Generated by kicad-footprint-generator · KiCad file format 20260206
PTH04T231WAD
Texas Instruments · Power Modules · DIP-10
PTH04T231WAD from Texas Instruments, in a DIP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SmartSync | input | This input pin synchronizes the module's switching frequency to an external clock, and if unused it should be connected to GND (pin 3). |
| 2 | VI | power_in | The positive input voltage power node to the module, referenced to common GND, with an input range of 2.2 V to 5.5 V. |
| 3 | GND | power_in | This is the common ground connection for the VI and VO power connections and the 0 Vdc reference for the control inputs. |
| 4 | VO | power_out | The regulated positive power output with respect to GND, adjustable from 0.69 V to 3.6 V. |
| 5 | +Sense | input | The sense input compensates for voltage drop between the module and the load and must be connected to VO close to the load for optimal accuracy. |
| 6 | -Sense | input | The sense input compensates for voltage drop between the module and the load and must be connected to GND (pin 3) very close to the module, within 10 cm. |
| 7 | VO Adjust | input | A 1%, 0.05 W resistor connected between this pin and -Sense (pin 6) sets the output voltage above 0.69 V, with a setpoint range of 0.69 V to 3.6 V, and the output defaults to its lowest value if left open. |
| 8 | TurboTrans | input | A 1%, 0.05 W resistor connected between this pin and +Sense (pin 5) activates TurboTrans, and the pin must be left open-circuit if unused, with no external capacitance connected unless the resistor is a 0 Ω short. |
| 9 | Track | input | This analog control input makes the output follow an external voltage volt-for-volt from 0 V up to the set-point voltage, becoming active about 20 ms after input voltage is applied, and should be connected to VI if unused. |
| 10 | Inhibit/UVLO | input | This open-collector/drain negative-logic input disables the output when pulled to GND and also sets the input undervoltage lockout threshold through a resistor to GND (pin 3), and it is open for normal operation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | DIP-10 |
| Category | Power Supply Chip |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output current | IO | 0 | 6 | A | Over VO range; 25°C, natural convection | 6 | |
| Input voltage range | VI | 2.2 | 5.5 | V | 0.69 ≤ VO ≤ 1.7, over IO range | 6 | |
| Input voltage range | VI | 5.5 | V | 1.7 < VO ≤ 3.6; minimum is VO+0.5 V (note 1) | 6 | ||
| Output voltage adjust range | VOADJ | 0.69 | 3.6 | V | Over IO range | 6 | |
| Set-point voltage tolerance | -1 | 0.5 | 1 | %Vo | RSET 1% with 100 ppm/C or better temperature stability (note 2) | 6 | |
| Temperature variation | -0.3 | 0.3 | %Vo | -40°C < TA < 85°C | 6 | ||
| Line regulation | VO | -2 | 2 | mV | Over VI range | 6 | |
| Load regulation | VO | -2 | 2 | mV | Over IO range | 6 | |
| Total output variation | VO | -1.5 | 1.5 | %Vo | Includes set-point, line, load, -40°C ≤ TA ≤ 85°C | 6 | |
| Output ripple (peak-to-peak) | VO | 1 | %VO | 20-MHz bandwidth | 6 | ||
| Adjustable undervoltage lockout, increasing | UVLOADJ | 1.95 | 2.19 | V | VI increasing, RUVLO = OPEN (pin 10) | 6 | |
| Adjustable undervoltage lockout, decreasing | UVLOADJ | 1.3 | 1.5 | V | VI decreasing, RUVLO = OPEN (pin 10) | 6 | |
| Inhibit control input low voltage | VIL | -0.2 | 0.8 | V | Inhibit control (pin 10) | 6 | |
| Synchronization (SYNC) frequency | fSYNC | 240 | 400 | kHz | SYNC frequency range | 6 | |
| SYNC high-level input voltage | VSYNCH | 2 | 5.5 | V | 6 | ||
| SYNC low-level input voltage | VSYNCL | 0.8 | V | 6 | |||
| SYNC minimum pulse width | tSYNC | 200 | nSec | 6 | |||
| External input capacitance | CI | 300 | µF | Ceramic; 300 µF of ceramic input capacitance is required (note 5) | 6 | ||
| External output capacitance, without TurboTrans | CO | 300 | 5000 | µF | Ceramic, w/o TurboTrans | 7 | |
| External output capacitance, with TurboTrans | CO | 5000 | µF | w/ TurboTrans, capacitance value | 7 | ||
| Capacitance × ESR product | CO × ESR | 100 | 1000 | µF×mΩ | w/ TurboTrans | 7 | |
| Track pin voltage | VTrack | -0.3 | V | Upper limit VI + 0.3 V; voltages with respect to GND | 3 | ||
| Operating temperature range | TA | -40 | 85 | °C | Over VI range | 3 | |
| Storage temperature | Tstg | -55 | 125 | °C | Storage temperature of module removed from shipping package | 3 | |
| Packaging temperature | Tpkg | 45 | °C | Shipping tray or tape and reel storage or bake temperature | 3 | ||
| Wave soldering temperature | Twave | 260 | °C | AD suffix; surface temperature of module body or pins, 5 seconds maximum | 3 | ||
| Mechanical shock | 500 | G | Per Mil-STD-883D, Method 2002.3, 1 msec, 1/2 sine, mounted; suffix AD | 3 | |||
| Mechanical vibration | 20 | G | Mil-STD-883D, Method 2007.2, 20-2000 Hz; suffix AD | 3 |
CAD (KiCad official)
- Symbol:
PTH04T231WAD - Footprint:
Package_DIP:DIP-10_W7.62mm - 3D model: DIP-10 (KiCad packages3D, STEP)
- 3D model files:
pth04t231wad-etched.step/pth04t231wad-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pth04t231wad.step/pth04t231wad.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (36 pp, sha256
240c8c9b0b51d6d7, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).