Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

S25FL128SAGMFIG00

Cypress Semicon · Pre-ordered Products · SOIC-16-300mil

S25FL128SAGMFIG00 from Cypress Semicon, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 HOLD#/IO3 bidirectional Hold (pause) serial transfer in single-bit or Dual commands, or IO3 in Quad mode; has an internal pull-up and may be left unconnected if Quad mode is not used.
2 VCC power_in Core power supply for all internal functions, 2.7 V to 3.6 V.
3 RESET# input Hardware reset, active LOW, which returns the device to Standby state; it has an internal pull-up and may be left unconnected if unused (printed RESET#/RFU, and the G model number is the SO footprint with RESET#).
4 DNU unconnected Do Not Use; has an internal pull-down, may be left unconnected or tied to VSS, and no host signal should be connected.
5 DNU unconnected Do Not Use; has an internal pull-down, may be left unconnected or tied to VSS, and no host signal should be connected.
6 RFU unconnected Reserved for Future Use; no internal signal is currently connected, and it should not be used for PCB routing.
7 CS# input Chip Select; LOW enables the device and HIGH deselects it with outputs at high impedance.
8 SO/IO1 bidirectional Serial Output for single-bit commands, or IO1 for Dual and Quad commands; data shifts out on the falling edge of SCK in SDR.
9 WP#/IO2 bidirectional Write Protect when not in Quad mode, or IO2 in Quad mode; it has an internal pull-up and may be left unconnected if Quad mode is not used.
10 VSS power_in Supply and signal ground reference for the core, input receivers and output drivers.
11 DNU unconnected Do Not Use; has an internal pull-down, may be left unconnected or tied to VSS, and no host signal should be connected.
12 DNU unconnected Do Not Use; has an internal pull-down, may be left unconnected or tied to VSS, and no host signal should be connected.
13 NC unconnected Not Connected; no internal signal is connected, and any signal routed to it must not exceed VIO.
14 VIO/RFU unconnected Printed VIO/RFU; VIO is tied to VCC inside the SO16 package for backward compatibility, and the G model number has no separate VIO supply, so treat as RFU.
15 SI/IO0 bidirectional Serial Input for single-bit commands, or IO0 for Dual and Quad commands; values are latched on the rising edge of SCK.
16 SCK input Serial Clock; instructions, addresses and data are latched on the rising edge of SCK.

Key specifications

Parameter Value
Manufacturer Cypress Semicon
Package SOIC-16-300mil
Category Electronic Tools/Instruments/Consumables
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Storage temperature, plastic packages -65 150 C plastic packages 31
Ambient temperature with power applied -65 125 C 31
VCC supply voltage VCC -0.5 4 V 31
VIO supply voltage VIO -0.5 4 V 31
Input voltage with respect to ground (VSS) -0.5 V max VIO + 0.5 V 31
Output short circuit current 100 mA no more than one output shorted to ground at a time; duration not greater than one second 31
Core supply voltage VCC VCC 2.7 3.6 V 32
I/O supply voltage VIO VIO 1.65 V VIO up to VCC +200 mV 32
Ambient temperature TA, Industrial (I) TA -40 85 C Industrial (I) grade 32
VCC (Minimum operation voltage) VCC (min) 2.7 V 33
VCC (Cut-off where re-initialization is needed) VCC (cut-off) 2.4 V 33
VCC (Low voltage for initialization to occur) VCC (low) 1.6 V 33
VCC (Low voltage for initialization to occur at embedded) VCC (low) 2.3 V at embedded 33
tPU VCC (min) to read operation tPU 300 µs VCC (min) to read operation 33
tPD VCC (low) time tPD 15 µs VCC (low) time 33
Input low voltage VIL -0.5 V 34
Input leakage current ILI -2 2 µA VCC = VCC Max, VIN = VIH or VIL 34
Output leakage current ILO -2 2 µA VCC = VCC Max, VIN = VIH or VIL 34
Active power supply current (READ) ICC1 16 mA Serial SDR@50 MHz; outputs unconnected during read data return 34
Active power supply current (READ) ICC1 33 mA Serial SDR@133 MHz; outputs unconnected during read data return 34
Active power supply current (READ) ICC1 50 mA Quad SDR@80 MHz; outputs unconnected during read data return 34
Active power supply current (READ) ICC1 61 mA Quad SDR@104 MHz; outputs unconnected during read data return 34
Active power supply current (READ) ICC1 75 mA Quad DDR@66 MHz; outputs unconnected during read data return 34
Active power supply current (READ) ICC1 90 mA Quad DDR@80 MHz; outputs unconnected during read data return 34
Active power supply current (Page program) ICC2 100 mA CS# = VIO 34
Active power supply current (WRR) ICC3 100 mA CS# = VIO 34
Active power supply current (SE) ICC4 100 mA CS# = VIO 34
Active power supply current (BE) ICC5 100 mA CS# = VIO 35
Standby current (Industrial) ISB 70 100 µA RESET#, CS# = VIO; SI, SCK = VIO or VSS, Industrial temperature 35
Load capacitance CL 30 pF 37
Load capacitance CL 15 pF DDR operation 37
Input rise and fall times 2.4 ns 37
Input capacitance (applies to SCK, CS#, RESET#) CIN 8 pF 1 MHz 38
Output capacitance (applies to All I/O) COUT 8 pF 1 MHz 38
Reset setup - prior reset end and RESET# HIGH before RESET# LOW tRS 50 ns 39
Reset pulse hold - RESET# LOW to CS# LOW tRPH 35 µs 39
RESET# pulse width tRP 200 ns 39
Reset hold - RESET# HIGH before CS# LOW tRH 50 ns 39
SCK clock frequency for READ and 4READ instructions FSCK, R 50 MHz VIO = VCC 2.7 V to 3.6 V 40
SCK clock frequency for single commands FSCK, C 133 MHz VIO = VCC 2.7 V to 3.6 V 40
SCK clock frequency for dual and Quad commands (DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR) FSCK, C 104 MHz VIO = VCC 2.7 V to 3.6 V 40
SCK clock frequency for the QPP, 4QPP commands FSCK, QPP 80 MHz VIO = VCC 2.7 V to 3.6 V 40
CS# high time (Read instructions) tCS 10 ns VIO = VCC 2.7 V to 3.6 V 40
CS# high time (Program/erase) tCS 50 ns VIO = VCC 2.7 V to 3.6 V 40
CS# active setup time (relative to SCK) tCSS 3 ns VIO = VCC 2.7 V to 3.6 V 40
CS# active hold time (relative to SCK) tCSH 3 ns VIO = VCC 2.7 V to 3.6 V 40
Data in setup time tSU 1.5 3000 ns VIO = VCC 2.7 V to 3.6 V; maximum applies only during Program/Erase Suspend/Resume commands 40
Data in hold time tHD 2 ns VIO = VCC 2.7 V to 3.6 V 40
Clock low to output valid tV 8 ns full VCC range 2.7-3.6 V and CL = 30 pF 40
Clock low to output valid tV 7.65 ns regulated VCC range 3.0-3.6 V and CL = 30 pF 40
Clock low to output valid tV 6.5 ns regulated VCC range 3.0-3.6 V and CL = 15 pF 40
Output hold time tHO 2 ns VIO = VCC 2.7 V to 3.6 V 40
Output disable time tDIS 0 8 ns VIO = VCC 2.7 V to 3.6 V 40
WP# setup time tWPS 20 ns only applicable as a constraint for WRR instruction when SRWD is set to 1 40
WP# hold time tWPH 100 ns only applicable as a constraint for WRR instruction when SRWD is set to 1 40
Theta JA junction-to-ambient thermal resistance, SO3016, 128 Mb Theta JA 38 °C/W still air (0 m/s), EIA/JESD51 test method; 128 Mb device 31
Theta JB junction-to-board thermal resistance, SO3016, 128 Mb Theta JB 19.7 °C/W 128 Mb device 31
Theta JC junction-to-case thermal resistance, SO3016, 128 Mb Theta JC 10.9 °C/W 128 Mb device 31

CAD (KiCad official)

  • Symbol: S25FL128SAGMFIG00
  • Footprint: Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm
  • 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
  • 3D model files: s25fl128sagmfig00-etched.step / s25fl128sagmfig00-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); s25fl128sagmfig00.step / s25fl128sagmfig00.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Cypress Semicon datasheet, copy hosted by LCSC (165 pp, sha256 3c5e0c26dfe26079, retrieved 2026-11-20)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text+vision), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF