.5 | V | max VIO + 0.5 V | 31 | |||
| Output short circuit current | 100 | mA | no more than one output shorted to ground at a time; duration not greater than one second | 31 | |||
| Core supply voltage VCC | VCC | 2.7 | 3.6 | V | 32 | ||
| I/O supply voltage VIO | VIO | 1.65 | V | VIO up to VCC +200 mV | 32 | ||
| Ambient temperature TA, Industrial (I) | TA | -40 | 85 | C | Industrial (I) grade | 32 | |
| VCC (Minimum operation voltage) | VCC (min) | 2.7 | V | 33 | |||
| VCC (Cut-off where re-initialization is needed) | VCC (cut-off) | 2.4 | V | 33 | |||
| VCC (Low voltage for initialization to occur) | VCC (low) | 1.6 | V | 33 | |||
| VCC (Low voltage for initialization to occur at embedded) | VCC (low) | 2.3 | V | at embedded | 33 | ||
| tPU VCC (min) to read operation | tPU | 300 | µs | VCC (min) to read operation | 33 | ||
| tPD VCC (low) time | tPD | 15 | µs | VCC (low) time | 33 | ||
| Input low voltage | VIL | -0.5 | V | 34 | |||
| Input leakage current | ILI | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 34 | |
| Output leakage current | ILO | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 34 | |
| Active power supply current (READ) | ICC1 | 16 | mA | Serial SDR@50 MHz; outputs unconnected during read data return | 34 | ||
| Active power supply current (READ) | ICC1 | 33 | mA | Serial SDR@133 MHz; outputs unconnected during read data return | 34 | ||
| Active power supply current (READ) | ICC1 | 50 | mA | Quad SDR@80 MHz; outputs unconnected during read data return | 34 | ||
| Active power supply current (READ) | ICC1 | 61 | mA | Quad SDR@104 MHz; outputs unconnected during read data return | 34 | ||
| Active power supply current (READ) | ICC1 | 75 | mA | Quad DDR@66 MHz; outputs unconnected during read data return | 34 | ||
| Active power supply current (READ) | ICC1 | 90 | mA | Quad DDR@80 MHz; outputs unconnected during read data return | 34 | ||
| Active power supply current (Page program) | ICC2 | 100 | mA | CS# = VIO | 34 | ||
| Active power supply current (WRR) | ICC3 | 100 | mA | CS# = VIO | 34 | ||
| Active power supply current (SE) | ICC4 | 100 | mA | CS# = VIO | 34 | ||
| Active power supply current (BE) | ICC5 | 100 | mA | CS# = VIO | 35 | ||
| Standby current (Industrial) | ISB | 70 | 100 | µA | RESET#, CS# = VIO; SI, SCK = VIO or VSS, Industrial temperature | 35 | |
| Load capacitance | CL | 30 | pF | 37 | |||
| Load capacitance | CL | 15 | pF | DDR operation | 37 | ||
| Input rise and fall times | 2.4 | ns | 37 | ||||
| Input capacitance (applies to SCK, CS#, RESET#) | CIN | 8 | pF | 1 MHz | 38 | ||
| Output capacitance (applies to All I/O) | COUT | 8 | pF | 1 MHz | 38 | ||
| Reset setup - prior reset end and RESET# HIGH before RESET# LOW | tRS | 50 | ns | 39 | |||
| Reset pulse hold - RESET# LOW to CS# LOW | tRPH | 35 | µs | 39 | |||
| RESET# pulse width | tRP | 200 | ns | 39 | |||
| Reset hold - RESET# HIGH before CS# LOW | tRH | 50 | ns | 39 | |||
| SCK clock frequency for READ and 4READ instructions | FSCK, R | 50 | MHz | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| SCK clock frequency for single commands | FSCK, C | 133 | MHz | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| SCK clock frequency for dual and Quad commands (DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR) | FSCK, C | 104 | MHz | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| SCK clock frequency for the QPP, 4QPP commands | FSCK, QPP | 80 | MHz | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| CS# high time (Read instructions) | tCS | 10 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| CS# high time (Program/erase) | tCS | 50 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| CS# active setup time (relative to SCK) | tCSS | 3 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| CS# active hold time (relative to SCK) | tCSH | 3 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| Data in setup time | tSU | 1.5 | 3000 | ns | VIO = VCC 2.7 V to 3.6 V; maximum applies only during Program/Erase Suspend/Resume commands | 40 | |
| Data in hold time | tHD | 2 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| Clock low to output valid | tV | 8 | ns | full VCC range 2.7-3.6 V and CL = 30 pF | 40 | ||
| Clock low to output valid | tV | 7.65 | ns | regulated VCC range 3.0-3.6 V and CL = 30 pF | 40 | ||
| Clock low to output valid | tV | 6.5 | ns | regulated VCC range 3.0-3.6 V and CL = 15 pF | 40 | ||
| Output hold time | tHO | 2 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| Output disable time | tDIS | 0 | 8 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | |
| WP# setup time | tWPS | 20 | ns | only applicable as a constraint for WRR instruction when SRWD is set to 1 | 40 | ||
| WP# hold time | tWPH | 100 | ns | only applicable as a constraint for WRR instruction when SRWD is set to 1 | 40 | ||
| Theta JA junction-to-ambient thermal resistance, SO3016, 128 Mb | Theta JA | 38 | °C/W | still air (0 m/s), EIA/JESD51 test method; 128 Mb device | 31 | ||
| Theta JB junction-to-board thermal resistance, SO3016, 128 Mb | Theta JB | 19.7 | °C/W | 128 Mb device | 31 | ||
| Theta JC junction-to-case thermal resistance, SO3016, 128 Mb | Theta JC | 10.9 | °C/W | 128 Mb device | 31 |
CAD (KiCad official)
- Symbol:
S25FL128SAGMFIG00 - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
s25fl128sagmfig00-etched.step/s25fl128sagmfig00-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);s25fl128sagmfig00.step/s25fl128sagmfig00.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Cypress Semicon datasheet, copy hosted by LCSC (165 pp, sha256
3c5e0c26dfe26079, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).