Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

S25FL064LABMFI010

Cypress Semicon · NOR FLASH · SOIC-8-208mil

S25FL064LABMFI010 from Cypress Semicon, in a SOIC-8-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CS# input Chip Select input; the datasheet references CS# as LOW when IO3 is active in Quad-I/O or QPI mode.
2 SO/IO1 bidirectional Serial Output for single-bit data commands and IO1 for Dual or Quad commands.
3 WP#/IO2 bidirectional Write Protect when not in Quad mode (CR1V[1] = 0 and SR1NV[7] = 1) and IO2 in Quad mode (CR1V[1] = 1); it has an internal pull-up and may be left unconnected if not used for Quad commands or write protection.
4 VSS power_in Supply and signal ground for the device.
5 SI/IO0 bidirectional Serial Input for single-bit data commands and IO0 for Dual or Quad commands.
6 SCK input Serial Clock input for the SPI-MIO interface.
7 IO3/RESET# bidirectional IO3 in Quad-I/O mode (CR1V[1] = 1) or QPI mode (CR2V[3] = 1 with CS# LOW), and RESET# when enabled by CR2V[7] = 1; it has an internal pull-up and may be left unconnected if not used.
8 VCC power_in Voltage supply pin for the 3.0 Volt-only device.

Key specifications

Parameter Value
Manufacturer Cypress Semicon
Package SOIC-8-208mil
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC (operating range) VCC 2.7 3.6 V 119
Ambient Temperature, Industrial (I) TA -40 85 °C Industrial (I) grade 119
VCC absolute maximum VCC -0.5 4 V 119
Storage Temperature TSTG -65 150 °C Plastic packages 119
Ambient Temperature with Power Applied -65 125 °C Power applied 119
Output Short Circuit Current 100 mA No more than one output shorted to ground at a time; duration not greater than one second 119
VCC Current (latchup) -100 100 mA 119
Input Low Voltage VIL -0.5 V 122
Output Low Voltage VOL 0.2 V IOL = 0.1 mA, VCC = VCC min 122
Input Leakage Current ILI -2 2 µA VCC=VCC Max, VIN=VIH or VSS, CS# = VIH 122
Output Leakage Current ILO -2 2 µA VCC=VCC Max, VIN=VIH or VSS, CS# = VIH 122
Active Power Supply Current (READ) ICC1 10 15 mA Serial SDR@5 MHz 122
Active Power Supply Current (READ) ICC1 15 20 mA Serial SDR@50 MHz 122
Active Power Supply Current (READ) ICC1 20 25 mA Serial SDR@108 MHz 122
Active Power Supply Current (READ) ICC1 20 30 mA QIO/QPI SDR@108 MHz 122
Active Power Supply Current (READ) ICC1 17 25 mA QIO/QPI DDR@54 MHz 122
Active Power Supply Current (Page Program) ICC2 17 25 mA CS#=VCC 122
Active Power Supply Current (WRR or WRAR) ICC3 11 20 mA CS#=VCC 122
Active Power Supply Current (SE) ICC4 17 25 mA CS#=VCC 122
Active Power Supply Current (HBE, BE) ICC5 15 25 mA CS#=VCC 122
Standby Current ISB 20 30 µA RESET#, CS#=VCC; SI, SCK = VCC or VSS: SPI, Dual I/O and Quad I/O Modes 122
Standby Current ISB 35 55 µA RESET#, CS#=VCC; SI, SCK = VCC or VSS: QPI Mode 122
Deep Power Down Current IDPD 2 20 µA RESET#, CS# = VCC, VIN = GND or VCC 122
Power On Reset Current IPOR 3 5 mA RESET#, CS#=VCC; SI, SCK = VCC or VSS 122
VCC (minimum operation voltage) VCC(min) 2.7 V 121
VCC (cut-off, re-initialization needed) VCC(cut-off) 2.4 V 121
VCC (low, initialization occurs) VCC(low) 1 V 121
VCC(min) to Read operation (tPU) tPU 300 µs VCC(min) to Read operation 121
Reset Setup (tRS) tRS 50 ns Prior reset end and RESET# HIGH before RESET# LOW 127
Reset Pulse Hold (tRPH) tRPH 100 µs RESET# LOW to CS# LOW 127
RESET# Pulse Width (tRP) tRP 200 ns 127
Reset Hold (tRH) tRH 150 ns RESET# HIGH before CS# LOW 127
Input Capacitance (CIN) CIN 8 pF 1 MHz; applies to SCK, CS#, RESET#, IO3/RESET# 126
Output Capacitance (COUT) COUT 8 pF 1 MHz; applies to all I/O 126
SCK Clock Frequency for READ and 4READ FSCK,R 50 MHz READ and 4READ instructions 129
SCK Clock Frequency for dual and quad commands FSCK,C 108 MHz QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR 129
CS# High Time (Any Read Instructions) tCS 20 ns Any read instructions 129
CS# High Time (All other Non-Read instructions) tCS 50 ns All other non-read instructions 129
CS# Active Setup Time (relative to SCK) tCSS 3 ns 129
CS# Active Hold Time (relative to SCK) tCSH 5 ns 129
Data in Setup Time tSU 3 ns 129
Data in Hold Time tHD 2 ns 129
Clock Low to Output Valid tV 8 ns Full VCC range and CL = 30 pF 129
Clock Low to Output Valid tV 6 ns Full VCC range and CL = 15 pF 129
Output Hold Time tHO 1 ns 129
Output Disable Time tDIS 8 ns 129
Output Disable Time (Reset feature and Quad mode both enabled) tDIS 20 ns Reset feature and Quad mode both enabled 129
WP# Setup Time tWPS 20 ns Only applicable for WRR or WRAR when SRP0 is set to 1 129
WP# Hold Time tWPH 100 ns Only applicable for WRR or WRAR when SRP0 is set to 1 129
Thermal Resistance, junction to ambient (θJA) θJA 65.8 °C/W SOC008 (8-lead SOIC, 208 mil) package 119

CAD (KiCad official)

  • Symbol: S25FL064LABMFI010
  • Footprint: Package_SO:SOIC-8_5.3x5.3mm_P1.27mm
  • 3D model: SOIC-8-208mil (KiCad packages3D, STEP)
  • 3D model files: s25fl064labmfi010-etched.step / s25fl064labmfi010-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); s25fl064labmfi010.step / s25fl064labmfi010.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Cypress Semicon datasheet (147 pp, sha256 7d43a6181025337a, retrieved 2026-11-05, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF