main
Ray
rt9193-30gb: specified limits as data (metadata.characteristics, 29 rows from the datasheet)
9e672a7
RT9193-30GB
Richtek Tech · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SOT-23-5
RT9193-30GB from Richtek Tech, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Power input voltage. Recommended operating range 2.5V to 5.5V (absolute max 6V). Bypass with 1µF X7R ceramic to GND close to the pin. |
| 2 | GND | power_in | Device ground reference for the regulator, EN logic and BP bypass network. |
| 3 | EN | input | Chip Enable, active-high TTL-logic input (VIH ≥ 1.2V, VIL ≤ 0.4V, 0-5.5V range). High-impedance pin (IBSD ≤ 100nA); tie through a 100kΩ pull-down to GND if the drive signal can float. Drive to GND for <0.01µA shutdown. |
| 4 | BP | passive | Reference noise bypass. Connect a 22nF ceramic capacitor between BP and GND for lowest output noise (typ 100µVRMS, 10Hz-100kHz). May be left floating if noise performance is not critical. |
| 5 | VOUT | power_out | Regulated output voltage (3.0V for the -30 option). Delivers up to 300mA with 220mV dropout at 300mA. Requires only 1µF X7R ceramic to GND for stability; low-ESR ceramic capacitors are supported. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Richtek Tech |
| Package | SOT-23-5 |
| Category | PMIC |
| Pins | 5 |
Ordering variants
Same part, different packaging or reel option.
RT9193-30GBBRT9193-30GBU5RT9193-30GBJ5RT9193-30GBQWRT9193-30GBF
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage Accuracy | ΔVOUT | -2 | 2 | % | IOUT = 1mA | 3 | |
| Current Limit | ILIM | 360 | 400 | mA | RLOAD = 1Ω | 3 | |
| Quiescent Current | IQ | 90 | 130 | μA | VEN ≥ 1.2V, IOUT = 0mA | 3 | |
| Dropout Voltage | VDROP | 170 | 200 | mV | IOUT = 200mA, VOUT > 2.8V | 3 | |
| Dropout Voltage | VDROP | 220 | 300 | mV | IOUT = 300mA, VOUT > 2.8V | 3 | |
| Line Regulation | ΔVLINE | 0.3 | % | VIN = (VOUT + 1V) to 5.5V, IOUT = 1mA | 3 | ||
| Load Regulation | ΔVLOAD | 0.6 | % | 1mA < IOUT < 300mA | 3 | ||
| Standby Current | ISTBY | 0.01 | 1 | μA | VEN = GND, Shutdown | 3 | |
| EN Input Bias Current | IIBSD | 0 | 100 | nA | VEN = GND or VIN | 4 | |
| EN Threshold Logic-Low Voltage | VIL | 0.4 | V | VIN = 3V to 5.5V, Shutdown | 4 | ||
| EN Threshold Logic-High Voltage | VIH | 1.2 | V | VIN = 3V to 5.5V, Start-Up | 4 | ||
| Output Noise Voltage | eNO | 100 | μVRMS | 10Hz to 100kHz, IOUT = 200mA, COUT = 1μF | 4 | ||
| Power Supply Rejection Rate | PSRR | -70 | dB | f = 100Hz | 4 | ||
| Power Supply Rejection Rate | PSRR | -50 | dB | f = 10kHz, COUT = 1μF, IOUT = 10mA | 4 | ||
| Thermal Shutdown Temperature | TSD | 165 | °C | 4 | |||
| Thermal Shutdown Temperature (hysteresis) | ΔTSD | 30 | °C | 4 | |||
| Supply Input Voltage | 2.5 | 5.5 | V | 3 | |||
| EN Input Voltage | 0 | 5.5 | V | 3 | |||
| Junction Temperature Range | -40 | 125 | °C | 3 | |||
| Ambient Temperature Range | -40 | 85 | °C | 3 | |||
| Supply Input Voltage | 6 | V | 3 | ||||
| Power Dissipation, TSOT-23-5/SOT-23-5 | PD | 400 | mW | TA = 25°C | 3 | ||
| Junction Temperature | 150 | °C | 3 | ||||
| Lead Temperature (Soldering) | 260 | °C | 10 sec | 3 | |||
| Storage Temperature Range | -65 | 150 | °C | 3 | |||
| ESD Susceptibility HBM | 2 | kV | Human Body Model | 3 | |||
| ESD Susceptibility MM | 200 | V | Machine Model | 3 | |||
| Package Thermal Resistance, TSOT-23-5/SOT-23-5 junction-to-ambient | θJA | 250 | °C/W | 3 | |||
| Package Thermal Resistance, TSOT-23-5/SOT-23-5 junction-to-case | θJC | 25 | °C/W | 3 |
CAD (KiCad official)
- Symbol:
RT9193-30GB - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-23-5 (KiCad packages3D, STEP)
- 3D model files:
rt9193-30gb-etched.step/rt9193-30gb-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);rt9193-30gb.step/rt9193-30gb.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Richtek Tech datasheet (14 pp, sha256
f6d2d8e81d3754fc, retrieved 2026-08-17, tier: manufacturer) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# RT9193-30GB
**Richtek Tech** · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SOT-23-5
RT9193-30GB from Richtek Tech, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Power input voltage. Recommended operating range 2.5V to 5.5V (absolute max 6V). Bypass with 1µF X7R ceramic to GND close to the pin. |
| 2 | GND | power_in | Device ground reference for the regulator, EN logic and BP bypass network. |
| 3 | EN | input | Chip Enable, active-high TTL-logic input (VIH ≥ 1.2V, VIL ≤ 0.4V, 0-5.5V range). High-impedance pin (IBSD ≤ 100nA); tie through a 100kΩ pull-down to GND if the drive signal can float. Drive to GND for <0.01µA shutdown. |
| 4 | BP | passive | Reference noise bypass. Connect a 22nF ceramic capacitor between BP and GND for lowest output noise (typ 100µVRMS, 10Hz-100kHz). May be left floating if noise performance is not critical. |
| 5 | VOUT | power_out | Regulated output voltage (3.0V for the -30 option). Delivers up to 300mA with 220mV dropout at 300mA. Requires only 1µF X7R ceramic to GND for stability; low-ESR ceramic capacitors are supported. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Richtek Tech |
| Package | SOT-23-5 |
| Category | PMIC |
| Pins | 5 |
## Ordering variants
Same part, different packaging or reel option.
- `RT9193-30GBB`
- `RT9193-30GBU5`
- `RT9193-30GBJ5`
- `RT9193-30GBQW`
- `RT9193-30GBF`
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage Accuracy | ΔVOUT | -2 | | 2 | % | IOUT = 1mA | 3 |
| Current Limit | ILIM | 360 | 400 | | mA | RLOAD = 1Ω | 3 |
| Quiescent Current | IQ | | 90 | 130 | μA | VEN ≥ 1.2V, IOUT = 0mA | 3 |
| Dropout Voltage | VDROP | | 170 | 200 | mV | IOUT = 200mA, VOUT > 2.8V | 3 |
| Dropout Voltage | VDROP | | 220 | 300 | mV | IOUT = 300mA, VOUT > 2.8V | 3 |
| Line Regulation | ΔVLINE | | | 0.3 | % | VIN = (VOUT + 1V) to 5.5V, IOUT = 1mA | 3 |
| Load Regulation | ΔVLOAD | | | 0.6 | % | 1mA < IOUT < 300mA | 3 |
| Standby Current | ISTBY | | 0.01 | 1 | μA | VEN = GND, Shutdown | 3 |
| EN Input Bias Current | IIBSD | | 0 | 100 | nA | VEN = GND or VIN | 4 |
| EN Threshold Logic-Low Voltage | VIL | | | 0.4 | V | VIN = 3V to 5.5V, Shutdown | 4 |
| EN Threshold Logic-High Voltage | VIH | 1.2 | | | V | VIN = 3V to 5.5V, Start-Up | 4 |
| Output Noise Voltage | eNO | | 100 | | μVRMS | 10Hz to 100kHz, IOUT = 200mA, COUT = 1μF | 4 |
| Power Supply Rejection Rate | PSRR | | -70 | | dB | f = 100Hz | 4 |
| Power Supply Rejection Rate | PSRR | | -50 | | dB | f = 10kHz, COUT = 1μF, IOUT = 10mA | 4 |
| Thermal Shutdown Temperature | TSD | | 165 | | °C | | 4 |
| Thermal Shutdown Temperature (hysteresis) | ΔTSD | | 30 | | °C | | 4 |
| Supply Input Voltage | | 2.5 | | 5.5 | V | | 3 |
| EN Input Voltage | | 0 | | 5.5 | V | | 3 |
| Junction Temperature Range | | -40 | | 125 | °C | | 3 |
| Ambient Temperature Range | | -40 | | 85 | °C | | 3 |
| Supply Input Voltage | | | | 6 | V | | 3 |
| Power Dissipation, TSOT-23-5/SOT-23-5 | PD | | | 400 | mW | TA = 25°C | 3 |
| Junction Temperature | | | | 150 | °C | | 3 |
| Lead Temperature (Soldering) | | | | 260 | °C | 10 sec | 3 |
| Storage Temperature Range | | -65 | | 150 | °C | | 3 |
| ESD Susceptibility HBM | | | | 2 | kV | Human Body Model | 3 |
| ESD Susceptibility MM | | | | 200 | V | Machine Model | 3 |
| Package Thermal Resistance, TSOT-23-5/SOT-23-5 junction-to-ambient | θJA | | 250 | | °C/W | | 3 |
| Package Thermal Resistance, TSOT-23-5/SOT-23-5 junction-to-case | θJC | | 25 | | °C/W | | 3 |
## CAD (KiCad official)
- Symbol: `RT9193-30GB`
- Footprint: `Package_TO_SOT_SMD:SOT-23-5`
- 3D model: SOT-23-5 (KiCad packages3D, STEP)
- 3D model files: `rt9193-30gb-etched.step` / `rt9193-30gb-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `rt9193-30gb.step` / `rt9193-30gb.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Richtek Tech datasheet](docs/rt9193-30gb-datasheet.pdf) (14 pp, sha256 `f6d2d8e81d3754fc`, retrieved 2026-08-17, tier: manufacturer)
- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/rt9193-30gb-datasheet.pdf)