main
Ray
Publish 0.1.0
576075e
RTQ2513TGQW
Richtek Tech · Linear Voltage Regulators (LDO) · VQFN-20(3.5x3.5)
RTQ2513TGQW from Richtek Tech, in a VQFN-20(3.5x3.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VOUT | power_out | LDO output pin; requires a 10µF or larger ceramic capacitor (4.7µF or greater effective) placed close to the device for stability. |
| 2 | SNS | input | Output voltage sense input; connect only when setting VOUT by PCB layout, and keep floating if VOUT is set by an external resistor. |
| 3 | FB | input | Feedback voltage input used to set the output voltage via an external resistive divider, with a typical 0.5V reference. |
| 4 | PGOOD | output | Open-drain power-good output, active high when VOUT reaches 88% of target and pulled low on undervoltage, EN shutdown, OCP and OTP. |
| 5 | 50mV | passive | Output voltage setting pin; connect to ground to add 50mV to the output voltage, or leave floating if VOUT is set by an external resistor. |
| 6 | 100mV | passive | Output voltage setting pin; connect to ground to add 100mV to the output voltage, or leave floating if VOUT is set by an external resistor. |
| 7 | 200mV | passive | Output voltage setting pin; connect to ground to add 200mV to the output voltage, or leave floating if VOUT is set by an external resistor. |
| 8 | GND | power_in | Ground pin. |
| 9 | 400mV | passive | Output voltage setting pin; connect to ground to add 400mV to the output voltage, or leave floating if VOUT is set by an external resistor. |
| 10 | 800mV | passive | Output voltage setting pin; connect to ground to add 800mV to the output voltage, or leave floating if VOUT is set by an external resistor. |
| 11 | 1.6V | passive | Output voltage setting pin; connect to ground to add 1.6V to the output voltage, or leave floating if VOUT is set by an external resistor. |
| 12 | NC | unconnected | No internal connection; may be left floating or tied to GND to extend top-layer GND copper for thermal convection. |
| 13 | NR/SS | passive | Noise-reduction and soft-start pin; a capacitor to GND (10nF to 1µF suggested for low noise) reduces output noise and slows the VOUT rise. |
| 14 | EN | input | Enable control input; logic high enables the regulator and driving it low puts the device in shutdown mode. |
| 15 | VIN | power_in | Supply input; place a minimum 22µF ceramic capacitor as close as possible for better noise rejection. |
| 16 | VIN | power_in | Supply input; place a minimum 22µF ceramic capacitor as close as possible for better noise rejection. |
| 17 | VIN | power_in | Supply input; place a minimum 22µF ceramic capacitor as close as possible for better noise rejection. |
| 18 | GND | power_in | Ground pin. |
| 19 | VOUT | power_out | LDO output pin; requires a 10µF or larger ceramic capacitor (4.7µF or greater effective) placed close to the device for stability. |
| 20 | VOUT | power_out | LDO output pin; requires a 10µF or larger ceramic capacitor (4.7µF or greater effective) placed close to the device for stability. |
| 21 | GND | power_in | Exposed pad ground; must be soldered to a large PCB GND area for maximum power dissipation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Richtek Tech |
| Package | VQFN-20(3.5x3.5) |
| Category | Power Management |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Input Voltage Range | VIN | 1.1 | 6.5 | V | 5 | ||
| Under-Voltage Lockout | VUVLO | 1.02 | 1.085 | V | VIN increasing | 5 | |
| Output Voltage Range (voltage setting pins) | VOUT | 0.5 | 3.65 | V | Using voltage setting pins (50mV, 100mV, 200mV, 400mV, 800mV, and 1.6V) | 5 | |
| Output Voltage Range (external resistors) | VOUT | 0.5 | 5.5 | V | Using external resistors | 5 | |
| Output Voltage Accuracy | VOUT | -1 | 1 | % | VIN = VOUT + 0.3V, 0.5V ≤ VOUT ≤ 5.5V, 5mA ≤ IOUT ≤ 3A | 5 | |
| Dropout Voltage | VDROP | 110 | 180 | mV | VIN = 1.1V to 6.5V, IOUT = 3A, VFB = 0.5V ± 3% | 6 | |
| Output Current Limit | ILIM | 3.7 | 4.2 | 4.7 | A | VOUT = 90% VOUT(TARGET), VIN = VOUT(TARGET) + 400mV | 6 |
| Ground Pin Current (min load) | IGND | 2.8 | 4 | mA | Minimum load, VIN = 6.5V, IOUT = 5mA | 6 | |
| Ground Pin Current (max load) | IGND | 4.2 | 5.5 | mA | Maximum load, VIN = 1.4V, IOUT = 3A | 6 | |
| Ground Pin Current (shutdown) | IGND | 25 | µA | Shutdown, PGOOD = Open, VIN = 6.5V, VEN = 0.5V | 6 | ||
| EN Pin Current | IEN | -0.1 | 0.1 | µA | VIN = 6.5V, VEN = 0V and 6.5V | 6 | |
| EN Pin High-Level Input Voltage | VEN_H | 1.1 | 6.5 | V | Enable device | 6 | |
| EN Pin Low-Level Input Voltage | VEN_L | 0 | 0.5 | V | Disable device | 6 | |
| PGOOD Pin Threshold | VIT_PGOOD | 0.82 | 0.883 | 0.93 | V | PGOOD signal falling with decreasing VOUT (values are multiples of VOUT) | 6 |
| PGOOD Pin Low-Level Output Voltage | VPGOOD_L | 0.4 | V | VOUT < VIT_PGOOD, IPGOOD = 1mA (current into device) | 6 | ||
| PGOOD Pin Leakage Current | IPGOOD_LK | 1 | µA | VOUT > VIT_PGOOD, VPGOOD = 6.5V | 6 | ||
| NR/SS Pin Charging Current | INR/SS | 4 | 6.2 | 9 | µA | VNR/SS = GND, VIN = 6.5V | 6 |
| FB Pin Leakage Current | IFB | -100 | 100 | nA | VIN = 6.5V | 6 | |
| Feedback Reference Voltage | VREF | 0.5 | V | 5 | |||
| UVLO Hysteresis | VUVLO hysteresis | 150 | mV | 5 | |||
| Line Regulation | ΔVOUT/ΔVIN | 0.05 | %/V | IOUT = 5mA, 1.4V ≤ VIN ≤ 6.5V | 5 | ||
| Load Regulation | ΔVOUT/ΔIOUT | 0.08 | %/A | 5mA ≤ IOUT ≤ 3A | 5 | ||
| Output Noise Voltage 0.5V | eNO | 7 | µVRMS | BW = 10Hz to 100kHz, IOUT = 3A, CNR/SS = 100nF, CFF = 10nF, COUT = 22µF, VIN = 1.1V, VOUT = 0.5V | 6 | ||
| Output Noise Voltage 3.3V | eNO | 10 | µVRMS | VOUT = 3.3V | 6 | ||
| Thermal Shutdown Threshold (increasing) | TSD | 160 | °C | Temperature increasing | 7 | ||
| Thermal Shutdown Threshold (decreasing) | TSD | 140 | °C | Temperature decreasing | 7 | ||
| Abs Max VIN, PGOOD, EN | -0.3 | 7 | V | 5 | |||
| Abs Max VOUT | -0.3 | V | to (VIN + 0.3V) | 5 | |||
| Abs Max NR/SS, FB | -0.3 | 3.6 | V | 5 | |||
| Power Dissipation | PD | 3.5 | W | TA = 25°C, WQFN-20L 3.5x3.5 | 5 | ||
| Lead Temperature | 260 | °C | Soldering, 10 sec | 5 | |||
| Junction Temperature | TJ | 150 | °C | 5 | |||
| Storage Temperature | -65 | 150 | °C | 5 | |||
| ESD HBM | 2 | kV | Human Body Model | 5 | |||
| ESD CDM | 1 | kV | Charged Device Model | 5 | |||
| Supply Input Voltage (recommended) | VIN | 1.1 | 6.5 | V | 5 | ||
| Junction Temperature Range (recommended) | TJ | -40 | 125 | °C | 5 | ||
| Thermal Resistance Junction-to-Ambient | θJA | 28.5 | °C/W | WQFN-20L 3.5x3.5, JEDEC 51-7 four-layer board, still air, TA = 25°C | 5 | ||
| Thermal Resistance Junction-to-Case | θJC | 7.2 | °C/W | WQFN-20L 3.5x3.5, measured at exposed pad | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | functionality. By connecting these pins to GND, design engineers can extend the GND copper coverage on the PCB top layer to enhance the thermal | 2 |
CAD (KiCad official)
- Symbol:
RTQ2513TGQW - Footprint:
Package_DFN_QFN:QFN-20-1EP_3.5x3.5mm_P0.5mm_EP2x2mm - 3D model: VQFN-20(3.5x3.5), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
rtq2513tgqw-etched.step/rtq2513tgqw-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);rtq2513tgqw.step/rtq2513tgqw.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Richtek Tech datasheet (18 pp, sha256
4e38b49659b0f27b, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# RTQ2513TGQW
**Richtek Tech** · Linear Voltage Regulators (LDO) · VQFN-20(3.5x3.5)
RTQ2513TGQW from Richtek Tech, in a VQFN-20(3.5x3.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VOUT | power_out | LDO output pin; requires a 10µF or larger ceramic capacitor (4.7µF or greater effective) placed close to the device for stability. |
| 2 | SNS | input | Output voltage sense input; connect only when setting VOUT by PCB layout, and keep floating if VOUT is set by an external resistor. |
| 3 | FB | input | Feedback voltage input used to set the output voltage via an external resistive divider, with a typical 0.5V reference. |
| 4 | PGOOD | output | Open-drain power-good output, active high when VOUT reaches 88% of target and pulled low on undervoltage, EN shutdown, OCP and OTP. |
| 5 | 50mV | passive | Output voltage setting pin; connect to ground to add 50mV to the output voltage, or leave floating if VOUT is set by an external resistor. |
| 6 | 100mV | passive | Output voltage setting pin; connect to ground to add 100mV to the output voltage, or leave floating if VOUT is set by an external resistor. |
| 7 | 200mV | passive | Output voltage setting pin; connect to ground to add 200mV to the output voltage, or leave floating if VOUT is set by an external resistor. |
| 8 | GND | power_in | Ground pin. |
| 9 | 400mV | passive | Output voltage setting pin; connect to ground to add 400mV to the output voltage, or leave floating if VOUT is set by an external resistor. |
| 10 | 800mV | passive | Output voltage setting pin; connect to ground to add 800mV to the output voltage, or leave floating if VOUT is set by an external resistor. |
| 11 | 1.6V | passive | Output voltage setting pin; connect to ground to add 1.6V to the output voltage, or leave floating if VOUT is set by an external resistor. |
| 12 | NC | unconnected | No internal connection; may be left floating or tied to GND to extend top-layer GND copper for thermal convection. |
| 13 | NR/SS | passive | Noise-reduction and soft-start pin; a capacitor to GND (10nF to 1µF suggested for low noise) reduces output noise and slows the VOUT rise. |
| 14 | EN | input | Enable control input; logic high enables the regulator and driving it low puts the device in shutdown mode. |
| 15 | VIN | power_in | Supply input; place a minimum 22µF ceramic capacitor as close as possible for better noise rejection. |
| 16 | VIN | power_in | Supply input; place a minimum 22µF ceramic capacitor as close as possible for better noise rejection. |
| 17 | VIN | power_in | Supply input; place a minimum 22µF ceramic capacitor as close as possible for better noise rejection. |
| 18 | GND | power_in | Ground pin. |
| 19 | VOUT | power_out | LDO output pin; requires a 10µF or larger ceramic capacitor (4.7µF or greater effective) placed close to the device for stability. |
| 20 | VOUT | power_out | LDO output pin; requires a 10µF or larger ceramic capacitor (4.7µF or greater effective) placed close to the device for stability. |
| 21 | GND | power_in | Exposed pad ground; must be soldered to a large PCB GND area for maximum power dissipation. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Richtek Tech |
| Package | VQFN-20(3.5x3.5) |
| Category | Power Management |
| Pins | 21 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Input Voltage Range | VIN | 1.1 | | 6.5 | V | | 5 |
| Under-Voltage Lockout | VUVLO | | 1.02 | 1.085 | V | VIN increasing | 5 |
| Output Voltage Range (voltage setting pins) | VOUT | 0.5 | | 3.65 | V | Using voltage setting pins (50mV, 100mV, 200mV, 400mV, 800mV, and 1.6V) | 5 |
| Output Voltage Range (external resistors) | VOUT | 0.5 | | 5.5 | V | Using external resistors | 5 |
| Output Voltage Accuracy | VOUT | -1 | | 1 | % | VIN = VOUT + 0.3V, 0.5V ≤ VOUT ≤ 5.5V, 5mA ≤ IOUT ≤ 3A | 5 |
| Dropout Voltage | VDROP | | 110 | 180 | mV | VIN = 1.1V to 6.5V, IOUT = 3A, VFB = 0.5V ± 3% | 6 |
| Output Current Limit | ILIM | 3.7 | 4.2 | 4.7 | A | VOUT = 90% VOUT(TARGET), VIN = VOUT(TARGET) + 400mV | 6 |
| Ground Pin Current (min load) | IGND | | 2.8 | 4 | mA | Minimum load, VIN = 6.5V, IOUT = 5mA | 6 |
| Ground Pin Current (max load) | IGND | | 4.2 | 5.5 | mA | Maximum load, VIN = 1.4V, IOUT = 3A | 6 |
| Ground Pin Current (shutdown) | IGND | | | 25 | µA | Shutdown, PGOOD = Open, VIN = 6.5V, VEN = 0.5V | 6 |
| EN Pin Current | IEN | -0.1 | | 0.1 | µA | VIN = 6.5V, VEN = 0V and 6.5V | 6 |
| EN Pin High-Level Input Voltage | VEN_H | 1.1 | | 6.5 | V | Enable device | 6 |
| EN Pin Low-Level Input Voltage | VEN_L | 0 | | 0.5 | V | Disable device | 6 |
| PGOOD Pin Threshold | VIT_PGOOD | 0.82 | 0.883 | 0.93 | V | PGOOD signal falling with decreasing VOUT (values are multiples of VOUT) | 6 |
| PGOOD Pin Low-Level Output Voltage | VPGOOD_L | | | 0.4 | V | VOUT < VIT_PGOOD, IPGOOD = 1mA (current into device) | 6 |
| PGOOD Pin Leakage Current | IPGOOD_LK | | | 1 | µA | VOUT > VIT_PGOOD, VPGOOD = 6.5V | 6 |
| NR/SS Pin Charging Current | INR/SS | 4 | 6.2 | 9 | µA | VNR/SS = GND, VIN = 6.5V | 6 |
| FB Pin Leakage Current | IFB | -100 | | 100 | nA | VIN = 6.5V | 6 |
| Feedback Reference Voltage | VREF | | 0.5 | | V | | 5 |
| UVLO Hysteresis | VUVLO hysteresis | | 150 | | mV | | 5 |
| Line Regulation | ΔVOUT/ΔVIN | | 0.05 | | %/V | IOUT = 5mA, 1.4V ≤ VIN ≤ 6.5V | 5 |
| Load Regulation | ΔVOUT/ΔIOUT | | 0.08 | | %/A | 5mA ≤ IOUT ≤ 3A | 5 |
| Output Noise Voltage 0.5V | eNO | | 7 | | µVRMS | BW = 10Hz to 100kHz, IOUT = 3A, CNR/SS = 100nF, CFF = 10nF, COUT = 22µF, VIN = 1.1V, VOUT = 0.5V | 6 |
| Output Noise Voltage 3.3V | eNO | | 10 | | µVRMS | VOUT = 3.3V | 6 |
| Thermal Shutdown Threshold (increasing) | TSD | | 160 | | °C | Temperature increasing | 7 |
| Thermal Shutdown Threshold (decreasing) | TSD | | 140 | | °C | Temperature decreasing | 7 |
| Abs Max VIN, PGOOD, EN | | -0.3 | | 7 | V | | 5 |
| Abs Max VOUT | | -0.3 | | | V | to (VIN + 0.3V) | 5 |
| Abs Max NR/SS, FB | | -0.3 | | 3.6 | V | | 5 |
| Power Dissipation | PD | | | 3.5 | W | TA = 25°C, WQFN-20L 3.5x3.5 | 5 |
| Lead Temperature | | | | 260 | °C | Soldering, 10 sec | 5 |
| Junction Temperature | TJ | | | 150 | °C | | 5 |
| Storage Temperature | | -65 | | 150 | °C | | 5 |
| ESD HBM | | | | 2 | kV | Human Body Model | 5 |
| ESD CDM | | | | 1 | kV | Charged Device Model | 5 |
| Supply Input Voltage (recommended) | VIN | 1.1 | | 6.5 | V | | 5 |
| Junction Temperature Range (recommended) | TJ | -40 | | 125 | °C | | 5 |
| Thermal Resistance Junction-to-Ambient | θJA | | 28.5 | | °C/W | WQFN-20L 3.5x3.5, JEDEC 51-7 four-layer board, still air, TA = 25°C | 5 |
| Thermal Resistance Junction-to-Case | θJC | | 7.2 | | °C/W | WQFN-20L 3.5x3.5, measured at exposed pad | 5 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | functionality. By connecting these pins to GND, design engineers can extend the GND copper coverage on the PCB top layer to enhance the thermal | 2 |
## CAD (KiCad official)
- Symbol: `RTQ2513TGQW`
- Footprint: `Package_DFN_QFN:QFN-20-1EP_3.5x3.5mm_P0.5mm_EP2x2mm`
- 3D model: VQFN-20(3.5x3.5), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `rtq2513tgqw-etched.step` / `rtq2513tgqw-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `rtq2513tgqw.step` / `rtq2513tgqw.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Richtek Tech datasheet](docs/rtq2513tgqw-datasheet.pdf) (18 pp, sha256 `4e38b49659b0f27b`, retrieved 2026-11-12, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/rtq2513tgqw-datasheet.pdf)