main
Ray
Publish 0.1.0
d346dd7
RT9088AGQW
Richtek Tech · Pre-ordered Chips · WDFN-10L-EP(3x3)
RT9088AGQW from Richtek Tech, in a WDFN-10L-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | REFIN | input | Reference input, with a stated voltage range of 0.5V to 1.8V and an under-voltage lockout threshold of 360 to 420 mV on REFIN rising. |
| 2 | VIN | power_in | Power input of the regulator, with a supply input voltage range of 1.1V to 3.5V. |
| 3 | VOUT | power_out | Power output of the regulator, which tracks REFIN through the SENSE feedback, with a source and sink current limit of 3.5A to 5.5A when VOUT is in the PGOOD window. |
| 4 | PGND | power_in | Power ground of the regulator, which carries the output source and sink current. |
| 5 | SENSE | input | Voltage sense input for the regulator; connect to the positive terminal of the output capacitor or the load. |
| 6 | REFOUT | output | Reference output equal to REFIN with 10mA source and sink capability; connect to GND through a ceramic capacitor (printed as 0.1F in the pin table and 0.1μF in the application circuit). |
| 7 | EN | input | Enable control input; connect to SLP_S3 for DDR VTT applications, otherwise use as ON/OFF, with logic-high at 1.7V minimum and logic-low at 0.3V maximum. |
| 8 | GND | power_in | Analog ground; connect to the negative terminal of the output capacitor. |
| 9 | PGOOD | output | Power good open-drain output; connect a pull-up resistor between this pin and VCNTL, with output low voltage of 0.4V maximum at 4mA. |
| 10 | VCNTL | power_in | Control voltage input, connected to a 3.3V or 5V supply within a VCNTL input voltage range of 2.9V to 5.5V, with a 4.7μF ceramic decoupling capacitor required. |
| 11 | PAD | passive | Exposed pad, internally unconnected, which must be soldered to a large PGND plane with thermal vias to help dissipate heat. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Richtek Tech |
| Package | WDFN-10L-EP(3x3) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Control Input Voltage | VCNTL | 2.9 | 5.5 | V | 4 | ||
| Supply Input Voltage | VIN | 1.1 | 3.5 | V | 4 | ||
| Junction Temperature Range | TJ | -40 | 125 | °C | 4 | ||
| Ambient Temperature Range | TA | -40 | 85 | °C | 4 | ||
| Supply Voltage | VIN, VCNTL | -0.3 | 6 | V | 4 | ||
| Input Voltage | EN, REFIN, SENSE | -0.3 | 6 | V | 4 | ||
| Output Voltage | VOUT, REFOUT, PGOOD | -0.3 | 6 | V | 4 | ||
| Power Dissipation | PD | 3.27 | W | TA = 25°C, WDFN-10L 3x3 | 4 | ||
| Package Thermal Resistance, junction to ambient | θJA | 30.5 | °C/W | WDFN-10L 3x3, four-layer JEDEC 51-7 board, TA = 25°C | 4 | ||
| Package Thermal Resistance, junction to case | θJC | 7.5 | °C/W | WDFN-10L 3x3, measured at exposed pad | 4 | ||
| Lead Temperature (Soldering, 10 sec.) | 260 | °C | Soldering, 10 sec. | 4 | |||
| Junction Temperature | TJ | 150 | °C | 4 | |||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 4 | ||
| ESD Susceptibility HBM | 2 | kV | Human Body Model | 4 | |||
| VCNTL Supply Current | IVCNTL | 0.7 | 1 | mA | VEN = VCNTL, No Load | 4 | |
| VCNTL Supply Current | 65 | 80 | μA | VEN = 0V, VREFIN = 0V, No Load | 4 | ||
| VCNTL Shutdown Current | ISHDN_VCNTL | 200 | 400 | μA | VEN = 0V, VREFIN > 0.4V, No Load | 4 | |
| VIN Supply Current | IVIN | 1 | 50 | μA | VEN = VCNTL, No Load | 4 | |
| VIN Shutdown Current | ISHDN_VIN | 0.1 | 50 | μA | VEN = 0V, No Load | 4 | |
| REFIN, VTT Output Voltage Offset | VOUT_OS | 25 | 25 | mV | IOUT = ±2A, VLDOIN = 1.5V, VREFOUT = 0.75V | 4 | |
| VOUT Source Current Limit | ILIM_VOUT_SR | 3.5 | 5.5 | A | VOUT in PGOOD Window | 5 | |
| VOUT Sink Current Limit | ILIM_VOUT_SK | 3.5 | 5.5 | A | VOUT in PGOOD Window | 5 | |
| VOUT Discharge Resistance | RDISCHARGE | 18 | 25 | VREFIN = 0V, VOUT = 0.3V, VEN = 0V | 5 | ||
| PGOOD Threshold, VSENSE lower threshold | VTH_PGOOD | 25 | 20 | 15 | % | VSENSE lower threshold with respect to REFOUT | 5 |
| PGOOD Threshold, VSENSE upper threshold | VTH_PGOOD | 15 | 20 | 25 | % | VSENSE upper threshold with respect to REFOUT | 5 |
| Output Low Voltage | VLOW_PGOOD | 0.4 | V | IPGOOD = 4mA | 5 | ||
| Leakage Current | ILEAKAGE_PGOOD | 1 | μA | VSENSE = VREFIN (PGOOD high impedance), VPGOOD = VIN + 0.3V | 5 | ||
| REFIN Input Current | IREFIN | 1 | μA | VEN = VCNTL | 5 | ||
| REFIN Voltage Range | VREFIN | 0.5 | 1.8 | V | 5 | ||
| REFIN Under-Voltage Lockout, REFIN Rising | VUVLO_REFIN | 360 | 390 | 420 | mV | REFIN Rising | 5 |
| REFOUT Voltage Tolerance to VREFIN | VTOL_REFOUT | 15 | 15 | mV | 10mA < IREFOUT < 10mA, VREFIN = 0.75V | 5 | |
| REFOUT Source Current Limit | ILIM_REFOUT_SR | 10 | 40 | mA | VREFOUT = 0V | 5 | |
| REFOUT Sink Current Limit | ILIM_REFOUT_SK | 10 | 40 | mA | VREFOUT = REFIN + 1V | 5 | |
| UVLO Threshold, Rising | VUVLO_VCNTL | 2.5 | 2.7 | 2.85 | V | Rising | 5 |
| EN Input Voltage Logic-High | VIN_H | 1.7 | V | 5 | |||
| EN Input Voltage Logic-Low | VIN_L | 0.3 | V | 5 | |||
| EN Turn-On Delay | tDELAY | 7 | μs | EN turn on to VOUT rising (reference Note 5) | 5 |
CAD (KiCad official)
- Symbol:
RT9088AGQW - Footprint:
Package_DFN_QFN:WDFN-10-1EP_3x3mm_P0.5mm_EP1.8x2.5mm - 3D model: WDFN-10L-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
rt9088agqw-etched.step/rt9088agqw-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);rt9088agqw.step/rt9088agqw.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Richtek Tech datasheet (11 pp, sha256
ed0141c42b273f2d, retrieved 2026-11-05, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# RT9088AGQW
**Richtek Tech** · Pre-ordered Chips · WDFN-10L-EP(3x3)
RT9088AGQW from Richtek Tech, in a WDFN-10L-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | REFIN | input | Reference input, with a stated voltage range of 0.5V to 1.8V and an under-voltage lockout threshold of 360 to 420 mV on REFIN rising. |
| 2 | VIN | power_in | Power input of the regulator, with a supply input voltage range of 1.1V to 3.5V. |
| 3 | VOUT | power_out | Power output of the regulator, which tracks REFIN through the SENSE feedback, with a source and sink current limit of 3.5A to 5.5A when VOUT is in the PGOOD window. |
| 4 | PGND | power_in | Power ground of the regulator, which carries the output source and sink current. |
| 5 | SENSE | input | Voltage sense input for the regulator; connect to the positive terminal of the output capacitor or the load. |
| 6 | REFOUT | output | Reference output equal to REFIN with 10mA source and sink capability; connect to GND through a ceramic capacitor (printed as 0.1F in the pin table and 0.1μF in the application circuit). |
| 7 | EN | input | Enable control input; connect to SLP_S3 for DDR VTT applications, otherwise use as ON/OFF, with logic-high at 1.7V minimum and logic-low at 0.3V maximum. |
| 8 | GND | power_in | Analog ground; connect to the negative terminal of the output capacitor. |
| 9 | PGOOD | output | Power good open-drain output; connect a pull-up resistor between this pin and VCNTL, with output low voltage of 0.4V maximum at 4mA. |
| 10 | VCNTL | power_in | Control voltage input, connected to a 3.3V or 5V supply within a VCNTL input voltage range of 2.9V to 5.5V, with a 4.7μF ceramic decoupling capacitor required. |
| 11 | PAD | passive | Exposed pad, internally unconnected, which must be soldered to a large PGND plane with thermal vias to help dissipate heat. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Richtek Tech |
| Package | WDFN-10L-EP(3x3) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 11 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Control Input Voltage | VCNTL | 2.9 | | 5.5 | V | | 4 |
| Supply Input Voltage | VIN | 1.1 | | 3.5 | V | | 4 |
| Junction Temperature Range | TJ | -40 | | 125 | °C | | 4 |
| Ambient Temperature Range | TA | -40 | | 85 | °C | | 4 |
| Supply Voltage | VIN, VCNTL | -0.3 | | 6 | V | | 4 |
| Input Voltage | EN, REFIN, SENSE | -0.3 | | 6 | V | | 4 |
| Output Voltage | VOUT, REFOUT, PGOOD | -0.3 | | 6 | V | | 4 |
| Power Dissipation | PD | | | 3.27 | W | TA = 25°C, WDFN-10L 3x3 | 4 |
| Package Thermal Resistance, junction to ambient | θJA | | 30.5 | | °C/W | WDFN-10L 3x3, four-layer JEDEC 51-7 board, TA = 25°C | 4 |
| Package Thermal Resistance, junction to case | θJC | | 7.5 | | °C/W | WDFN-10L 3x3, measured at exposed pad | 4 |
| Lead Temperature (Soldering, 10 sec.) | | | | 260 | °C | Soldering, 10 sec. | 4 |
| Junction Temperature | TJ | | | 150 | °C | | 4 |
| Storage Temperature Range | TSTG | -65 | | 150 | °C | | 4 |
| ESD Susceptibility HBM | | | 2 | | kV | Human Body Model | 4 |
| VCNTL Supply Current | IVCNTL | | 0.7 | 1 | mA | VEN = VCNTL, No Load | 4 |
| VCNTL Supply Current | | | 65 | 80 | μA | VEN = 0V, VREFIN = 0V, No Load | 4 |
| VCNTL Shutdown Current | ISHDN_VCNTL | | 200 | 400 | μA | VEN = 0V, VREFIN > 0.4V, No Load | 4 |
| VIN Supply Current | IVIN | | 1 | 50 | μA | VEN = VCNTL, No Load | 4 |
| VIN Shutdown Current | ISHDN_VIN | | 0.1 | 50 | μA | VEN = 0V, No Load | 4 |
| REFIN, VTT Output Voltage Offset | VOUT_OS | 25 | | 25 | mV | IOUT = ±2A, VLDOIN = 1.5V, VREFOUT = 0.75V | 4 |
| VOUT Source Current Limit | ILIM_VOUT_SR | 3.5 | | 5.5 | A | VOUT in PGOOD Window | 5 |
| VOUT Sink Current Limit | ILIM_VOUT_SK | 3.5 | | 5.5 | A | VOUT in PGOOD Window | 5 |
| VOUT Discharge Resistance | RDISCHARGE | | 18 | 25 | | VREFIN = 0V, VOUT = 0.3V, VEN = 0V | 5 |
| PGOOD Threshold, VSENSE lower threshold | VTH_PGOOD | 25 | 20 | 15 | % | VSENSE lower threshold with respect to REFOUT | 5 |
| PGOOD Threshold, VSENSE upper threshold | VTH_PGOOD | 15 | 20 | 25 | % | VSENSE upper threshold with respect to REFOUT | 5 |
| Output Low Voltage | VLOW_PGOOD | | | 0.4 | V | IPGOOD = 4mA | 5 |
| Leakage Current | ILEAKAGE_PGOOD | | | 1 | μA | VSENSE = VREFIN (PGOOD high impedance), VPGOOD = VIN + 0.3V | 5 |
| REFIN Input Current | IREFIN | | | 1 | μA | VEN = VCNTL | 5 |
| REFIN Voltage Range | VREFIN | 0.5 | | 1.8 | V | | 5 |
| REFIN Under-Voltage Lockout, REFIN Rising | VUVLO_REFIN | 360 | 390 | 420 | mV | REFIN Rising | 5 |
| REFOUT Voltage Tolerance to VREFIN | VTOL_REFOUT | 15 | | 15 | mV | 10mA < IREFOUT < 10mA, VREFIN = 0.75V | 5 |
| REFOUT Source Current Limit | ILIM_REFOUT_SR | 10 | 40 | | mA | VREFOUT = 0V | 5 |
| REFOUT Sink Current Limit | ILIM_REFOUT_SK | 10 | 40 | | mA | VREFOUT = REFIN + 1V | 5 |
| UVLO Threshold, Rising | VUVLO_VCNTL | 2.5 | 2.7 | 2.85 | V | Rising | 5 |
| EN Input Voltage Logic-High | VIN_H | 1.7 | | | V | | 5 |
| EN Input Voltage Logic-Low | VIN_L | | | 0.3 | V | | 5 |
| EN Turn-On Delay | tDELAY | | | 7 | μs | EN turn on to VOUT rising (reference Note 5) | 5 |
## CAD (KiCad official)
- Symbol: `RT9088AGQW`
- Footprint: `Package_DFN_QFN:WDFN-10-1EP_3x3mm_P0.5mm_EP1.8x2.5mm`
- 3D model: WDFN-10L-EP(3x3) (KiCad packages3D, STEP)
- 3D model files: `rt9088agqw-etched.step` / `rt9088agqw-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `rt9088agqw.step` / `rt9088agqw.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Richtek Tech datasheet](docs/rt9088agqw-datasheet.pdf) (11 pp, sha256 `ed0141c42b273f2d`, retrieved 2026-11-05, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/rt9088agqw-datasheet.pdf)