main
Ray
Publish 0.1.0
1fe4696
RF2052TR13
Qorvo · RF Mixers · QFN-32-EP(5x5)
RF2052TR13 from Qorvo, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ENBL | input | Enable input; the ENBL high voltage level must not be greater than VDD, and an RC low-pass filter could be used to reduce digital noise. |
| 2 | INDP | passive | VCO 3 differential inductor pin; normally a micro-strip inductor sets the VCO 3 frequency range of 1200MHz to 1600MHz. |
| 3 | INDN | passive | VCO 3 differential inductor pin; normally a micro-strip inductor sets the VCO 3 frequency range of 1200MHz to 1600MHz. |
| 4 | REXT | passive | External bandgap bias resistor pin; connect a 51k resistor to ground to set the bandgap reference bias current, and it can be a sensitive low frequency noise injection point. |
| 5 | ANA_DEC | passive | Analog supply decoupling capacitor pin; connect to analog supply and decouple as close to the pin as possible. |
| 6 | LFILT1 | passive | Phase detector output, a low-frequency noise-sensitive node. |
| 7 | LFILT2 | passive | Loop filter op-amp output, a low-frequency noise-sensitive node. |
| 8 | LFILT3 | passive | VCO control input, a low-frequency noise-sensitive node. |
| 9 | MODE | input | Mode select pin; an RC low-pass filter can be used to reduce digital noise. |
| 10 | XTALIPP | input | Reference crystal / reference oscillator input; should be AC-coupled if an external reference is used (or decoupled to ground per note 3). |
| 11 | XTALIPN | input | Reference crystal / reference oscillator input; should be AC-coupled to ground if an external reference is used (an external reference may alternatively be AC-coupled here per note 3). |
| 12 | GND | power_in | Connect to ground. |
| 13 | NC | unconnected | No connect. |
| 14 | NC | unconnected | No connect. |
| 15 | NC | unconnected | No connect. |
| 16 | NC | unconnected | No connect. |
| 17 | NC | unconnected | No connect. |
| 18 | NC | unconnected | No connect. |
| 19 | DIG_VDD | power_in | Digital supply (2.7V to 3.6V operation); should be decoupled as close to the pin as possible. |
| 20 | NC | unconnected | No connect. |
| 21 | NC | unconnected | No connect. |
| 22 | ANA_VDD | power_in | Analog supply (2.7V to 3.6V operation); should be decoupled as close to the pin as possible. |
| 23 | RFIPN | input | Differential RF mixer input; connect so DC current cannot flow into or out of the chip, using AC coupling capacitors or a transformer. |
| 24 | RFIPP | input | Differential RF mixer input; connect so DC current cannot flow into or out of the chip, using AC coupling capacitors or a transformer. |
| 25 | NC | unconnected | No connect. |
| 26 | NC | unconnected | No connect. |
| 27 | RFOPN | output | Differential RF mixer output; DC current must flow from ANA_VDD into this pin through an RF inductor or transformer. |
| 28 | RFOPP | output | Differential RF mixer output; DC current must flow from ANA_VDD into this pin through an RF inductor or transformer. |
| 29 | RESETB | input | Chip reset, active low; connect to DIG_VDD if external reset is not required. |
| 30 | ENX | input | Serial interface select, active low; an RC low-pass filter could be used to reduce digital noise. |
| 31 | SCLK | input | Serial interface clock; an RC low-pass filter could be used to reduce digital noise. |
| 32 | SDATA | bidirectional | Serial interface data; an RC low-pass filter could be used to reduce digital noise. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Qorvo |
| Package | QFN-32-EP(5x5) |
| Category | RF & Radio |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (absolute maximum) | VDD | -0.5 | 3.6 | V | 4 | ||
| RF/IF Mixer Input Power | 15 | dBm | 4 | ||||
| Operating Temperature Range (absolute maximum) | -40 | 85 | °C | 4 | |||
| Storage Temperature Range | -65 | 150 | °C | 4 | |||
| Supply Voltage | VDD | 2.7 | 3 | 3.6 | V | 4 | |
| Temperature | TOP | -40 | 85 | °C | 4 | ||
| Input Low Voltage | -0.3 | 0.5 | V | Logic inputs/outputs, VDD=Supply to DIG_VDD pin | 4 | ||
| Input Low Current | -10 | 10 | uA | Input=0V | 4 | ||
| Input High Current | -10 | 10 | uA | Input=VDD | 4 | ||
| Load Resistance | 10 | k | Logic inputs/outputs | 4 | |||
| Load Capacitance | 20 | pF | Logic inputs/outputs | 4 | |||
| RF and IF Port Frequency Range | 30 | 2500 | MHz | 5 | |||
| Xtal Frequency | 10 | 52 | MHz | Reference Oscillator | 5 | ||
| External Reference Frequency | 10 | 104 | MHz | Reference Oscillator | 5 | ||
| Reference Divider Ratio | 1 | 7 | 5 | ||||
| External Reference Input Level | 500 | 800 | 1500 | mVP-P | AC-coupled | 5 | |
| Synthesizer Output Frequency | 300 | 2400 | MHz | Dependant on VCO 3 external inductor. After LO dividers. | 5 | ||
| Phase Detector Frequency | 52 | MHz | 5 | ||||
| Reset delay | t1 | 5 | ns | Serial data timing, printed >5ns | 14 | ||
| Programming setup time | t2 | 5 | ns | Printed >5ns | 14 | ||
| Programming hold time | t3 | 5 | ns | Printed >5ns | 14 | ||
| ENX setup time | t4 | 5 | ns | Printed >5ns | 14 | ||
| ENX hold time | t5 | 5 | ns | Printed >5ns | 14 | ||
| Data setup time | t6 | 5 | ns | Printed >5ns | 14 | ||
| Data hold time | t7 | 5 | ns | Printed >5ns | 14 | ||
| ENBL setup time | t8 | 0 | ns | Printed >0ns | 14 | ||
| ENBL hold time | t9 | 0 | ns | Printed >0ns | 14 | ||
| Programmable Supply Current, Low Current Setting | IDD | 55 | mA | Static | 4 | ||
| Programmable Supply Current, High Linearity Setting | IDD | 75 | mA | Static | 4 | ||
| Standby Current | 3 | mA | Reference oscillator and bandgap only. | 4 | |||
| Power Down Current | 140 | A | ENBL=0 and REF_STBY=0 | 4 | |||
| Mixer Gain | -2 | dB | Mixer output driving 4:1 balun. Not including balun losses. | 4 | |||
| Mixer Noise Figure, Low Current Setting | 9.5 | dB | Mixer output driving 4:1 balun. | 4 | |||
| Mixer Noise Figure, High Linearity Setting | 12 | dB | Mixer output driving 4:1 balun. | 4 | |||
| IIP3, Low Current Setting | IIP3 | 10 | dBm | 5 | |||
| IIP3, High Linearity Setting | IIP3 | 18 | dBm | 5 | |||
| Pin1dB, Low Current Setting | Pin1dB | 2 | dBm | 5 | |||
| Pin1dB, High Linearity Setting | Pin1dB | 12 | dBm | 5 |
CAD (KiCad official)
- Symbol:
RF2052TR13 - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
rf2052tr13-etched.step/rf2052tr13-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);rf2052tr13.step/rf2052tr13.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Qorvo datasheet (37 pp, sha256
3391d87dd0ce38ae, retrieved 2026-10-31, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# RF2052TR13
**Qorvo** · RF Mixers · QFN-32-EP(5x5)
RF2052TR13 from Qorvo, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ENBL | input | Enable input; the ENBL high voltage level must not be greater than VDD, and an RC low-pass filter could be used to reduce digital noise. |
| 2 | INDP | passive | VCO 3 differential inductor pin; normally a micro-strip inductor sets the VCO 3 frequency range of 1200MHz to 1600MHz. |
| 3 | INDN | passive | VCO 3 differential inductor pin; normally a micro-strip inductor sets the VCO 3 frequency range of 1200MHz to 1600MHz. |
| 4 | REXT | passive | External bandgap bias resistor pin; connect a 51k resistor to ground to set the bandgap reference bias current, and it can be a sensitive low frequency noise injection point. |
| 5 | ANA_DEC | passive | Analog supply decoupling capacitor pin; connect to analog supply and decouple as close to the pin as possible. |
| 6 | LFILT1 | passive | Phase detector output, a low-frequency noise-sensitive node. |
| 7 | LFILT2 | passive | Loop filter op-amp output, a low-frequency noise-sensitive node. |
| 8 | LFILT3 | passive | VCO control input, a low-frequency noise-sensitive node. |
| 9 | MODE | input | Mode select pin; an RC low-pass filter can be used to reduce digital noise. |
| 10 | XTALIPP | input | Reference crystal / reference oscillator input; should be AC-coupled if an external reference is used (or decoupled to ground per note 3). |
| 11 | XTALIPN | input | Reference crystal / reference oscillator input; should be AC-coupled to ground if an external reference is used (an external reference may alternatively be AC-coupled here per note 3). |
| 12 | GND | power_in | Connect to ground. |
| 13 | NC | unconnected | No connect. |
| 14 | NC | unconnected | No connect. |
| 15 | NC | unconnected | No connect. |
| 16 | NC | unconnected | No connect. |
| 17 | NC | unconnected | No connect. |
| 18 | NC | unconnected | No connect. |
| 19 | DIG_VDD | power_in | Digital supply (2.7V to 3.6V operation); should be decoupled as close to the pin as possible. |
| 20 | NC | unconnected | No connect. |
| 21 | NC | unconnected | No connect. |
| 22 | ANA_VDD | power_in | Analog supply (2.7V to 3.6V operation); should be decoupled as close to the pin as possible. |
| 23 | RFIPN | input | Differential RF mixer input; connect so DC current cannot flow into or out of the chip, using AC coupling capacitors or a transformer. |
| 24 | RFIPP | input | Differential RF mixer input; connect so DC current cannot flow into or out of the chip, using AC coupling capacitors or a transformer. |
| 25 | NC | unconnected | No connect. |
| 26 | NC | unconnected | No connect. |
| 27 | RFOPN | output | Differential RF mixer output; DC current must flow from ANA_VDD into this pin through an RF inductor or transformer. |
| 28 | RFOPP | output | Differential RF mixer output; DC current must flow from ANA_VDD into this pin through an RF inductor or transformer. |
| 29 | RESETB | input | Chip reset, active low; connect to DIG_VDD if external reset is not required. |
| 30 | ENX | input | Serial interface select, active low; an RC low-pass filter could be used to reduce digital noise. |
| 31 | SCLK | input | Serial interface clock; an RC low-pass filter could be used to reduce digital noise. |
| 32 | SDATA | bidirectional | Serial interface data; an RC low-pass filter could be used to reduce digital noise. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Qorvo |
| Package | QFN-32-EP(5x5) |
| Category | RF & Radio |
| Pins | 33 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (absolute maximum) | VDD | -0.5 | | 3.6 | V | | 4 |
| RF/IF Mixer Input Power | | | | 15 | dBm | | 4 |
| Operating Temperature Range (absolute maximum) | | -40 | | 85 | °C | | 4 |
| Storage Temperature Range | | -65 | | 150 | °C | | 4 |
| Supply Voltage | VDD | 2.7 | 3 | 3.6 | V | | 4 |
| Temperature | TOP | -40 | | 85 | °C | | 4 |
| Input Low Voltage | | -0.3 | | 0.5 | V | Logic inputs/outputs, VDD=Supply to DIG_VDD pin | 4 |
| Input Low Current | | -10 | | 10 | uA | Input=0V | 4 |
| Input High Current | | -10 | | 10 | uA | Input=VDD | 4 |
| Load Resistance | | 10 | | | k | Logic inputs/outputs | 4 |
| Load Capacitance | | | | 20 | pF | Logic inputs/outputs | 4 |
| RF and IF Port Frequency Range | | 30 | | 2500 | MHz | | 5 |
| Xtal Frequency | | 10 | | 52 | MHz | Reference Oscillator | 5 |
| External Reference Frequency | | 10 | | 104 | MHz | Reference Oscillator | 5 |
| Reference Divider Ratio | | 1 | | 7 | | | 5 |
| External Reference Input Level | | 500 | 800 | 1500 | mVP-P | AC-coupled | 5 |
| Synthesizer Output Frequency | | 300 | | 2400 | MHz | Dependant on VCO 3 external inductor. After LO dividers. | 5 |
| Phase Detector Frequency | | | | 52 | MHz | | 5 |
| Reset delay | t1 | 5 | | | ns | Serial data timing, printed >5ns | 14 |
| Programming setup time | t2 | 5 | | | ns | Printed >5ns | 14 |
| Programming hold time | t3 | 5 | | | ns | Printed >5ns | 14 |
| ENX setup time | t4 | 5 | | | ns | Printed >5ns | 14 |
| ENX hold time | t5 | 5 | | | ns | Printed >5ns | 14 |
| Data setup time | t6 | 5 | | | ns | Printed >5ns | 14 |
| Data hold time | t7 | 5 | | | ns | Printed >5ns | 14 |
| ENBL setup time | t8 | 0 | | | ns | Printed >0ns | 14 |
| ENBL hold time | t9 | 0 | | | ns | Printed >0ns | 14 |
| Programmable Supply Current, Low Current Setting | IDD | | 55 | | mA | Static | 4 |
| Programmable Supply Current, High Linearity Setting | IDD | | 75 | | mA | Static | 4 |
| Standby Current | | | 3 | | mA | Reference oscillator and bandgap only. | 4 |
| Power Down Current | | | 140 | | A | ENBL=0 and REF_STBY=0 | 4 |
| Mixer Gain | | | -2 | | dB | Mixer output driving 4:1 balun. Not including balun losses. | 4 |
| Mixer Noise Figure, Low Current Setting | | | 9.5 | | dB | Mixer output driving 4:1 balun. | 4 |
| Mixer Noise Figure, High Linearity Setting | | | 12 | | dB | Mixer output driving 4:1 balun. | 4 |
| IIP3, Low Current Setting | IIP3 | | 10 | | dBm | | 5 |
| IIP3, High Linearity Setting | IIP3 | | 18 | | dBm | | 5 |
| Pin1dB, Low Current Setting | Pin1dB | | 2 | | dBm | | 5 |
| Pin1dB, High Linearity Setting | Pin1dB | | 12 | | dBm | | 5 |
## CAD (KiCad official)
- Symbol: `RF2052TR13`
- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`
- 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files: `rf2052tr13-etched.step` / `rf2052tr13-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `rf2052tr13.step` / `rf2052tr13.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Qorvo datasheet](docs/rf2052tr13-datasheet.pdf) (37 pp, sha256 `3391d87dd0ce38ae`, retrieved 2026-10-31, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/rf2052tr13-datasheet.pdf)