main
History Download
Ray Publish 0.1.0 36b0096

RT9525GQW

Richtek Tech · Battery Management ICs · WQFN-16-EP(3x3)

RT9525GQW from Richtek Tech, in a WQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 TS input Thermistor monitor input that connects to the battery NTC to pause charging when the battery is too hot or too cold, and also detects whether the NTC battery is present.
2 BAT bidirectional Battery connect pin, rated for a BAT continuous current of 2.5A total across the two BAT pins.
3 BAT bidirectional Battery connect pin, rated for a BAT continuous current of 2.5A total across the two BAT pins.
4 EN input Active-low charge enable input with a 200k pull-down; the charger turns on when EN is low and EN is pulled low for initial condition.
5 EN2 input Input current limit configuration input; with EN1 it selects 90mA (L,L), 475mA (L,H), 1.5A (H,L), or suspend mode (H,H), and EN2 = L sets VIN regulation range to 4.65V to 6V.
6 EN1 input Input current limit configuration input; with EN2 it selects 90mA (L,L), 475mA (L,H), 1.5A (H,L), or suspend mode (H,H).
7 PGOOD output Active-low, open-drain power good status output that pulls low when VBAT + VOS_H < VIN < VOVP, rated up to 28V with 20mA continuous current.
8 GND power_in Ground pin that must be connected to the GND plane together with the exposed pad for maximum power dissipation.
9 CHG output Active-low, open-drain charger status output that indicates charging, fault (2Hz flash), or charging done states.
10 SYS power_out System connect pin that must be connected to the system load with a minimum 10uF MLCC to GND.
11 SYS power_out System connect pin that must be connected to the system load with a minimum 10uF MLCC to GND.
12 NC unconnected No internal connection.
13 VIN power_in Supply voltage input rated for 28V maximum, with recommended operating range of 4.45V to 6V (EN2 = H, EN1 = L) or 4.65V to 6V (EN2 = L).
14 TIMER passive Safe charge timer setting pin, where the fast charge fault time is tFCHG = 14400 x CTIMER (s) with CTIMER in µF.
15 SYSOFF input System disconnect pin that disconnects SYS from the battery when pulled high and is connected to GND for normal operation, internally pulled up to BAT by a 1µA current source.
16 ISETA passive Charge current set input where resistor RISETA connects between ISETA and GND, setting ICHG_FAST = VISETA / RISETA x 300 (A).
17 GND power_in Exposed thermal pad that must be soldered to a large PCB and connected to GND for maximum power dissipation.

Key specifications

Parameter Value
Manufacturer Richtek Tech
Package WQFN-16-EP(3x3)
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN Operating Range 4.2 6 V 4
VIN Under Voltage Lockout Threshold VUVLO 3.1 3.3 3.5 V 4
VIN Supply Current IIN 1 2 mA ISYS = IBAT = 0mA, EN = L 4
VIN Supply Current IIN 0.8 1.5 mA ISYS = IBAT = 0mA, EN = H 4
VIN Suspend Current ISUS 195 333 A VIN = 5V, EN2 = EN1 = H 4
BAT Sleep Leakage Current ISLEEP 5 15 A VBAT > VIN, (VIN = 0V) 4
VIN - BAT VOS Rising VOS_H 200 300 mV 4
VIN - BAT VOS Falling VOS_L 10 50 mV 4
Battery Regulation Voltage VREG 4.16 4.2 4.23 V 0 to 85°C, ILOAD = 20mA 4
System Regulation Voltage VSYS 5.3 5.5 5.7 V VIN = 6V 4
APPM Regulation Voltage VAPPM 4.2 4.3 4.4 V EN2 = L, EN1 = H 4
DPM Regulation Voltage VDPM 4.35 4.5 4.63 V EN2 = L 4
VIN to VSYS MOSFET Ron RDS(ON) 0.2 0.35 ILIM = 1000mA 4
BAT to VSYS MOSFET Ron RDS(ON) 0.05 0.1 VBAT = 4.2V, ISYS = 1A 5
Re-charge threshold VREGCGG 120 200 280 mV 5
VIN Charge Setting Range ICHG 100 1200 mA 5
VIN Charge Current ICHG 570 600 630 mA VBATT = 4V, RISETA = 1k 5
VIN Current Limit (1.5A mode) ILIM 1.2 1.5 1.8 A EN2 = H, EN1 = L (1.5A mode) 5
VIN Current Limit (500mA mode) ILIM 450 475 500 mA EN2 = L, EN1 = H (500mA mode) 5
VIN Current Limit (100mA mode) ILIM 80 90 100 mA EN2 = L, EN1 = L (100mA mode) 5
BAT Pre-Charge Threshold VPRECH 2.75 2.85 2.95 V BAT Falling 5
Pre-Charge Current IPRECH 5 10 15 % VBAT = 2V 5
Termination Current Ratio to Fast Charge ITERM 10 20 30 % 5
EN, EN1, EN2, SYSOFF Pin Threshold High VIH 1.5 V 5
EN, EN1, EN2, SYSOFF Pin Threshold Low VIL 0.4 V 5
OVP SET Voltage VOVP 6.25 6.5 6.75 V VIN Rising 5
Pre-Charge Fault Time tPCHG 1440 1800 2160 s CTIMER = 1F (1/8 x tFCHG) 5
Fast charge Fault Time tFCHG 11520 14400 17280 s CTIMER = 1F 5
Short Circuit Recovery Time tSHORT_R 64 ms 6
NTC Bias Current INTC 72 75 78 A VIN > UVLO and VIN > VBAT + VOS_H 6
High Temperature Trip Point VHOT 270 300 330 mV VTS Falling 6
Low Temperature Trip Point VCOLD 2000 2100 2200 mV VTS Rising 6
Supply Input Voltage VIN VIN -0.3 28 V 4
CHG, PGOOD Voltage -0.3 28 V 4
Other Pins Voltage -0.3 6 V 4
CHG, PGOOD Continuous Current 20 mA 4
BAT Continuous Current (total in two pins) 2.5 A 4
Power Dissipation WQFN-16L 3x3 PD 1.471 W TA = 25°C 4
Package Thermal Resistance WQFN-16L 3x3 junction-to-ambient θJA 68 °C/W 4
Package Thermal Resistance WQFN-16L 3x3 junction-to-case θJC 7.5 °C/W 4
Lead Temperature (Soldering) 260 °C Soldering, 10 sec. 4
Junction Temperature TJ 150 °C 4
Storage Temperature Range TSTG -65 150 °C 4
ESD Susceptibility HBM 2 kV Human Body Model 4
ESD Susceptibility MM 200 V Machine Model 4
Supply Input Voltage VIN (EN2 = H, EN1 = L) VIN 4.45 6 V EN2 = H, EN1 = L 4
Supply Input Voltage VIN (EN2 = L, EN1 = X) VIN 4.65 6 V EN2 = L, EN1 = X 4
Junction Temperature Range TJ -40 125 °C 4
Ambient Temperature Range TA -40 85 °C 4

CAD (KiCad official)

  • Symbol: RT9525GQW
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: WQFN-16-EP(3x3) (KiCad packages3D, STEP)

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Richtek Tech datasheet (15 pp, sha256 881e29afbb2bbcb2, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF