3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownRT9525GQW
Richtek Tech · Battery Management ICs · WQFN-16-EP(3x3)
RT9525GQW from Richtek Tech, in a WQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TS | input | Thermistor monitor input that connects to the battery NTC to pause charging when the battery is too hot or too cold, and also detects whether the NTC battery is present. |
| 2 | BAT | bidirectional | Battery connect pin, rated for a BAT continuous current of 2.5A total across the two BAT pins. |
| 3 | BAT | bidirectional | Battery connect pin, rated for a BAT continuous current of 2.5A total across the two BAT pins. |
| 4 | EN | input | Active-low charge enable input with a 200k pull-down; the charger turns on when EN is low and EN is pulled low for initial condition. |
| 5 | EN2 | input | Input current limit configuration input; with EN1 it selects 90mA (L,L), 475mA (L,H), 1.5A (H,L), or suspend mode (H,H), and EN2 = L sets VIN regulation range to 4.65V to 6V. |
| 6 | EN1 | input | Input current limit configuration input; with EN2 it selects 90mA (L,L), 475mA (L,H), 1.5A (H,L), or suspend mode (H,H). |
| 7 | PGOOD | output | Active-low, open-drain power good status output that pulls low when VBAT + VOS_H < VIN < VOVP, rated up to 28V with 20mA continuous current. |
| 8 | GND | power_in | Ground pin that must be connected to the GND plane together with the exposed pad for maximum power dissipation. |
| 9 | CHG | output | Active-low, open-drain charger status output that indicates charging, fault (2Hz flash), or charging done states. |
| 10 | SYS | power_out | System connect pin that must be connected to the system load with a minimum 10uF MLCC to GND. |
| 11 | SYS | power_out | System connect pin that must be connected to the system load with a minimum 10uF MLCC to GND. |
| 12 | NC | unconnected | No internal connection. |
| 13 | VIN | power_in | Supply voltage input rated for 28V maximum, with recommended operating range of 4.45V to 6V (EN2 = H, EN1 = L) or 4.65V to 6V (EN2 = L). |
| 14 | TIMER | passive | Safe charge timer setting pin, where the fast charge fault time is tFCHG = 14400 x CTIMER (s) with CTIMER in µF. |
| 15 | SYSOFF | input | System disconnect pin that disconnects SYS from the battery when pulled high and is connected to GND for normal operation, internally pulled up to BAT by a 1µA current source. |
| 16 | ISETA | passive | Charge current set input where resistor RISETA connects between ISETA and GND, setting ICHG_FAST = VISETA / RISETA x 300 (A). |
| 17 | GND | power_in | Exposed thermal pad that must be soldered to a large PCB and connected to GND for maximum power dissipation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Richtek Tech |
| Package | WQFN-16-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Operating Range | 4.2 | 6 | V | 4 | |||
| VIN Under Voltage Lockout Threshold | VUVLO | 3.1 | 3.3 | 3.5 | V | 4 | |
| VIN Supply Current | IIN | 1 | 2 | mA | ISYS = IBAT = 0mA, EN = L | 4 | |
| VIN Supply Current | IIN | 0.8 | 1.5 | mA | ISYS = IBAT = 0mA, EN = H | 4 | |
| VIN Suspend Current | ISUS | 195 | 333 | A | VIN = 5V, EN2 = EN1 = H | 4 | |
| BAT Sleep Leakage Current | ISLEEP | 5 | 15 | A | VBAT > VIN, (VIN = 0V) | 4 | |
| VIN - BAT VOS Rising | VOS_H | 200 | 300 | mV | 4 | ||
| VIN - BAT VOS Falling | VOS_L | 10 | 50 | mV | 4 | ||
| Battery Regulation Voltage | VREG | 4.16 | 4.2 | 4.23 | V | 0 to 85°C, ILOAD = 20mA | 4 |
| System Regulation Voltage | VSYS | 5.3 | 5.5 | 5.7 | V | VIN = 6V | 4 |
| APPM Regulation Voltage | VAPPM | 4.2 | 4.3 | 4.4 | V | EN2 = L, EN1 = H | 4 |
| DPM Regulation Voltage | VDPM | 4.35 | 4.5 | 4.63 | V | EN2 = L | 4 |
| VIN to VSYS MOSFET Ron | RDS(ON) | 0.2 | 0.35 | ILIM = 1000mA | 4 | ||
| BAT to VSYS MOSFET Ron | RDS(ON) | 0.05 | 0.1 | VBAT = 4.2V, ISYS = 1A | 5 | ||
| Re-charge threshold | VREGCGG | 120 | 200 | 280 | mV | 5 | |
| VIN Charge Setting Range | ICHG | 100 | 1200 | mA | 5 | ||
| VIN Charge Current | ICHG | 570 | 600 | 630 | mA | VBATT = 4V, RISETA = 1k | 5 |
| VIN Current Limit (1.5A mode) | ILIM | 1.2 | 1.5 | 1.8 | A | EN2 = H, EN1 = L (1.5A mode) | 5 |
| VIN Current Limit (500mA mode) | ILIM | 450 | 475 | 500 | mA | EN2 = L, EN1 = H (500mA mode) | 5 |
| VIN Current Limit (100mA mode) | ILIM | 80 | 90 | 100 | mA | EN2 = L, EN1 = L (100mA mode) | 5 |
| BAT Pre-Charge Threshold | VPRECH | 2.75 | 2.85 | 2.95 | V | BAT Falling | 5 |
| Pre-Charge Current | IPRECH | 5 | 10 | 15 | % | VBAT = 2V | 5 |
| Termination Current Ratio to Fast Charge | ITERM | 10 | 20 | 30 | % | 5 | |
| EN, EN1, EN2, SYSOFF Pin Threshold High | VIH | 1.5 | V | 5 | |||
| EN, EN1, EN2, SYSOFF Pin Threshold Low | VIL | 0.4 | V | 5 | |||
| OVP SET Voltage | VOVP | 6.25 | 6.5 | 6.75 | V | VIN Rising | 5 |
| Pre-Charge Fault Time | tPCHG | 1440 | 1800 | 2160 | s | CTIMER = 1F (1/8 x tFCHG) | 5 |
| Fast charge Fault Time | tFCHG | 11520 | 14400 | 17280 | s | CTIMER = 1F | 5 |
| Short Circuit Recovery Time | tSHORT_R | 64 | ms | 6 | |||
| NTC Bias Current | INTC | 72 | 75 | 78 | A | VIN > UVLO and VIN > VBAT + VOS_H | 6 |
| High Temperature Trip Point | VHOT | 270 | 300 | 330 | mV | VTS Falling | 6 |
| Low Temperature Trip Point | VCOLD | 2000 | 2100 | 2200 | mV | VTS Rising | 6 |
| Supply Input Voltage VIN | VIN | -0.3 | 28 | V | 4 | ||
| CHG, PGOOD Voltage | -0.3 | 28 | V | 4 | |||
| Other Pins Voltage | -0.3 | 6 | V | 4 | |||
| CHG, PGOOD Continuous Current | 20 | mA | 4 | ||||
| BAT Continuous Current (total in two pins) | 2.5 | A | 4 | ||||
| Power Dissipation WQFN-16L 3x3 | PD | 1.471 | W | TA = 25°C | 4 | ||
| Package Thermal Resistance WQFN-16L 3x3 junction-to-ambient | θJA | 68 | °C/W | 4 | |||
| Package Thermal Resistance WQFN-16L 3x3 junction-to-case | θJC | 7.5 | °C/W | 4 | |||
| Lead Temperature (Soldering) | 260 | °C | Soldering, 10 sec. | 4 | |||
| Junction Temperature | TJ | 150 | °C | 4 | |||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 4 | ||
| ESD Susceptibility HBM | 2 | kV | Human Body Model | 4 | |||
| ESD Susceptibility MM | 200 | V | Machine Model | 4 | |||
| Supply Input Voltage VIN (EN2 = H, EN1 = L) | VIN | 4.45 | 6 | V | EN2 = H, EN1 = L | 4 | |
| Supply Input Voltage VIN (EN2 = L, EN1 = X) | VIN | 4.65 | 6 | V | EN2 = L, EN1 = X | 4 | |
| Junction Temperature Range | TJ | -40 | 125 | °C | 4 | ||
| Ambient Temperature Range | TA | -40 | 85 | °C | 4 |
CAD (KiCad official)
- Symbol:
RT9525GQW - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: WQFN-16-EP(3x3) (KiCad packages3D, STEP)
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Richtek Tech datasheet (15 pp, sha256
881e29afbb2bbcb2, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).