main
Ray
Publish 0.1.0
32f6d26
S25FL064LABMFI010
Cypress Semicon · NOR FLASH · SOIC-8-208mil
S25FL064LABMFI010 from Cypress Semicon, in a SOIC-8-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS# | input | Chip Select input; the datasheet references CS# as LOW when IO3 is active in Quad-I/O or QPI mode. |
| 2 | SO/IO1 | bidirectional | Serial Output for single-bit data commands and IO1 for Dual or Quad commands. |
| 3 | WP#/IO2 | bidirectional | Write Protect when not in Quad mode (CR1V[1] = 0 and SR1NV[7] = 1) and IO2 in Quad mode (CR1V[1] = 1); it has an internal pull-up and may be left unconnected if not used for Quad commands or write protection. |
| 4 | VSS | power_in | Supply and signal ground for the device. |
| 5 | SI/IO0 | bidirectional | Serial Input for single-bit data commands and IO0 for Dual or Quad commands. |
| 6 | SCK | input | Serial Clock input for the SPI-MIO interface. |
| 7 | IO3/RESET# | bidirectional | IO3 in Quad-I/O mode (CR1V[1] = 1) or QPI mode (CR2V[3] = 1 with CS# LOW), and RESET# when enabled by CR2V[7] = 1; it has an internal pull-up and may be left unconnected if not used. |
| 8 | VCC | power_in | Voltage supply pin for the 3.0 Volt-only device. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cypress Semicon |
| Package | SOIC-8-208mil |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VCC (operating range) | VCC | 2.7 | 3.6 | V | 119 | ||
| Ambient Temperature, Industrial (I) | TA | -40 | 85 | °C | Industrial (I) grade | 119 | |
| VCC absolute maximum | VCC | -0.5 | 4 | V | 119 | ||
| Storage Temperature | TSTG | -65 | 150 | °C | Plastic packages | 119 | |
| Ambient Temperature with Power Applied | -65 | 125 | °C | Power applied | 119 | ||
| Output Short Circuit Current | 100 | mA | No more than one output shorted to ground at a time; duration not greater than one second | 119 | |||
| VCC Current (latchup) | -100 | 100 | mA | 119 | |||
| Input Low Voltage | VIL | -0.5 | V | 122 | |||
| Output Low Voltage | VOL | 0.2 | V | IOL = 0.1 mA, VCC = VCC min | 122 | ||
| Input Leakage Current | ILI | -2 | 2 | µA | VCC=VCC Max, VIN=VIH or VSS, CS# = VIH | 122 | |
| Output Leakage Current | ILO | -2 | 2 | µA | VCC=VCC Max, VIN=VIH or VSS, CS# = VIH | 122 | |
| Active Power Supply Current (READ) | ICC1 | 10 | 15 | mA | Serial SDR@5 MHz | 122 | |
| Active Power Supply Current (READ) | ICC1 | 15 | 20 | mA | Serial SDR@50 MHz | 122 | |
| Active Power Supply Current (READ) | ICC1 | 20 | 25 | mA | Serial SDR@108 MHz | 122 | |
| Active Power Supply Current (READ) | ICC1 | 20 | 30 | mA | QIO/QPI SDR@108 MHz | 122 | |
| Active Power Supply Current (READ) | ICC1 | 17 | 25 | mA | QIO/QPI DDR@54 MHz | 122 | |
| Active Power Supply Current (Page Program) | ICC2 | 17 | 25 | mA | CS#=VCC | 122 | |
| Active Power Supply Current (WRR or WRAR) | ICC3 | 11 | 20 | mA | CS#=VCC | 122 | |
| Active Power Supply Current (SE) | ICC4 | 17 | 25 | mA | CS#=VCC | 122 | |
| Active Power Supply Current (HBE, BE) | ICC5 | 15 | 25 | mA | CS#=VCC | 122 | |
| Standby Current | ISB | 20 | 30 | µA | RESET#, CS#=VCC; SI, SCK = VCC or VSS: SPI, Dual I/O and Quad I/O Modes | 122 | |
| Standby Current | ISB | 35 | 55 | µA | RESET#, CS#=VCC; SI, SCK = VCC or VSS: QPI Mode | 122 | |
| Deep Power Down Current | IDPD | 2 | 20 | µA | RESET#, CS# = VCC, VIN = GND or VCC | 122 | |
| Power On Reset Current | IPOR | 3 | 5 | mA | RESET#, CS#=VCC; SI, SCK = VCC or VSS | 122 | |
| VCC (minimum operation voltage) | VCC(min) | 2.7 | V | 121 | |||
| VCC (cut-off, re-initialization needed) | VCC(cut-off) | 2.4 | V | 121 | |||
| VCC (low, initialization occurs) | VCC(low) | 1 | V | 121 | |||
| VCC(min) to Read operation (tPU) | tPU | 300 | µs | VCC(min) to Read operation | 121 | ||
| Reset Setup (tRS) | tRS | 50 | ns | Prior reset end and RESET# HIGH before RESET# LOW | 127 | ||
| Reset Pulse Hold (tRPH) | tRPH | 100 | µs | RESET# LOW to CS# LOW | 127 | ||
| RESET# Pulse Width (tRP) | tRP | 200 | ns | 127 | |||
| Reset Hold (tRH) | tRH | 150 | ns | RESET# HIGH before CS# LOW | 127 | ||
| Input Capacitance (CIN) | CIN | 8 | pF | 1 MHz; applies to SCK, CS#, RESET#, IO3/RESET# | 126 | ||
| Output Capacitance (COUT) | COUT | 8 | pF | 1 MHz; applies to all I/O | 126 | ||
| SCK Clock Frequency for READ and 4READ | FSCK,R | 50 | MHz | READ and 4READ instructions | 129 | ||
| SCK Clock Frequency for dual and quad commands | FSCK,C | 108 | MHz | QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR | 129 | ||
| CS# High Time (Any Read Instructions) | tCS | 20 | ns | Any read instructions | 129 | ||
| CS# High Time (All other Non-Read instructions) | tCS | 50 | ns | All other non-read instructions | 129 | ||
| CS# Active Setup Time (relative to SCK) | tCSS | 3 | ns | 129 | |||
| CS# Active Hold Time (relative to SCK) | tCSH | 5 | ns | 129 | |||
| Data in Setup Time | tSU | 3 | ns | 129 | |||
| Data in Hold Time | tHD | 2 | ns | 129 | |||
| Clock Low to Output Valid | tV | 8 | ns | Full VCC range and CL = 30 pF | 129 | ||
| Clock Low to Output Valid | tV | 6 | ns | Full VCC range and CL = 15 pF | 129 | ||
| Output Hold Time | tHO | 1 | ns | 129 | |||
| Output Disable Time | tDIS | 8 | ns | 129 | |||
| Output Disable Time (Reset feature and Quad mode both enabled) | tDIS | 20 | ns | Reset feature and Quad mode both enabled | 129 | ||
| WP# Setup Time | tWPS | 20 | ns | Only applicable for WRR or WRAR when SRP0 is set to 1 | 129 | ||
| WP# Hold Time | tWPH | 100 | ns | Only applicable for WRR or WRAR when SRP0 is set to 1 | 129 | ||
| Thermal Resistance, junction to ambient (θJA) | θJA | 65.8 | °C/W | SOC008 (8-lead SOIC, 208 mil) package | 119 |
CAD (KiCad official)
- Symbol:
S25FL064LABMFI010 - Footprint:
Package_SO:SOIC-8_5.3x5.3mm_P1.27mm - 3D model: SOIC-8-208mil (KiCad packages3D, STEP)
- 3D model files:
s25fl064labmfi010-etched.step/s25fl064labmfi010-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);s25fl064labmfi010.step/s25fl064labmfi010.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Cypress Semicon datasheet (147 pp, sha256
7d43a6181025337a, retrieved 2026-11-05, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# S25FL064LABMFI010
