component
PTH08T230WAD
Public Made by Adomby adom
Texas Instruments DC-DC Power Modules, DIP-10. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+46@@ -0,0 +1,46 @@+# PTH08T230WAD++**Texas Instruments** · DC-DC Power Modules · DIP-10++PTH08T230WAD from Texas Instruments, in a DIP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | SmartSync | input | Input that synchronizes the module switching frequency to an external clock; if unused it should be connected to GND (pin 3). |+| 2 | VI | power_in | Positive input voltage power node to the module, referenced to the common GND. |+| 3 | GND | power_in | Common ground for the VI and VO power connections and the 0 Vdc reference for the control inputs. |+| 4 | VO | power_out | Regulated positive power output with respect to GND. |+| 5 | +Sense | input | Sense input that lets the regulation compensate for voltage drop between the module and the load; for optimal accuracy it must be connected to VO close to the load. |+| 6 | -Sense | input | Sense input that lets the regulation compensate for voltage drop; for optimal accuracy it must be connected to GND (pin 3) very close to the module, within 10 cm. |+| 7 | VO Adjust | input | Output voltage adjust pin: a 0.05 W 1% resistor must be connected between this pin and -Sense (pin 6) to set the output above 0.69 V, over a set-point range of 0.69 V to 5.5 V; if left open the output defaults to its lowest value. |+| 8 | TurboTrans | input | Transient response adjust pin: a 1%, 0.05 W resistor between this pin and +Sense (pin 5) activates TurboTrans; leave open if unused, and external capacitance must never be connected to this pin unless the resistor is a 0 Ω short. |+| 9 | Track | input | Analog control input that makes the output follow an external voltage volt-for-volt from 0 V up to the set-point voltage, becoming active typically 20 ms after VI is applied; if unused it should be connected to VI. |+| 10 | Inhibit/UVLO | input | Open-collector/drain, negative-logic inhibit input referenced to GND: a low level disables the output (open-circuit leaves the module enabled), and a resistor from this pin to GND (pin 3) raises the input UVLO ON threshold. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | DIP-10 |+| Category | Power Modules |+| Pins | 10 |++## CAD (KiCad official)++- Symbol: `PTH08T230WAD`+- Footprint: `Package_DIP:DIP-10_W7.62mm`+- 3D model: DIP-10 (KiCad packages3D, STEP)+- 3D model files: `pth08t230wad-etched.step` / `pth08t230wad-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `pth08t230wad.step` / `pth08t230wad.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/pth08t230w) (39 pp, sha256 `feea6256e1032766`, retrieved 2026-10-08, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/pth08t230wad-datasheet.pdf)
page.jsonadded+212@@ -0,0 +1,212 @@+{+ "slug": "pth08t230wad",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Power Modules, DIP-10. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power modules",+ "pth08t230wad",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "pth08t230wad.kicad_sym",+ "pth08t230wad.kicad_mod",+ "pth08t230wad.glb",+ "pth08t230wad.step",+ "pth08t230wad.lbr",+ "docs/hero.png",+ "docs/pth08t230wad-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "pth08t230wad-hero.glb",+ "pth08t230wad-hero.overlay.json"+ ],+ "component": {+ "mpn": "PTH08T230WAD",+ "manufacturer": "Texas Instruments",+ "package": "DIP-10",+ "pin_count": 10,+ "category": "Power Modules",+ "subcategory": "DC-DC Power Modules",+ "datasheet": "https://www.ti.com/cn/lit/gpn/pth08t230w",+ "parts": {+ "symbol": "pth08t230wad.kicad_sym",+ "footprint": "pth08t230wad.kicad_mod",+ "model_3d": "pth08t230wad-hero.glb",+ "model_3d_plain": "pth08t230wad.glb",+ "model_3d_step": "pth08t230wad-etched.step",+ "model_3d_step_plain": "pth08t230wad.step",+ "lbr": "pth08t230wad.lbr"+ },+ "distributor_links": {+ "lcsc": "C485568",+ "digikey": "296-20647-ND",+ "mouser": "595-PTH08T230WAD"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T19:01:45Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-20647-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "595-PTH08T230WAD",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "SmartSync",+ "type": "input",+ "description": "Input that synchronizes the module switching frequency to an external clock; if unused it should be connected to GND (pin 3)."+ },+ {+ "number": "2",+ "name": "VI",+ "type": "power_in",+ "description": "Positive input voltage power node to the module, referenced to the common GND."+ },+ {+ "number": "3",+ "name": "GND",+ "type": "power_in",+ "description": "Common ground for the VI and VO power connections and the 0 Vdc reference for the control inputs."+ },+ {+ "number": "4",+ "name": "VO",+ "type": "power_out",+ "description": "Regulated positive power output with respect to GND."+ },+ {+ "number": "5",+ "name": "+Sense",+ "type": "input",+ "description": "Sense input that lets the regulation compensate for voltage drop between the module and the load; for optimal accuracy it must be connected to VO close to the load."+ },+ {+ "number": "6",+ "name": "-Sense",+ "type": "input",+ "description": "Sense input that lets the regulation compensate for voltage drop; for optimal accuracy it must be connected to GND (pin 3) very close to the module, within 10 cm."+ },+ {+ "number": "7",+ "name": "VO Adjust",+ "type": "input",+ "description": "Output voltage adjust pin: a 0.05 W 1% resistor must be connected between this pin and -Sense (pin 6) to set the output above 0.69 V, over a set-point range of 0.69 V to 5.5 V; if left open the output defaults to its lowest value."+ },+ {+ "number": "8",+ "name": "TurboTrans",+ "type": "input",+ "description": "Transient response adjust pin: a 1%, 0.05 W resistor between this pin and +Sense (pin 5) activates TurboTrans; leave open if unused, and external capacitance must never be connected to this pin unless the resistor is a 0 Ω short."+ },+ {+ "number": "9",+ "name": "Track",+ "type": "input",+ "description": "Analog control input that makes the output follow an external voltage volt-for-volt from 0 V up to the set-point voltage, becoming active typically 20 ms after VI is applied; if unused it should be connected to VI."+ },+ {+ "number": "10",+ "name": "Inhibit/UVLO",+ "type": "input",+ "description": "Open-collector/drain, negative-logic inhibit input referenced to GND: a low level disables the output (open-circuit leaves the module enabled), and a resistor from this pin to GND (pin 3) raises the input UVLO ON threshold."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The datasheet does not call this package DIP-10. The only package reference for PTH08T230WAD is the "+ ],+ "pages_sent": 14,+ "cost_usd": 0.0939,+ "at": "2026-10-08T19:01:28"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/pth08t230w",+ "pages": 39,+ "sha256": "feea6256e1032766",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 10,+ "described": 10,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "pth08t230wad.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "body on z = 0, through-hole leads below",+ "extents_mm": [+ 7.62,+ 12.7,+ 6.98+ ],+ "zmin_mm": -3.3,+ "centre_offset_mm": 0.127,+ "footprint_binding": "identity",+ "sha256": "d55cf1368e362bcb87f165c0a42ca34c9cdc0e591dae011d929545c8f6b7e91f",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "pth08t230wad-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "body on z = 0, through-hole leads below",+ "extents_mm": [+ 7.62,+ 12.7,+ 6.98+ ],+ "zmin_mm": -3.3,+ "centre_offset_mm": 0.127,+ "footprint_binding": "identity",+ "sha256": "5baa69831b79af55fe34b21a6e6cdee6d8f15bd423c59d7a7fa26cf3a41948c5",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}