← Commit history

Initial commit: component/rf430cl331hirgtr

Ray ·7aebf21dbe ·
2 files changed +267
README.mdadded+54
@@ -0,0 +1,54 @@+# RF430CL331HIRGTR++**Texas Instruments** · RFID ICs · QFN-16-EP(3x3)++RF430CL331HIRGTR from Texas Instruments, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | ANT1 | input | RF antenna input 1 for AC-coupled connection to resonant LC antenna circuit. |+| 2 | ANT2 | input | RF antenna input 2 for AC-coupled connection to resonant LC antenna circuit. |+| 3 | RST | input | Reset input active-low with integrated 20-35 kΩ pullup resistor; held low for minimum one clock cycle to initiate device reset. |+| 4 | E0 | input | I2C address select pin 0; sets bit 0 of the programmable 7-bit slave address. |+| 5 | E1 | input | I2C address select pin 1; sets bit 1 of the programmable 7-bit slave address. |+| 6 | E2 | input | I2C address select pin 2; sets bit 2 of the programmable 7-bit slave address. |+| 7 | INTO | output | Interrupt output pin signaling enabled interrupt events; configurable active-high or active-low via General Control register. |+| 8 | I2C_READY | output | Status output; high level indicates I2C communication can be started, low level prohibits new I2C communication. |+| 9 | I2C_SIGNAL | output | Status output; low indicates wait-time-extension command is automatically being sent, I2C communication may continue. |+| 10 | SCL | bidirectional | I2C clock line with open-drain output; external pullup resistor required, supports clock stretching up to 400 kHz when master supports it. |+| 11 | SDA | bidirectional | I2C data line with open-drain output; external pullup resistor required, maximum write frequency 120 kHz and read frequency 100 kHz when device is addressed. |+| 12 | VCORE | power_out | Regulated 1.8 V core supply output for internal die circuitry; requires 0.1-0.47 µF decoupling capacitor. |+| 13 | VSS | power_in | Ground supply at 0 V reference potential. |+| 14 | NC | unconnected | No-connect pin, leave unconnected on printed circuit board. |+| 15 | VCC | power_in | 3.3 V primary supply input; operating range 3.0-3.6 V without RF field, 2.0-3.6 V with RF field present. |+| 16 | NC | unconnected | No-connect pin, leave unconnected on printed circuit board. |+| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | QFN-16-EP(3x3) |+| Category | RF And Wireless |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `RF430CL331HIRGTR`+- Footprint: `Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm`+- 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)+- 3D model files: `rf430cl331hirgtr-etched.step` / `rf430cl331hirgtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `rf430cl331hirgtr.step` / `rf430cl331hirgtr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/rf430cl331h) (63 pp, sha256 `78d8ec602eefb231`, retrieved 2026-09-27, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/rf430cl331hirgtr-datasheet.pdf)
page.jsonadded+213
@@ -0,0 +1,213 @@+{+  "slug": "rf430cl331hirgtr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments RFID ICs, QFN-16-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "rf and wireless",+    "rf430cl331hirgtr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "rf430cl331hirgtr.kicad_sym",+    "rf430cl331hirgtr.kicad_mod",+    "rf430cl331hirgtr.glb",+    "rf430cl331hirgtr.step",+    "rf430cl331hirgtr.lbr",+    "docs/hero.png",+    "docs/rf430cl331hirgtr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "RF430CL331HIRGTR",+    "manufacturer": "Texas Instruments",+    "package": "QFN-16-EP(3x3)",+    "pin_count": 17,+    "category": "RF And Wireless",+    "subcategory": "RFID ICs",+    "datasheet": "https://www.ti.com/cn/lit/gpn/rf430cl331h",+    "parts": {+      "symbol": "rf430cl331hirgtr.kicad_sym",+      "footprint": "rf430cl331hirgtr.kicad_mod",+      "model_3d": "rf430cl331hirgtr-etched.glb",+      "model_3d_plain": "rf430cl331hirgtr.glb",+      "model_3d_step": "rf430cl331hirgtr-etched.step",+      "model_3d_step_plain": "rf430cl331hirgtr.step",+      "lbr": "rf430cl331hirgtr.lbr"+    },+    "distributor_links": {+      "lcsc": "C2654825",+      "digikey": "296-44160-2-ND",+      "mouser": "595-RF430CL331HIRGTR"+    },+    "distributor_check": {+      "checked_at": "2026-09-27T05:40:25Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "296-44160-2-ND",+        "status": "found",+        "lifecycle": "Active"+      },+      "mouser": {+        "pn": "595-RF430CL331HIRGTR",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "ANT1",+        "type": "input",+        "description": "RF antenna input 1 for AC-coupled connection to resonant LC antenna circuit."+      },+      {+        "number": "2",+        "name": "ANT2",+        "type": "input",+        "description": "RF antenna input 2 for AC-coupled connection to resonant LC antenna circuit."+      },+      {+        "number": "3",+        "name": "RST",+        "type": "input",+        "description": "Reset input active-low with integrated 20-35 kΩ pullup resistor; held low for minimum one clock cycle to initiate device reset."+      },+      {+        "number": "4",+        "name": "E0",+        "type": "input",+        "description": "I2C address select pin 0; sets bit 0 of the programmable 7-bit slave address."+      },+      {+        "number": "5",+        "name": "E1",+        "type": "input",+        "description": "I2C address select pin 1; sets bit 1 of the programmable 7-bit slave address."+      },+      {+        "number": "6",+        "name": "E2",+        "type": "input",+        "description": "I2C address select pin 2; sets bit 2 of the programmable 7-bit slave address."+      },+      {+        "number": "7",+        "name": "INTO",+        "type": "output",+        "description": "Interrupt output pin signaling enabled interrupt events; configurable active-high or active-low via General Control register."+      },+      {+        "number": "8",+        "name": "I2C_READY",+        "type": "output",+        "description": "Status output; high level indicates I2C communication can be started, low level prohibits new I2C communication."+      },+      {+        "number": "9",+        "name": "I2C_SIGNAL",+        "type": "output",+        "description": "Status output; low indicates wait-time-extension command is automatically being sent, I2C communication may continue."+      },+      {+        "number": "10",+        "name": "SCL",+        "type": "bidirectional",+        "description": "I2C clock line with open-drain output; external pullup resistor required, supports clock stretching up to 400 kHz when master supports it."+      },+      {+        "number": "11",+        "name": "SDA",+        "type": "bidirectional",+        "description": "I2C data line with open-drain output; external pullup resistor required, maximum write frequency 120 kHz and read frequency 100 kHz when device is addressed."+      },+      {+        "number": "12",+        "name": "VCORE",+        "type": "power_out",+        "description": "Regulated 1.8 V core supply output for internal die circuitry; requires 0.1-0.47 µF decoupling capacitor."+      },+      {+        "number": "13",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground supply at 0 V reference potential."+      },+      {+        "number": "14",+        "name": "NC",+        "type": "unconnected",+        "description": "No-connect pin, leave unconnected on printed circuit board."+      },+      {+        "number": "15",+        "name": "VCC",+        "type": "power_in",+        "description": "3.3 V primary supply input; operating range 3.0-3.6 V without RF field, 2.0-3.6 V with RF field present."+      },+      {+        "number": "16",+        "name": "NC",+        "type": "unconnected",+        "description": "No-connect pin, leave unconnected on printed circuit board."+      },+      {+        "number": "17",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: ANT1 and ANT2 are RF/analog antenna inputs; physical design requires LC resonant circuit with coil i; Exposed thermal pad is present in QFN-16-EP package but not listed in electrical pin table; pad must; Pin 15 (VCC) exhibits non-standard behavior where minimum supply voltage 2.0 V is permitted only whe",+          "exposed pad 17 added from the footprint"+        ],+        "pages_sent": 63,+        "cost_usd": 0.5114,+        "at": "2026-09-27T05:40:08"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/rf430cl331h",+        "pages": 63,+        "sha256": "78d8ec602eefb231",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 17,+        "described": 17,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file