Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

RTQ2513TGQW

Richtek Tech · Linear Voltage Regulators (LDO) · VQFN-20(3.5x3.5)

RTQ2513TGQW from Richtek Tech, in a VQFN-20(3.5x3.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VOUT power_out LDO output pin; requires a 10µF or larger ceramic capacitor (4.7µF or greater effective) placed close to the device for stability.
2 SNS input Output voltage sense input; connect only when setting VOUT by PCB layout, and keep floating if VOUT is set by an external resistor.
3 FB input Feedback voltage input used to set the output voltage via an external resistive divider, with a typical 0.5V reference.
4 PGOOD output Open-drain power-good output, active high when VOUT reaches 88% of target and pulled low on undervoltage, EN shutdown, OCP and OTP.
5 50mV passive Output voltage setting pin; connect to ground to add 50mV to the output voltage, or leave floating if VOUT is set by an external resistor.
6 100mV passive Output voltage setting pin; connect to ground to add 100mV to the output voltage, or leave floating if VOUT is set by an external resistor.
7 200mV passive Output voltage setting pin; connect to ground to add 200mV to the output voltage, or leave floating if VOUT is set by an external resistor.
8 GND power_in Ground pin.
9 400mV passive Output voltage setting pin; connect to ground to add 400mV to the output voltage, or leave floating if VOUT is set by an external resistor.
10 800mV passive Output voltage setting pin; connect to ground to add 800mV to the output voltage, or leave floating if VOUT is set by an external resistor.
11 1.6V passive Output voltage setting pin; connect to ground to add 1.6V to the output voltage, or leave floating if VOUT is set by an external resistor.
12 NC unconnected No internal connection; may be left floating or tied to GND to extend top-layer GND copper for thermal convection.
13 NR/SS passive Noise-reduction and soft-start pin; a capacitor to GND (10nF to 1µF suggested for low noise) reduces output noise and slows the VOUT rise.
14 EN input Enable control input; logic high enables the regulator and driving it low puts the device in shutdown mode.
15 VIN power_in Supply input; place a minimum 22µF ceramic capacitor as close as possible for better noise rejection.
16 VIN power_in Supply input; place a minimum 22µF ceramic capacitor as close as possible for better noise rejection.
17 VIN power_in Supply input; place a minimum 22µF ceramic capacitor as close as possible for better noise rejection.
18 GND power_in Ground pin.
19 VOUT power_out LDO output pin; requires a 10µF or larger ceramic capacitor (4.7µF or greater effective) placed close to the device for stability.
20 VOUT power_out LDO output pin; requires a 10µF or larger ceramic capacitor (4.7µF or greater effective) placed close to the device for stability.
21 GND power_in Exposed pad ground; must be soldered to a large PCB GND area for maximum power dissipation.

Key specifications

Parameter Value
Manufacturer Richtek Tech
Package VQFN-20(3.5x3.5)
Category Power Management
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Operating Input Voltage Range VIN 1.1 6.5 V 5
Under-Voltage Lockout VUVLO 1.02 1.085 V VIN increasing 5
Output Voltage Range (voltage setting pins) VOUT 0.5 3.65 V Using voltage setting pins (50mV, 100mV, 200mV, 400mV, 800mV, and 1.6V) 5
Output Voltage Range (external resistors) VOUT 0.5 5.5 V Using external resistors 5
Output Voltage Accuracy VOUT -1 1 % VIN = VOUT + 0.3V, 0.5V ≤ VOUT ≤ 5.5V, 5mA ≤ IOUT ≤ 3A 5
Dropout Voltage VDROP 110 180 mV VIN = 1.1V to 6.5V, IOUT = 3A, VFB = 0.5V ± 3% 6
Output Current Limit ILIM 3.7 4.2 4.7 A VOUT = 90% VOUT(TARGET), VIN = VOUT(TARGET) + 400mV 6
Ground Pin Current (min load) IGND 2.8 4 mA Minimum load, VIN = 6.5V, IOUT = 5mA 6
Ground Pin Current (max load) IGND 4.2 5.5 mA Maximum load, VIN = 1.4V, IOUT = 3A 6
Ground Pin Current (shutdown) IGND 25 µA Shutdown, PGOOD = Open, VIN = 6.5V, VEN = 0.5V 6
EN Pin Current IEN -0.1 0.1 µA VIN = 6.5V, VEN = 0V and 6.5V 6
EN Pin High-Level Input Voltage VEN_H 1.1 6.5 V Enable device 6
EN Pin Low-Level Input Voltage VEN_L 0 0.5 V Disable device 6
PGOOD Pin Threshold VIT_PGOOD 0.82 0.883 0.93 V PGOOD signal falling with decreasing VOUT (values are multiples of VOUT) 6
PGOOD Pin Low-Level Output Voltage VPGOOD_L 0.4 V VOUT < VIT_PGOOD, IPGOOD = 1mA (current into device) 6
PGOOD Pin Leakage Current IPGOOD_LK 1 µA VOUT > VIT_PGOOD, VPGOOD = 6.5V 6
NR/SS Pin Charging Current INR/SS 4 6.2 9 µA VNR/SS = GND, VIN = 6.5V 6
FB Pin Leakage Current IFB -100 100 nA VIN = 6.5V 6
Feedback Reference Voltage VREF 0.5 V 5
UVLO Hysteresis VUVLO hysteresis 150 mV 5
Line Regulation ΔVOUT/ΔVIN 0.05 %/V IOUT = 5mA, 1.4V ≤ VIN ≤ 6.5V 5
Load Regulation ΔVOUT/ΔIOUT 0.08 %/A 5mA ≤ IOUT ≤ 3A 5
Output Noise Voltage 0.5V eNO 7 µVRMS BW = 10Hz to 100kHz, IOUT = 3A, CNR/SS = 100nF, CFF = 10nF, COUT = 22µF, VIN = 1.1V, VOUT = 0.5V 6
Output Noise Voltage 3.3V eNO 10 µVRMS VOUT = 3.3V 6
Thermal Shutdown Threshold (increasing) TSD 160 °C Temperature increasing 7
Thermal Shutdown Threshold (decreasing) TSD 140 °C Temperature decreasing 7
Abs Max VIN, PGOOD, EN -0.3 7 V 5
Abs Max VOUT -0.3 V to (VIN + 0.3V) 5
Abs Max NR/SS, FB -0.3 3.6 V 5
Power Dissipation PD 3.5 W TA = 25°C, WQFN-20L 3.5x3.5 5
Lead Temperature 260 °C Soldering, 10 sec 5
Junction Temperature TJ 150 °C 5
Storage Temperature -65 150 °C 5
ESD HBM 2 kV Human Body Model 5
ESD CDM 1 kV Charged Device Model 5
Supply Input Voltage (recommended) VIN 1.1 6.5 V 5
Junction Temperature Range (recommended) TJ -40 125 °C 5
Thermal Resistance Junction-to-Ambient θJA 28.5 °C/W WQFN-20L 3.5x3.5, JEDEC 51-7 four-layer board, still air, TA = 25°C 5
Thermal Resistance Junction-to-Case θJC 7.2 °C/W WQFN-20L 3.5x3.5, measured at exposed pad 5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper functionality. By connecting these pins to GND, design engineers can extend the GND copper coverage on the PCB top layer to enhance the thermal 2

CAD (KiCad official)

  • Symbol: RTQ2513TGQW
  • Footprint: Package_DFN_QFN:QFN-20-1EP_3.5x3.5mm_P0.5mm_EP2x2mm
  • 3D model: VQFN-20(3.5x3.5), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: rtq2513tgqw-etched.step / rtq2513tgqw-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); rtq2513tgqw.step / rtq2513tgqw.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Richtek Tech datasheet (18 pp, sha256 4e38b49659b0f27b, retrieved 2026-11-12, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF