Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

RT9088AGQW

Richtek Tech · Pre-ordered Chips · WDFN-10L-EP(3x3)

RT9088AGQW from Richtek Tech, in a WDFN-10L-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 REFIN input Reference input, with a stated voltage range of 0.5V to 1.8V and an under-voltage lockout threshold of 360 to 420 mV on REFIN rising.
2 VIN power_in Power input of the regulator, with a supply input voltage range of 1.1V to 3.5V.
3 VOUT power_out Power output of the regulator, which tracks REFIN through the SENSE feedback, with a source and sink current limit of 3.5A to 5.5A when VOUT is in the PGOOD window.
4 PGND power_in Power ground of the regulator, which carries the output source and sink current.
5 SENSE input Voltage sense input for the regulator; connect to the positive terminal of the output capacitor or the load.
6 REFOUT output Reference output equal to REFIN with 10mA source and sink capability; connect to GND through a ceramic capacitor (printed as 0.1F in the pin table and 0.1μF in the application circuit).
7 EN input Enable control input; connect to SLP_S3 for DDR VTT applications, otherwise use as ON/OFF, with logic-high at 1.7V minimum and logic-low at 0.3V maximum.
8 GND power_in Analog ground; connect to the negative terminal of the output capacitor.
9 PGOOD output Power good open-drain output; connect a pull-up resistor between this pin and VCNTL, with output low voltage of 0.4V maximum at 4mA.
10 VCNTL power_in Control voltage input, connected to a 3.3V or 5V supply within a VCNTL input voltage range of 2.9V to 5.5V, with a 4.7μF ceramic decoupling capacitor required.
11 PAD passive Exposed pad, internally unconnected, which must be soldered to a large PGND plane with thermal vias to help dissipate heat.

Key specifications

Parameter Value
Manufacturer Richtek Tech
Package WDFN-10L-EP(3x3)
Category Communication Interface Chip/UART/485/232
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Control Input Voltage VCNTL 2.9 5.5 V 4
Supply Input Voltage VIN 1.1 3.5 V 4
Junction Temperature Range TJ -40 125 °C 4
Ambient Temperature Range TA -40 85 °C 4
Supply Voltage VIN, VCNTL -0.3 6 V 4
Input Voltage EN, REFIN, SENSE -0.3 6 V 4
Output Voltage VOUT, REFOUT, PGOOD -0.3 6 V 4
Power Dissipation PD 3.27 W TA = 25°C, WDFN-10L 3x3 4
Package Thermal Resistance, junction to ambient θJA 30.5 °C/W WDFN-10L 3x3, four-layer JEDEC 51-7 board, TA = 25°C 4
Package Thermal Resistance, junction to case θJC 7.5 °C/W WDFN-10L 3x3, measured at exposed pad 4
Lead Temperature (Soldering, 10 sec.) 260 °C Soldering, 10 sec. 4
Junction Temperature TJ 150 °C 4
Storage Temperature Range TSTG -65 150 °C 4
ESD Susceptibility HBM 2 kV Human Body Model 4
VCNTL Supply Current IVCNTL 0.7 1 mA VEN = VCNTL, No Load 4
VCNTL Supply Current 65 80 μA VEN = 0V, VREFIN = 0V, No Load 4
VCNTL Shutdown Current ISHDN_VCNTL 200 400 μA VEN = 0V, VREFIN > 0.4V, No Load 4
VIN Supply Current IVIN 1 50 μA VEN = VCNTL, No Load 4
VIN Shutdown Current ISHDN_VIN 0.1 50 μA VEN = 0V, No Load 4
REFIN, VTT Output Voltage Offset VOUT_OS 25 25 mV IOUT = ±2A, VLDOIN = 1.5V, VREFOUT = 0.75V 4
VOUT Source Current Limit ILIM_VOUT_SR 3.5 5.5 A VOUT in PGOOD Window 5
VOUT Sink Current Limit ILIM_VOUT_SK 3.5 5.5 A VOUT in PGOOD Window 5
VOUT Discharge Resistance RDISCHARGE 18 25 VREFIN = 0V, VOUT = 0.3V, VEN = 0V 5
PGOOD Threshold, VSENSE lower threshold VTH_PGOOD 25 20 15 % VSENSE lower threshold with respect to REFOUT 5
PGOOD Threshold, VSENSE upper threshold VTH_PGOOD 15 20 25 % VSENSE upper threshold with respect to REFOUT 5
Output Low Voltage VLOW_PGOOD 0.4 V IPGOOD = 4mA 5
Leakage Current ILEAKAGE_PGOOD 1 μA VSENSE = VREFIN (PGOOD high impedance), VPGOOD = VIN + 0.3V 5
REFIN Input Current IREFIN 1 μA VEN = VCNTL 5
REFIN Voltage Range VREFIN 0.5 1.8 V 5
REFIN Under-Voltage Lockout, REFIN Rising VUVLO_REFIN 360 390 420 mV REFIN Rising 5
REFOUT Voltage Tolerance to VREFIN VTOL_REFOUT 15 15 mV 10mA < IREFOUT < 10mA, VREFIN = 0.75V 5
REFOUT Source Current Limit ILIM_REFOUT_SR 10 40 mA VREFOUT = 0V 5
REFOUT Sink Current Limit ILIM_REFOUT_SK 10 40 mA VREFOUT = REFIN + 1V 5
UVLO Threshold, Rising VUVLO_VCNTL 2.5 2.7 2.85 V Rising 5
EN Input Voltage Logic-High VIN_H 1.7 V 5
EN Input Voltage Logic-Low VIN_L 0.3 V 5
EN Turn-On Delay tDELAY 7 μs EN turn on to VOUT rising (reference Note 5) 5

CAD (KiCad official)

  • Symbol: RT9088AGQW
  • Footprint: Package_DFN_QFN:WDFN-10-1EP_3x3mm_P0.5mm_EP1.8x2.5mm
  • 3D model: WDFN-10L-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: rt9088agqw-etched.step / rt9088agqw-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); rt9088agqw.step / rt9088agqw.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Richtek Tech datasheet (11 pp, sha256 ed0141c42b273f2d, retrieved 2026-11-05, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF