main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers rf2052tr13: viewers · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
rf2052tr13-etched.glb Publish 0.1.0 · Ray
rf2052tr13-etched.step rf2052tr13: factory component page (tier=lcsc) · Ray
rf2052tr13-hero.glb rf2052tr13: hero GLB from the etched model (keeps the MPN mark) · Ray
rf2052tr13-hero.overlay.json Publish 0.1.0 · Ray
rf2052tr13.glb Publish 0.1.0 · Ray
rf2052tr13.kicad_mod Publish 0.1.0 · Ray
rf2052tr13.kicad_sym Publish 0.1.0 · Ray
rf2052tr13.lbr Publish 0.1.0 · Ray
rf2052tr13.step Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier lcsc, 33 pins · Ray

RF2052TR13

Qorvo · RF Mixers · QFN-32-EP(5x5)

RF2052TR13 from Qorvo, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 ENBL input Enable input; the ENBL high voltage level must not be greater than VDD, and an RC low-pass filter could be used to reduce digital noise.
2 INDP passive VCO 3 differential inductor pin; normally a micro-strip inductor sets the VCO 3 frequency range of 1200MHz to 1600MHz.
3 INDN passive VCO 3 differential inductor pin; normally a micro-strip inductor sets the VCO 3 frequency range of 1200MHz to 1600MHz.
4 REXT passive External bandgap bias resistor pin; connect a 51k resistor to ground to set the bandgap reference bias current, and it can be a sensitive low frequency noise injection point.
5 ANA_DEC passive Analog supply decoupling capacitor pin; connect to analog supply and decouple as close to the pin as possible.
6 LFILT1 passive Phase detector output, a low-frequency noise-sensitive node.
7 LFILT2 passive Loop filter op-amp output, a low-frequency noise-sensitive node.
8 LFILT3 passive VCO control input, a low-frequency noise-sensitive node.
9 MODE input Mode select pin; an RC low-pass filter can be used to reduce digital noise.
10 XTALIPP input Reference crystal / reference oscillator input; should be AC-coupled if an external reference is used (or decoupled to ground per note 3).
11 XTALIPN input Reference crystal / reference oscillator input; should be AC-coupled to ground if an external reference is used (an external reference may alternatively be AC-coupled here per note 3).
12 GND power_in Connect to ground.
13 NC unconnected No connect.
14 NC unconnected No connect.
15 NC unconnected No connect.
16 NC unconnected No connect.
17 NC unconnected No connect.
18 NC unconnected No connect.
19 DIG_VDD power_in Digital supply (2.7V to 3.6V operation); should be decoupled as close to the pin as possible.
20 NC unconnected No connect.
21 NC unconnected No connect.
22 ANA_VDD power_in Analog supply (2.7V to 3.6V operation); should be decoupled as close to the pin as possible.
23 RFIPN input Differential RF mixer input; connect so DC current cannot flow into or out of the chip, using AC coupling capacitors or a transformer.
24 RFIPP input Differential RF mixer input; connect so DC current cannot flow into or out of the chip, using AC coupling capacitors or a transformer.
25 NC unconnected No connect.
26 NC unconnected No connect.
27 RFOPN output Differential RF mixer output; DC current must flow from ANA_VDD into this pin through an RF inductor or transformer.
28 RFOPP output Differential RF mixer output; DC current must flow from ANA_VDD into this pin through an RF inductor or transformer.
29 RESETB input Chip reset, active low; connect to DIG_VDD if external reset is not required.
30 ENX input Serial interface select, active low; an RC low-pass filter could be used to reduce digital noise.
31 SCLK input Serial interface clock; an RC low-pass filter could be used to reduce digital noise.
32 SDATA bidirectional Serial interface data; an RC low-pass filter could be used to reduce digital noise.
33 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Qorvo
Package QFN-32-EP(5x5)
Category RF & Radio
Pins 33

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage (absolute maximum) VDD -0.5 3.6 V 4
RF/IF Mixer Input Power 15 dBm 4
Operating Temperature Range (absolute maximum) -40 85 °C 4
Storage Temperature Range -65 150 °C 4
Supply Voltage VDD 2.7 3 3.6 V 4
Temperature TOP -40 85 °C 4
Input Low Voltage -0.3 0.5 V Logic inputs/outputs, VDD=Supply to DIG_VDD pin 4
Input Low Current -10 10 uA Input=0V 4
Input High Current -10 10 uA Input=VDD 4
Load Resistance 10 k Logic inputs/outputs 4
Load Capacitance 20 pF Logic inputs/outputs 4
RF and IF Port Frequency Range 30 2500 MHz 5
Xtal Frequency 10 52 MHz Reference Oscillator 5
External Reference Frequency 10 104 MHz Reference Oscillator 5
Reference Divider Ratio 1 7 5
External Reference Input Level 500 800 1500 mVP-P AC-coupled 5
Synthesizer Output Frequency 300 2400 MHz Dependant on VCO 3 external inductor. After LO dividers. 5
Phase Detector Frequency 52 MHz 5
Reset delay t1 5 ns Serial data timing, printed >5ns 14
Programming setup time t2 5 ns Printed >5ns 14
Programming hold time t3 5 ns Printed >5ns 14
ENX setup time t4 5 ns Printed >5ns 14
ENX hold time t5 5 ns Printed >5ns 14
Data setup time t6 5 ns Printed >5ns 14
Data hold time t7 5 ns Printed >5ns 14
ENBL setup time t8 0 ns Printed >0ns 14
ENBL hold time t9 0 ns Printed >0ns 14
Programmable Supply Current, Low Current Setting IDD 55 mA Static 4
Programmable Supply Current, High Linearity Setting IDD 75 mA Static 4
Standby Current 3 mA Reference oscillator and bandgap only. 4
Power Down Current 140 A ENBL=0 and REF_STBY=0 4
Mixer Gain -2 dB Mixer output driving 4:1 balun. Not including balun losses. 4
Mixer Noise Figure, Low Current Setting 9.5 dB Mixer output driving 4:1 balun. 4
Mixer Noise Figure, High Linearity Setting 12 dB Mixer output driving 4:1 balun. 4
IIP3, Low Current Setting IIP3 10 dBm 5
IIP3, High Linearity Setting IIP3 18 dBm 5
Pin1dB, Low Current Setting Pin1dB 2 dBm 5
Pin1dB, High Linearity Setting Pin1dB 12 dBm 5

CAD (KiCad official)

  • Symbol: RF2052TR13
  • Footprint: Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm
  • 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: rf2052tr13-etched.step / rf2052tr13-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); rf2052tr13.step / rf2052tr13.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Qorvo datasheet (37 pp, sha256 3391d87dd0ce38ae, retrieved 2026-10-31, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF