Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

REG113NA-5

Texas Instruments · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SOT-23-5

REG113NA-5 from Texas Instruments, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Supply input; specified input range is VOUT + 0.4 V to 10 V (VIN > 1.8 V), with an absolute maximum of 12 V and the regulator dropping out when VIN < VOUT + VDROP(MAX).
2 GND power_in Ground reference pin; ground pin current is typically 850 µA at IOUT = 400 mA and 400 µA at IOUT = 5 mA, and drops to about 10 nA when the regulator is disabled.
3 Enable input Active-high enable compatible with TTL-CMOS levels: inputs at or above 1.8 V turn the output on and inputs at or below 0.5 V (max) turn it off, with an absolute maximum of -0.3 V to VIN; it can be tied to VIN when unused.
4 NR passive Noise reduction pin for an optional capacitor CNR (typically 0.01 µF) to ground that filters the internal reference and lowers output noise; absolute maximum voltage is -0.3 V to 6.0 V.
5 VOUT power_out Regulated output rated for up to 400 mA load current with a typical 500 mA current limit and foldback to 200 mA short-circuit current; no output capacitor is required for stability.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOT-23-5
Category Power Management (PMIC)
Pins 5

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Accuracy (output voltage, at TJ=+25°C) -1.5 0.5 1.5 % 3
Accuracy over temperature -2.3 2.3 % 3
Output voltage vs temperature dVOUT/dT -2.3 50 2.3 ppm/°C 3
Output voltage vs line and load -2.3 1 2.3 % IOUT = 5mA to 400mA, VIN = (VOUT + 0.4V) to 10V 3
Output voltage vs line and load, over temperature -3 3 % IOUT = 5mA to 400mA, VIN = (VOUT + 0.6V) to 10V 3
DC dropout voltage VDROP 4 10 mV IOUT = 5mA 3
DC dropout voltage VDROP 250 325 mV IOUT = 400mA 3
DC dropout voltage, over temperature VDROP 410 mV IOUT = 400mA 3
Current limit ICL 425 500 575 mA 3
Current limit, over temperature ICL 600 mA 3
Enable input voltage HIGH (output enabled) VENABLE 1.8 V 3
Enable input voltage LOW (output disabled) VENABLE -0.2 0.5 V 3
Enable input current HIGH (output enabled) IENABLE 1 100 nA VENABLE = 1.8V to VIN, VIN = 1.8V to 6.5(4) 3
Enable input current LOW (output disabled) IENABLE 2 100 nA VENABLE = 0V to 0.5V 3
Ground pin current IGND 400 500 µA IOUT = 5mA 3
Ground pin current IGND 850 1000 µA IOUT = 400mA 3
Enable pin current, not enabled 0.01 0.2 µA VENABLE ≤ 0.5V 3
Operating input voltage range VIN 1.8 10 V 3
Specified input voltage range VIN 10 V VIN > 1.8V 3
Specified input voltage range, over temperature VIN 10 V VIN > 1.8V 3
Specified temperature range TJ -40 85 °C 3
Operating temperature range TJ -55 125 °C 3
Storage temperature range TA -65 150 °C 3
Supply input voltage VIN -0.3 12 V 2
Enable input voltage VEN -0.3 V 2
NR pin voltage VNR -0.3 6 V 2
Operating temperature range TJ -55 125 °C 2
Storage temperature range TA -65 150 °C 2
Lead temperature (soldering, 3s) 240 °C soldering, 3s 2
Thermal resistance, junction-to-ambient (SOT23-5) θJA 200 °C/W Junction-to-Ambient 3
Output voltage (REG113-5) VOUT 5 V 3
Short-circuit current limit ISC 200 mA 3
Ripple rejection 65 dB f = 120Hz 3
Thermal shutdown junction temperature 160 °C Shutdown 3
Thermal shutdown reset junction temperature 140 °C Reset from shutdown 3
Output disable time 50 µs COUT = 1.0µF, RLOAD = 13Ω 3
Output enable softstart time 1.5 ms COUT = 1.0µF, RLOAD = 13Ω 3
Output voltage noise without CNR Vn 23 µVrms/V • VOUT CNR = 0, COUT = 0 3
Output voltage noise with CNR Vn 7 µVrms/V • VOUT CNR = 0.01µF, COUT = 10µF 3

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper connected to fused leads 5 to 8. See Figure 7 for thermal resistance for varying areas of copper. Using heavier copper 10

CAD (KiCad official)

  • Symbol: REG113NA-5
  • Footprint: Package_TO_SOT_SMD:SOT-23-5
  • 3D model: SOT-23-5, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: reg113na-5-3k-etched.step / reg113na-5-3k-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); reg113na-5-3k.step / reg113na-5-3k.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (22 pp, sha256 c0da90b6895895f3, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF