Generated by kicad-footprint-generator · KiCad file format 20260206
PTH04T230WAD
Texas Instruments · Power Modules · DIP-10
PTH04T230WAD from Texas Instruments, in a DIP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SmartSync | input | Synchronizes the module switching frequency to an external clock (SYNC high level 2 V to 5.5 V, low level up to 0.8 V, minimum pulse width 200 ns); if unused, connect to GND (pin 3). |
| 2 | VI | power_in | Positive input voltage power node, referenced to common GND, specified for 2.2 V to 5.5 V input. |
| 3 | GND | power_in | Common ground for the VI and VO power connections and the 0 Vdc reference for the control inputs. |
| 4 | VO | power_out | Regulated positive power output with respect to GND, adjustable from 0.69 V to 3.6 V. |
| 5 | +Sense | input | Sense input that compensates for voltage drop between module and load; for optimal accuracy connect to VO close to the load. |
| 6 | -Sense | input | Sense input that compensates for voltage drop between module and load; for optimal accuracy connect to GND (pin 3) very close to the module, within 10 cm. |
| 7 | VO Adjust | input | A 1%, 0.05 W resistor connected directly between this pin and -Sense (pin 6) sets the output to a value above 0.69 V (resistor temperature stability 100 ppm/°C or better); if left open the output defaults to its lowest value of 0.69 V. |
| 8 | TurboTrans | input | A 1%, 0.05 W resistor connected between this pin and +Sense (pin 5), very close to the module, activates TurboTrans; if unused it must be left open-circuit, and no external capacitance may be connected unless the resistor is a 0 Ω short. |
| 9 | Track | input | Analog control input that makes the output follow an external voltage volt-for-volt from 0 V up to the set-point voltage, becoming active about 20 ms after VI is applied; if unused, connect to VI. |
| 10 | Inhibit/UVLO | input | Open-collector/drain, negative-logic inhibit input referenced to GND (ground disables the output, open enables it, with an internal pull-up that must not have an external pull-up added), and also the input undervoltage lockout programming pin where a resistor to GND raises the UVLO ON threshold. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | DIP-10 |
| Category | Power Supply Chip |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output current | IO | 0 | 6 | A | Over VO range; 25°C, natural convection | 4 | |
| Input voltage range (0.69 ≤ VO ≤ 1.7) | VI | 2.2 | 5.5 | V | 0.69 ≤ VO ≤ 1.7; over IO range | 4 | |
| Input voltage range (1.7 < VO ≤ 3.6) | VI | 5.5 | V | 1.7 < VO ≤ 3.6; over IO range | 4 | ||
| Output adjust range | 0.69 | 3.6 | V | Over IO range | 4 | ||
| Set-point voltage tolerance | -1 | 0.5 | 1 | %Vo | RSET 1% with 200 ppm/°C or better (note 2) | 4 | |
| Temperature variation | -0.3 | 0.3 | %Vo | -40°C < TA < 85°C | 4 | ||
| Line regulation | -2 | 2 | mV | Over VI range | 4 | ||
| Load regulation | -2 | 2 | mV | Over IO range | 4 | ||
| Total output variation | -1.5 | 1.5 | %VO | Includes set-point, line, load; -40°C ≤ TA ≤ 85°C | 4 | ||
| VO ripple (peak-to-peak) | 1 | %VO | 20-MHz bandwidth | 4 | |||
| Adjustable undervoltage lockout, VI increasing | UVLOADJ | 1.95 | 2.19 | V | VI increasing, RUVLO = OPEN | 4 | |
| Adjustable undervoltage lockout, VI decreasing | UVLOADJ | 1.3 | 1.5 | V | VI decreasing, RUVLO = OPEN | 4 | |
| Input low voltage (inhibit control, pin 10) | VIL | -0.2 | 0.6 | V | 4 | ||
| Switching frequency synchronization range (SYNC) | fSYNC | 240 | 400 | kHz | 4 | ||
| SYNC high-level input voltage | VSYNCH | 2 | 5.5 | V | 4 | ||
| SYNC low-level input voltage | VSYNCL | 0.8 | V | 4 | |||
| SYNC minimum pulse width | tSYNC | 200 | nSec | 4 | |||
| External input capacitance | CI | 330 | µF | 5 | |||
| External input capacitance, nonceramic, without TurboTrans | CI | 150 | 5000 | µF | Nonceramic, without TurboTrans | 5 | |
| External input capacitance, ceramic, without TurboTrans | CI | 100 | 500 | µF | Ceramic, without TurboTrans | 5 | |
| Equivalent series resistance (non-ceramic) | ESR | 7 | mΩ | Non-ceramic | 5 | ||
| External output capacitance with TurboTrans | CO | 5000 | µF | With TurboTrans | 5 | ||
| Capacitance × ESR product (CO × ESR) | CO × ESR | 1000 | 10000 | µF×mΩ | 5 | ||
| Track pin voltage (upper limit VI + 0.3 V) | VTrack | -0.3 | V | Referenced to GND | 3 | ||
| Operating temperature range | TA | -40 | 85 | °C | Over VI range | 3 | |
| Wave soldering temperature | Twave | 260 | °C | AD suffix, 5 seconds maximum | 3 | ||
| Storage temperature | Tstg | -55 | 125 | °C | Storage temperature of module removed from shipping package | 3 | |
| Packaging temperature | Tpkg | 45 | °C | Shipping tray or tape and reel storage or bake | 3 | ||
| Mechanical shock | 500 | G | Per Mil-STD-883D Method 2002.3, 1 msec, 1/2 sine, mounted; suffix AD | 3 | |||
| Mechanical vibration | 20 | G | Mil-STD-883D Method 2007.2, 20-2000 Hz; suffix AD | 3 | |||
| Overcurrent threshold | ILIM | 10 | A | Reset, followed by auto-recovery | 4 | ||
| Inhibit hysteresis | 0.5 | V | RUVLO ≤ 52.3 kΩ | 4 | |||
| Input low current, pin 10 to GND | IIL | 125 | µA | Pin 10 to GND | 4 | ||
| Track input current (pin 9) | IIL | -130 | µA | Pin to GND | 4 | ||
| Input standby current | Iin | 5 | mA | Inhibit (pin 10) to GND, Track (pin 9) open | 4 | ||
| Track slew rate capability | dVtrack/dt | 1 | V/ms | CO ≤ CO(max) | 4 | ||
| Switching frequency | fs | 300 | kHz | Over VI and IO ranges, SmartSync (pin 1) to GND | 4 |
CAD (KiCad official)
- Symbol:
PTH04T230WAD - Footprint:
Package_DIP:DIP-10_W7.62mm - 3D model: DIP-10 (KiCad packages3D, STEP)
- 3D model files:
pth04t230wad-etched.step/pth04t230wad-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pth04t230wad.step/pth04t230wad.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (36 pp, sha256
5b2e0295265ae960, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).