main
History Download
Ray Publish 0.1.0 d21d996

PTH04T230WAD

Texas Instruments · Power Modules · DIP-10

PTH04T230WAD from Texas Instruments, in a DIP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SmartSync input Synchronizes the module switching frequency to an external clock (SYNC high level 2 V to 5.5 V, low level up to 0.8 V, minimum pulse width 200 ns); if unused, connect to GND (pin 3).
2 VI power_in Positive input voltage power node, referenced to common GND, specified for 2.2 V to 5.5 V input.
3 GND power_in Common ground for the VI and VO power connections and the 0 Vdc reference for the control inputs.
4 VO power_out Regulated positive power output with respect to GND, adjustable from 0.69 V to 3.6 V.
5 +Sense input Sense input that compensates for voltage drop between module and load; for optimal accuracy connect to VO close to the load.
6 -Sense input Sense input that compensates for voltage drop between module and load; for optimal accuracy connect to GND (pin 3) very close to the module, within 10 cm.
7 VO Adjust input A 1%, 0.05 W resistor connected directly between this pin and -Sense (pin 6) sets the output to a value above 0.69 V (resistor temperature stability 100 ppm/°C or better); if left open the output defaults to its lowest value of 0.69 V.
8 TurboTrans input A 1%, 0.05 W resistor connected between this pin and +Sense (pin 5), very close to the module, activates TurboTrans; if unused it must be left open-circuit, and no external capacitance may be connected unless the resistor is a 0 Ω short.
9 Track input Analog control input that makes the output follow an external voltage volt-for-volt from 0 V up to the set-point voltage, becoming active about 20 ms after VI is applied; if unused, connect to VI.
10 Inhibit/UVLO input Open-collector/drain, negative-logic inhibit input referenced to GND (ground disables the output, open enables it, with an internal pull-up that must not have an external pull-up added), and also the input undervoltage lockout programming pin where a resistor to GND raises the UVLO ON threshold.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package DIP-10
Category Power Supply Chip
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Output current IO 0 6 A Over VO range; 25°C, natural convection 4
Input voltage range (0.69 ≤ VO ≤ 1.7) VI 2.2 5.5 V 0.69 ≤ VO ≤ 1.7; over IO range 4
Input voltage range (1.7 < VO ≤ 3.6) VI 5.5 V 1.7 < VO ≤ 3.6; over IO range 4
Output adjust range 0.69 3.6 V Over IO range 4
Set-point voltage tolerance -1 0.5 1 %Vo RSET 1% with 200 ppm/°C or better (note 2) 4
Temperature variation -0.3 0.3 %Vo -40°C < TA < 85°C 4
Line regulation -2 2 mV Over VI range 4
Load regulation -2 2 mV Over IO range 4
Total output variation -1.5 1.5 %VO Includes set-point, line, load; -40°C ≤ TA ≤ 85°C 4
VO ripple (peak-to-peak) 1 %VO 20-MHz bandwidth 4
Adjustable undervoltage lockout, VI increasing UVLOADJ 1.95 2.19 V VI increasing, RUVLO = OPEN 4
Adjustable undervoltage lockout, VI decreasing UVLOADJ 1.3 1.5 V VI decreasing, RUVLO = OPEN 4
Input low voltage (inhibit control, pin 10) VIL -0.2 0.6 V 4
Switching frequency synchronization range (SYNC) fSYNC 240 400 kHz 4
SYNC high-level input voltage VSYNCH 2 5.5 V 4
SYNC low-level input voltage VSYNCL 0.8 V 4
SYNC minimum pulse width tSYNC 200 nSec 4
External input capacitance CI 330 µF 5
External input capacitance, nonceramic, without TurboTrans CI 150 5000 µF Nonceramic, without TurboTrans 5
External input capacitance, ceramic, without TurboTrans CI 100 500 µF Ceramic, without TurboTrans 5
Equivalent series resistance (non-ceramic) ESR 7 mΩ Non-ceramic 5
External output capacitance with TurboTrans CO 5000 µF With TurboTrans 5
Capacitance × ESR product (CO × ESR) CO × ESR 1000 10000 µF×mΩ 5
Track pin voltage (upper limit VI + 0.3 V) VTrack -0.3 V Referenced to GND 3
Operating temperature range TA -40 85 °C Over VI range 3
Wave soldering temperature Twave 260 °C AD suffix, 5 seconds maximum 3
Storage temperature Tstg -55 125 °C Storage temperature of module removed from shipping package 3
Packaging temperature Tpkg 45 °C Shipping tray or tape and reel storage or bake 3
Mechanical shock 500 G Per Mil-STD-883D Method 2002.3, 1 msec, 1/2 sine, mounted; suffix AD 3
Mechanical vibration 20 G Mil-STD-883D Method 2007.2, 20-2000 Hz; suffix AD 3
Overcurrent threshold ILIM 10 A Reset, followed by auto-recovery 4
Inhibit hysteresis 0.5 V RUVLO ≤ 52.3 kΩ 4
Input low current, pin 10 to GND IIL 125 µA Pin 10 to GND 4
Track input current (pin 9) IIL -130 µA Pin to GND 4
Input standby current Iin 5 mA Inhibit (pin 10) to GND, Track (pin 9) open 4
Track slew rate capability dVtrack/dt 1 V/ms CO ≤ CO(max) 4
Switching frequency fs 300 kHz Over VI and IO ranges, SmartSync (pin 1) to GND 4

CAD (KiCad official)

  • Symbol: PTH04T230WAD
  • Footprint: Package_DIP:DIP-10_W7.62mm
  • 3D model: DIP-10 (KiCad packages3D, STEP)
  • 3D model files: pth04t230wad-etched.step / pth04t230wad-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); pth04t230wad.step / pth04t230wad.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (36 pp, sha256 5b2e0295265ae960, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF