main
Ray
Publish 0.1.0
0f9c886
RT8532GQW
Richtek Tech · LED Drivers · WQFN-20-EP(3x3)
RT8532GQW from Richtek Tech, in a WQFN-20-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Chip enable, active high, with an internal 400k pull-low resistor; input high is 1.3V to 24V and low is up to 0.5V. |
| 2 | FREQ | passive | Boost switching frequency setting; connect a resistor between this pin and AGND (22k gives 1MHz, 51k gives 0.5MHz typ). |
| 3 | ISET | passive | LED current setting; a resistor RISET from ISET to ground sets ILED = 240/RISET (kΩ) mA. |
| 4 | MIX | input | Dimming mode selection with internal 400k pull-up to VDC; floating or high gives 25% mixed mode dimming, low gives direct PWM mode dimming. |
| 5 | AGND | power_in | Analog ground of the LED driver. |
| 6 | LED6 | passive | Current sink for LED string 6; leave unconnected or short to GND if not used. |
| 7 | LED5 | passive | Current sink for LED string 5; leave unconnected or short to GND if not used. |
| 8 | LED4 | passive | Current sink for LED string 4; leave unconnected or short to GND if not used. |
| 9 | LED3 | passive | Current sink for LED string 3; leave unconnected or short to GND if not used. |
| 10 | LED2 | passive | Current sink for LED string 2; leave unconnected or short to GND if not used. |
| 11 | LED1 | passive | Current sink for LED string 1; leave unconnected or short to GND if not used. |
| 12 | OVP | input | Over voltage protection sense input with a detecting threshold of 1.2V (typ.). |
| 13 | PGND | power_in | Power ground of the boost converter (pins 13 and 14). |
| 14 | PGND | power_in | Power ground of the boost converter (pins 13 and 14). |
| 15 | LX | passive | Switching pin of the boost converter (pins 15 and 16); internal 200mΩ, 43V power switch with 2.5A typ. current limit. |
| 16 | LX | passive | Switching pin of the boost converter (pins 15 and 16); internal 200mΩ, 43V power switch with 2.5A typ. current limit. |
| 17 | PWM | input | PWM dimming control input; high is 1.3V to 24V, low up to 0.5V, dimming frequency 100Hz to 20kHz. |
| 18 | VDC | power_out | Internal regulator voltage (3.6V to 4V, 3.8V typ.); connect a capacitor from this pin to ground. |
| 19 | VIN | power_in | Power supply input, 2.5V to 24V operating range. |
| 20 | COMP | passive | Compensation node of the boost converter; connect a compensation network for stability. |
| 21 | GND | power_in | Exposed pad ground; must be soldered to a large PCB and connected to GND for maximum power dissipation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Richtek Tech |
| Package | WQFN-20-EP(3x3) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Input Voltage | VIN | 2.5 | 24 | V | 4 | ||
| Junction Temperature Range | TJ | -40 | 125 | °C | 4 | ||
| Ambient Temperature Range | TA | -40 | 85 | °C | 4 | ||
| Supply Input Voltage to GND | VIN | -0.3 | 26.5 | V | 4 | ||
| EN, PWM, ISET, COMP, MIX, FREQ to GND | -0.3 | 26.5 | V | 4 | |||
| LX, OVP, LED1 to LED6 to GND | -0.3 | 48 | V | 4 | |||
| LX to GND | -0.3 | 48 | V | 4 | |||
| LX to GND transient | -1 | 48 | V | < 500ns | 4 | ||
| VDC to GND | -0.3 | 7 | V | 4 | |||
| Power Dissipation | PD | 1.471 | W | WQFN-20L 3x3, TA = 25°C | 4 | ||
| Junction Temperature | TJ | 150 | °C | 4 | |||
| Storage Temperature Range | -65 | 150 | °C | 4 | |||
| Lead Temperature | 260 | °C | Soldering, 10 sec. | 4 | |||
| ESD HBM | 2 | kV | 4 | ||||
| ESD MM | 200 | V | 4 | ||||
| Thermal Resistance Junction-to-Ambient | θJA | 68 | °C/W | WQFN-20L 3x3 | 4 | ||
| Thermal Resistance Junction-to-Case | θJC | 7.5 | °C/W | WQFN-20L 3x3 | 4 | ||
| VIN Shutdown Current | ISHDN | 10 | A | VIN = 4.5V, EN = 0V | 4 | ||
| PWM Dimming Frequency | fPWM | 0.1 | 20 | kHz | 4 | ||
| EN, PWM Input High Voltage | VIH | 1.3 | 24 | V | VIN = 2.5V to 24V | 4 | |
| EN, PWM Input Low Voltage | VIL | 0.5 | V | VIN = 2.5V to 24V | 4 | ||
| Switching Frequency | fSW | 0.8 | 1 | 1.2 | MHz | RFSW = 22k | 4 |
| Switching Frequency | fSW | 0.4 | 0.5 | 0.6 | MHz | RFSW = 51k | 4 |
| LX On Resistance (N-MOSFET) | RLX | 0.18 | 0.2 | 0.22 | Ω | VIN > 4.5V | 4 |
| Minimum On-Time | tON(MIN) | 40 | 60 | 80 | ns | FSW = 1MHz | 5 |
| Maximum Duty | DMAX | 90 | 93 | 96 | % | FSW = 1MHz | 5 |
| LX Current Limit | ILIM | 2.2 | 2.5 | 2.8 | A | 5 | |
| Regulated VLEDx | VLEDx | 0.5 | 0.6 | 0.7 | V | Highest LED string, ILED = 20mA | 5 |
| LDO Output Voltage Range | VDC | 3.6 | 3.8 | 4 | V | 5 | |
| Maximum LED Current | IFB(MAX) | 5 | 50 | mA | MODE = PWM Mode | 5 | |
| Maximum LED Current | IFB(MAX) | 8 | 50 | mA | MODE = Mixed Mode | 5 | |
| LED Current Accuracy | ILEDA | 19.4 | 20 | 20.6 | mA | 2V > VLEDx > 0.5V, RISET = 12k | 5 |
| LED Current Matching | ILEDM | 2 | % | 2V > VLEDx > 0.5V, RISET = 12k | 5 | ||
| ISET Pin Voltage | VISET | 0.76 | 1 | 1.24 | V | 5 | |
| OVP Threshold | VOVP | 1.16 | 1.2 | 1.24 | V | 5 | |
| VIN Quiescent Current | IVIN | 3 | mA | PWM = COMP = 0V, not switching | 4 | ||
| VIN Quiescent Current (switching) | IVIN_SW | 4 | mA | PWM = COMP = 2V, switching | 4 | ||
| VIN UVLO Threshold rising | VUVLO | 2.3 | V | VIN rising | 4 | ||
| VIN UVLO Threshold falling | VUVLO | 2.1 | V | VIN falling | 4 | ||
| OVP UVLO Threshold | VOVPF | 50 | mV | 5 | |||
| Thermal Shutdown Temperature | TSD | 150 | C | 5 | |||
| OTP Hysteresis | TOTP_Hys | 30 | C | 5 | |||
| LED Pin Under Voltage Threshold | VLSD | 0.1 | V | Un-Connection | 5 |
CAD (KiCad official)
- Symbol:
RT8532GQW - Footprint:
Package_DFN_QFN:UQFN-20-1EP_3x3mm_P0.4mm_EP1.85x1.85mm - 3D model: WQFN-20-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
rt8532gqw-etched.step/rt8532gqw-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);rt8532gqw.step/rt8532gqw.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Richtek Tech datasheet (14 pp, sha256
a756183a9ce08327, retrieved 2026-10-23, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# RT8532GQW
**Richtek Tech** · LED Drivers · WQFN-20-EP(3x3)
RT8532GQW from Richtek Tech, in a WQFN-20-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Chip enable, active high, with an internal 400k pull-low resistor; input high is 1.3V to 24V and low is up to 0.5V. |
| 2 | FREQ | passive | Boost switching frequency setting; connect a resistor between this pin and AGND (22k gives 1MHz, 51k gives 0.5MHz typ). |
| 3 | ISET | passive | LED current setting; a resistor RISET from ISET to ground sets ILED = 240/RISET (kΩ) mA. |
| 4 | MIX | input | Dimming mode selection with internal 400k pull-up to VDC; floating or high gives 25% mixed mode dimming, low gives direct PWM mode dimming. |
| 5 | AGND | power_in | Analog ground of the LED driver. |
| 6 | LED6 | passive | Current sink for LED string 6; leave unconnected or short to GND if not used. |
| 7 | LED5 | passive | Current sink for LED string 5; leave unconnected or short to GND if not used. |
| 8 | LED4 | passive | Current sink for LED string 4; leave unconnected or short to GND if not used. |
| 9 | LED3 | passive | Current sink for LED string 3; leave unconnected or short to GND if not used. |
| 10 | LED2 | passive | Current sink for LED string 2; leave unconnected or short to GND if not used. |
| 11 | LED1 | passive | Current sink for LED string 1; leave unconnected or short to GND if not used. |
| 12 | OVP | input | Over voltage protection sense input with a detecting threshold of 1.2V (typ.). |
| 13 | PGND | power_in | Power ground of the boost converter (pins 13 and 14). |
| 14 | PGND | power_in | Power ground of the boost converter (pins 13 and 14). |
| 15 | LX | passive | Switching pin of the boost converter (pins 15 and 16); internal 200mΩ, 43V power switch with 2.5A typ. current limit. |
| 16 | LX | passive | Switching pin of the boost converter (pins 15 and 16); internal 200mΩ, 43V power switch with 2.5A typ. current limit. |
| 17 | PWM | input | PWM dimming control input; high is 1.3V to 24V, low up to 0.5V, dimming frequency 100Hz to 20kHz. |
| 18 | VDC | power_out | Internal regulator voltage (3.6V to 4V, 3.8V typ.); connect a capacitor from this pin to ground. |
| 19 | VIN | power_in | Power supply input, 2.5V to 24V operating range. |
| 20 | COMP | passive | Compensation node of the boost converter; connect a compensation network for stability. |
| 21 | GND | power_in | Exposed pad ground; must be soldered to a large PCB and connected to GND for maximum power dissipation. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Richtek Tech |
| Package | WQFN-20-EP(3x3) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 21 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Input Voltage | VIN | 2.5 | | 24 | V | | 4 |
| Junction Temperature Range | TJ | -40 | | 125 | °C | | 4 |
| Ambient Temperature Range | TA | -40 | | 85 | °C | | 4 |
| Supply Input Voltage to GND | VIN | -0.3 | | 26.5 | V | | 4 |
| EN, PWM, ISET, COMP, MIX, FREQ to GND | | -0.3 | | 26.5 | V | | 4 |
| LX, OVP, LED1 to LED6 to GND | | -0.3 | | 48 | V | | 4 |
| LX to GND | | -0.3 | | 48 | V | | 4 |
| LX to GND transient | | -1 | | 48 | V | < 500ns | 4 |
| VDC to GND | | -0.3 | | 7 | V | | 4 |
| Power Dissipation | PD | | | 1.471 | W | WQFN-20L 3x3, TA = 25°C | 4 |
| Junction Temperature | TJ | | | 150 | °C | | 4 |
| Storage Temperature Range | | -65 | | 150 | °C | | 4 |
| Lead Temperature | | | | 260 | °C | Soldering, 10 sec. | 4 |
| ESD HBM | | | | 2 | kV | | 4 |
| ESD MM | | | | 200 | V | | 4 |
| Thermal Resistance Junction-to-Ambient | θJA | | 68 | | °C/W | WQFN-20L 3x3 | 4 |
| Thermal Resistance Junction-to-Case | θJC | | 7.5 | | °C/W | WQFN-20L 3x3 | 4 |
| VIN Shutdown Current | ISHDN | | | 10 | A | VIN = 4.5V, EN = 0V | 4 |
| PWM Dimming Frequency | fPWM | 0.1 | | 20 | kHz | | 4 |
| EN, PWM Input High Voltage | VIH | 1.3 | | 24 | V | VIN = 2.5V to 24V | 4 |
| EN, PWM Input Low Voltage | VIL | | | 0.5 | V | VIN = 2.5V to 24V | 4 |
| Switching Frequency | fSW | 0.8 | 1 | 1.2 | MHz | RFSW = 22k | 4 |
| Switching Frequency | fSW | 0.4 | 0.5 | 0.6 | MHz | RFSW = 51k | 4 |
| LX On Resistance (N-MOSFET) | RLX | 0.18 | 0.2 | 0.22 | Ω | VIN > 4.5V | 4 |
| Minimum On-Time | tON(MIN) | 40 | 60 | 80 | ns | FSW = 1MHz | 5 |
| Maximum Duty | DMAX | 90 | 93 | 96 | % | FSW = 1MHz | 5 |
| LX Current Limit | ILIM | 2.2 | 2.5 | 2.8 | A | | 5 |
| Regulated VLEDx | VLEDx | 0.5 | 0.6 | 0.7 | V | Highest LED string, ILED = 20mA | 5 |
| LDO Output Voltage Range | VDC | 3.6 | 3.8 | 4 | V | | 5 |
| Maximum LED Current | IFB(MAX) | 5 | | 50 | mA | MODE = PWM Mode | 5 |
| Maximum LED Current | IFB(MAX) | 8 | | 50 | mA | MODE = Mixed Mode | 5 |
| LED Current Accuracy | ILEDA | 19.4 | 20 | 20.6 | mA | 2V > VLEDx > 0.5V, RISET = 12k | 5 |
| LED Current Matching | ILEDM | | | 2 | % | 2V > VLEDx > 0.5V, RISET = 12k | 5 |
| ISET Pin Voltage | VISET | 0.76 | 1 | 1.24 | V | | 5 |
| OVP Threshold | VOVP | 1.16 | 1.2 | 1.24 | V | | 5 |
| VIN Quiescent Current | IVIN | | 3 | | mA | PWM = COMP = 0V, not switching | 4 |
| VIN Quiescent Current (switching) | IVIN_SW | | 4 | | mA | PWM = COMP = 2V, switching | 4 |
| VIN UVLO Threshold rising | VUVLO | | 2.3 | | V | VIN rising | 4 |
| VIN UVLO Threshold falling | VUVLO | | 2.1 | | V | VIN falling | 4 |
| OVP UVLO Threshold | VOVPF | | 50 | | mV | | 5 |
| Thermal Shutdown Temperature | TSD | | 150 | | C | | 5 |
| OTP Hysteresis | TOTP_Hys | | 30 | | C | | 5 |
| LED Pin Under Voltage Threshold | VLSD | | 0.1 | | V | Un-Connection | 5 |
## CAD (KiCad official)
- Symbol: `RT8532GQW`
- Footprint: `Package_DFN_QFN:UQFN-20-1EP_3x3mm_P0.4mm_EP1.85x1.85mm`
- 3D model: WQFN-20-EP(3x3) (KiCad packages3D, STEP)
- 3D model files: `rt8532gqw-etched.step` / `rt8532gqw-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `rt8532gqw.step` / `rt8532gqw.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Richtek Tech datasheet](docs/rt8532gqw-datasheet.pdf) (14 pp, sha256 `a756183a9ce08327`, retrieved 2026-10-23, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/rt8532gqw-datasheet.pdf)