**Cypress Semicon** · NOR FLASH · SOIC-8-208mil
S25FL064LABMFI010 from Cypress Semicon, in a SOIC-8-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS# | input | Chip Select input; the datasheet references CS# as LOW when IO3 is active in Quad-I/O or QPI mode. |
| 2 | SO/IO1 | bidirectional | Serial Output for single-bit data commands and IO1 for Dual or Quad commands. |
| 3 | WP#/IO2 | bidirectional | Write Protect when not in Quad mode (CR1V[1] = 0 and SR1NV[7] = 1) and IO2 in Quad mode (CR1V[1] = 1); it has an internal pull-up and may be left unconnected if not used for Quad commands or write protection. |
| 4 | VSS | power_in | Supply and signal ground for the device. |
| 5 | SI/IO0 | bidirectional | Serial Input for single-bit data commands and IO0 for Dual or Quad commands. |
| 6 | SCK | input | Serial Clock input for the SPI-MIO interface. |
| 7 | IO3/RESET# | bidirectional | IO3 in Quad-I/O mode (CR1V[1] = 1) or QPI mode (CR2V[3] = 1 with CS# LOW), and RESET# when enabled by CR2V[7] = 1; it has an internal pull-up and may be left unconnected if not used. |
| 8 | VCC | power_in | Voltage supply pin for the 3.0 Volt-only device. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cypress Semicon |
| Package | SOIC-8-208mil |
| Category | Memory |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VCC (operating range) | VCC | 2.7 | | 3.6 | V | | 119 |
| Ambient Temperature, Industrial (I) | TA | -40 | | 85 | °C | Industrial (I) grade | 119 |
| VCC absolute maximum | VCC | -0.5 | | 4 | V | | 119 |
| Storage Temperature | TSTG | -65 | | 150 | °C | Plastic packages | 119 |
| Ambient Temperature with Power Applied | | -65 | | 125 | °C | Power applied | 119 |
| Output Short Circuit Current | | | | 100 | mA | No more than one output shorted to ground at a time; duration not greater than one second | 119 |
| VCC Current (latchup) | | -100 | | 100 | mA | | 119 |
| Input Low Voltage | VIL | -0.5 | | | V | | 122 |
| Output Low Voltage | VOL | | | 0.2 | V | IOL = 0.1 mA, VCC = VCC min | 122 |
| Input Leakage Current | ILI | -2 | | 2 | µA | VCC=VCC Max, VIN=VIH or VSS, CS# = VIH | 122 |
| Output Leakage Current | ILO | -2 | | 2 | µA | VCC=VCC Max, VIN=VIH or VSS, CS# = VIH | 122 |
| Active Power Supply Current (READ) | ICC1 | | 10 | 15 | mA | Serial SDR@5 MHz | 122 |
| Active Power Supply Current (READ) | ICC1 | | 15 | 20 | mA | Serial SDR@50 MHz | 122 |
| Active Power Supply Current (READ) | ICC1 | | 20 | 25 | mA | Serial SDR@108 MHz | 122 |
| Active Power Supply Current (READ) | ICC1 | | 20 | 30 | mA | QIO/QPI SDR@108 MHz | 122 |
| Active Power Supply Current (READ) | ICC1 | | 17 | 25 | mA | QIO/QPI DDR@54 MHz | 122 |
| Active Power Supply Current (Page Program) | ICC2 | | 17 | 25 | mA | CS#=VCC | 122 |
| Active Power Supply Current (WRR or WRAR) | ICC3 | | 11 | 20 | mA | CS#=VCC | 122 |
| Active Power Supply Current (SE) | ICC4 | | 17 | 25 | mA | CS#=VCC | 122 |
| Active Power Supply Current (HBE, BE) | ICC5 | | 15 | 25 | mA | CS#=VCC | 122 |
| Standby Current | ISB | | 20 | 30 | µA | RESET#, CS#=VCC; SI, SCK = VCC or VSS: SPI, Dual I/O and Quad I/O Modes | 122 |
| Standby Current | ISB | | 35 | 55 | µA | RESET#, CS#=VCC; SI, SCK = VCC or VSS: QPI Mode | 122 |
| Deep Power Down Current | IDPD | | 2 | 20 | µA | RESET#, CS# = VCC, VIN = GND or VCC | 122 |
| Power On Reset Current | IPOR | | 3 | 5 | mA | RESET#, CS#=VCC; SI, SCK = VCC or VSS | 122 |
| VCC (minimum operation voltage) | VCC(min) | 2.7 | | | V | | 121 |
| VCC (cut-off, re-initialization needed) | VCC(cut-off) | | | 2.4 | V | | 121 |
| VCC (low, initialization occurs) | VCC(low) | | | 1 | V | | 121 |
| VCC(min) to Read operation (tPU) | tPU | | | 300 | µs | VCC(min) to Read operation | 121 |
| Reset Setup (tRS) | tRS | 50 | | | ns | Prior reset end and RESET# HIGH before RESET# LOW | 127 |
| Reset Pulse Hold (tRPH) | tRPH | 100 | | | µs | RESET# LOW to CS# LOW | 127 |
| RESET# Pulse Width (tRP) | tRP | 200 | | | ns | | 127 |
| Reset Hold (tRH) | tRH | 150 | | | ns | RESET# HIGH before CS# LOW | 127 |
| Input Capacitance (CIN) | CIN | | | 8 | pF | 1 MHz; applies to SCK, CS#, RESET#, IO3/RESET# | 126 |
| Output Capacitance (COUT) | COUT | | | 8 | pF | 1 MHz; applies to all I/O | 126 |
| SCK Clock Frequency for READ and 4READ | FSCK,R | | | 50 | MHz | READ and 4READ instructions | 129 |
| SCK Clock Frequency for dual and quad commands | FSCK,C | | | 108 | MHz | QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR | 129 |
| CS# High Time (Any Read Instructions) | tCS | 20 | | | ns | Any read instructions | 129 |
| CS# High Time (All other Non-Read instructions) | tCS | 50 | | | ns | All other non-read instructions | 129 |
| CS# Active Setup Time (relative to SCK) | tCSS | 3 | | | ns | | 129 |
| CS# Active Hold Time (relative to SCK) | tCSH | 5 | | | ns | | 129 |
| Data in Setup Time | tSU | 3 | | | ns | | 129 |
| Data in Hold Time | tHD | 2 | | | ns | | 129 |
| Clock Low to Output Valid | tV | | | 8 | ns | Full VCC range and CL = 30 pF | 129 |
| Clock Low to Output Valid | tV | | | 6 | ns | Full VCC range and CL = 15 pF | 129 |
| Output Hold Time | tHO | 1 | | | ns | | 129 |
| Output Disable Time | tDIS | | | 8 | ns | | 129 |
| Output Disable Time (Reset feature and Quad mode both enabled) | tDIS | | | 20 | ns | Reset feature and Quad mode both enabled | 129 |
| WP# Setup Time | tWPS | 20 | | | ns | Only applicable for WRR or WRAR when SRP0 is set to 1 | 129 |
| WP# Hold Time | tWPH | 100 | | | ns | Only applicable for WRR or WRAR when SRP0 is set to 1 | 129 |
| Thermal Resistance, junction to ambient (θJA) | θJA | | 65.8 | | °C/W | SOC008 (8-lead SOIC, 208 mil) package | 119 |
## CAD (KiCad official)
- Symbol: `S25FL064LABMFI010`
- Footprint: `Package_SO:SOIC-8_5.3x5.3mm_P1.27mm`
- 3D model: SOIC-8-208mil (KiCad packages3D, STEP)
- 3D model files: `s25fl064labmfi010-etched.step` / `s25fl064labmfi010-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `s25fl064labmfi010.step` / `s25fl064labmfi010.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Cypress Semicon datasheet](docs/s25fl064labmfi010-datasheet.pdf) (147 pp, sha256 `7d43a6181025337a`, retrieved 2026-11-05, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/s25fl064labmfi010-datasheet.pdf)