Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

PTH04T231WAD

Texas Instruments · Power Modules · DIP-10

PTH04T231WAD from Texas Instruments, in a DIP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SmartSync input This input pin synchronizes the module's switching frequency to an external clock, and if unused it should be connected to GND (pin 3).
2 VI power_in The positive input voltage power node to the module, referenced to common GND, with an input range of 2.2 V to 5.5 V.
3 GND power_in This is the common ground connection for the VI and VO power connections and the 0 Vdc reference for the control inputs.
4 VO power_out The regulated positive power output with respect to GND, adjustable from 0.69 V to 3.6 V.
5 +Sense input The sense input compensates for voltage drop between the module and the load and must be connected to VO close to the load for optimal accuracy.
6 -Sense input The sense input compensates for voltage drop between the module and the load and must be connected to GND (pin 3) very close to the module, within 10 cm.
7 VO Adjust input A 1%, 0.05 W resistor connected between this pin and -Sense (pin 6) sets the output voltage above 0.69 V, with a setpoint range of 0.69 V to 3.6 V, and the output defaults to its lowest value if left open.
8 TurboTrans input A 1%, 0.05 W resistor connected between this pin and +Sense (pin 5) activates TurboTrans, and the pin must be left open-circuit if unused, with no external capacitance connected unless the resistor is a 0 Ω short.
9 Track input This analog control input makes the output follow an external voltage volt-for-volt from 0 V up to the set-point voltage, becoming active about 20 ms after input voltage is applied, and should be connected to VI if unused.
10 Inhibit/UVLO input This open-collector/drain negative-logic input disables the output when pulled to GND and also sets the input undervoltage lockout threshold through a resistor to GND (pin 3), and it is open for normal operation.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package DIP-10
Category Power Supply Chip
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Output current IO 0 6 A Over VO range; 25°C, natural convection 6
Input voltage range VI 2.2 5.5 V 0.69 ≤ VO ≤ 1.7, over IO range 6
Input voltage range VI 5.5 V 1.7 < VO ≤ 3.6; minimum is VO+0.5 V (note 1) 6
Output voltage adjust range VOADJ 0.69 3.6 V Over IO range 6
Set-point voltage tolerance -1 0.5 1 %Vo RSET 1% with 100 ppm/C or better temperature stability (note 2) 6
Temperature variation -0.3 0.3 %Vo -40°C < TA < 85°C 6
Line regulation VO -2 2 mV Over VI range 6
Load regulation VO -2 2 mV Over IO range 6
Total output variation VO -1.5 1.5 %Vo Includes set-point, line, load, -40°C ≤ TA ≤ 85°C 6
Output ripple (peak-to-peak) VO 1 %VO 20-MHz bandwidth 6
Adjustable undervoltage lockout, increasing UVLOADJ 1.95 2.19 V VI increasing, RUVLO = OPEN (pin 10) 6
Adjustable undervoltage lockout, decreasing UVLOADJ 1.3 1.5 V VI decreasing, RUVLO = OPEN (pin 10) 6
Inhibit control input low voltage VIL -0.2 0.8 V Inhibit control (pin 10) 6
Synchronization (SYNC) frequency fSYNC 240 400 kHz SYNC frequency range 6
SYNC high-level input voltage VSYNCH 2 5.5 V 6
SYNC low-level input voltage VSYNCL 0.8 V 6
SYNC minimum pulse width tSYNC 200 nSec 6
External input capacitance CI 300 µF Ceramic; 300 µF of ceramic input capacitance is required (note 5) 6
External output capacitance, without TurboTrans CO 300 5000 µF Ceramic, w/o TurboTrans 7
External output capacitance, with TurboTrans CO 5000 µF w/ TurboTrans, capacitance value 7
Capacitance × ESR product CO × ESR 100 1000 µF×mΩ w/ TurboTrans 7
Track pin voltage VTrack -0.3 V Upper limit VI + 0.3 V; voltages with respect to GND 3
Operating temperature range TA -40 85 °C Over VI range 3
Storage temperature Tstg -55 125 °C Storage temperature of module removed from shipping package 3
Packaging temperature Tpkg 45 °C Shipping tray or tape and reel storage or bake temperature 3
Wave soldering temperature Twave 260 °C AD suffix; surface temperature of module body or pins, 5 seconds maximum 3
Mechanical shock 500 G Per Mil-STD-883D, Method 2002.3, 1 msec, 1/2 sine, mounted; suffix AD 3
Mechanical vibration 20 G Mil-STD-883D, Method 2007.2, 20-2000 Hz; suffix AD 3

CAD (KiCad official)

  • Symbol: PTH04T231WAD
  • Footprint: Package_DIP:DIP-10_W7.62mm
  • 3D model: DIP-10 (KiCad packages3D, STEP)
  • 3D model files: pth04t231wad-etched.step / pth04t231wad-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); pth04t231wad.step / pth04t231wad.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (36 pp, sha256 240c8c9b0b51d6d7, retrieved 2026-11-21)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF