Generated by kicad-footprint-generator · KiCad file format 20260206
PT7C433833UEX
Diodes Incorporated · Real-time Clocks (RTC) · MSOP-8
PT7C433833UEX from Diodes Incorporated, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | X1 | input | Input to the internal 32.768kHz oscillator, designed for a crystal with a specified load capacitance of 12.5pF, and can alternatively be driven by an external 32.768kHz oscillator. |
| 2 | X2 | output | Output of the internal 32.768kHz oscillator, which is left floating when an external oscillator is connected to X1. |
| 3 | VBAT | power_in | Backup supply input for a standard 3V lithium cell or other energy source, which must be held between 1.5V and 3.7V for proper operation, or grounded if no backup is required. |
| 4 | GND | power_in | Ground reference for the device; all voltages are referenced to this pin. |
| 5 | SDA | bidirectional | Serial data input/output of the 2-wire I2C interface, which is open drain and requires an external pull-up resistor. |
| 6 | SCL | input | Serial clock input that synchronizes data movement on the I2C interface, with a maximum clock frequency of 400kHz. |
| 7 | SQW/OUT | output | Open-drain square-wave output, selectable as 1Hz, 4.096kHz, 8.192kHz or 32.768kHz when enabled, that requires an external pull-up resistor and operates with either VCC or VBAT applied. |
| 8 | VCC | power_in | Primary supply pin with a recommended operating range of 2.7V to 5.5V; when a backup supply is connected and VCC falls below VPF, reads and writes are inhibited while timekeeping continues. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Diodes Incorporated |
| Package | MSOP-8 |
| Category | Clock and Timing |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VCC | 2.7 | 3.3 | 5.5 | V | 3 | |
| Logic 0 Input Voltage | VIL | -0.3 | V | Note 2 | 3 | ||
| VBAT Battery Voltage | VBAT | 1.5 | 3 | 3.7 | V | Note 2 | 3 |
| VBAT Battery Voltage | VBAT | 1.5 | 3.7 | V | Note 2 | 4 | |
| Input Leakage | ILI | 1 | μA | Note 3 (SCL only) | 4 | ||
| I/O Leakage | ILO | 1 | μA | Note 4 (SDA and SQW/OUT) | 4 | ||
| SDA Logic 0 Output | IOLSDA | 3 | mA | VCC > 2V; VOL = 0.4V | 4 | ||
| SQW/OUT Logic 0 Output | IOLSQW | 3 | mA | VCC > 2V; VOL = 0.4V | 4 | ||
| SQW/OUT Logic 0 Output | IOLSQW | 250 | μA | 1.5V < VCC < 1.71V; VOL = 0.2 VCC | 4 | ||
| Active Supply Current | ICCA | 120 | 200 | μA | Note 5 (SCL clocking at max frequency = 400kHz) | 4 | |
| Standby Current | ICCS | 85 | 125 | μA | Note 6 (I2C bus inactive) | 4 | |
| VBAT Leakage Current (VCC Active) | IBATLKG | 25 | 100 | nA | 4 | ||
| VBAT Current (OSC ON), SQW/OUT OFF | IBATOSC1 | 400 | 1200 | nA | VBAT =3.7V, SQW/OUT OFF (Note 7) | 4 | |
| VBAT Current (OSC ON), SQW/OUT ON (32kHz) | IBATOSC2 | 570 | 1400 | nA | VBAT =3.7V, SQW/OUT ON (32kHz) (Note 7) | 4 | |
| VBAT Data-Retention Current (OSC OFF) | IBATDAT | 300 | nA | VBAT =3.7V (Note 7) | 4 | ||
| SCL Clock Frequency | fSCL | 100 | 400 | kHz | Fast mode | 5 | |
| SCL Clock Frequency | fSCL | 100 | kHz | Standard mode | 5 | ||
| Bus Free Time Between STOP and START condition | tBUF | 1.3 | μs | Fast mode | 5 | ||
| Bus Free Time Between STOP and START condition | tBUF | 4.7 | μs | Standard mode | 5 | ||
| Hold Time (Repeated) START Condition | tHD:STA | 0.6 | μs | Fast mode | 5 | ||
| Hold Time (Repeated) START Condition | tHD:STA | 4 | μs | Standard mode | 5 | ||
| LOW Period of SCL Clock | tLOW | 1.3 | μs | Fast mode | 5 | ||
| LOW Period of SCL Clock | tLOW | 4.7 | μs | Standard mode | 5 | ||
| HIGH Period of SCL Clock | tHIGH | 0.6 | μs | Fast mode | 5 | ||
| HIGH Period of SCL Clock | tHIGH | 4 | μs | Standard mode | 5 | ||
| Setup Time of Repeated START Condition | tSU:STA | 0.6 | μs | Fast mode | 5 | ||
| Setup Time of Repeated START Condition | tSU:STA | 4.7 | μs | Standard mode | 5 | ||
| Data Hold Time (Note 3, 4) | tHD:STA | 0 | 0.9 | μs | Fast mode; Note 3, 4 | 5 | |
| Data Hold Time (Note 3, 4) | tHD:STA | 0 | μs | Standard mode; Note 3, 4 | 5 | ||
| Data Setup Time (Note 5) | tSU:STA | 100 | ns | Fast mode; Note 5 | 5 | ||
| Data Setup Time (Note 5) | tSU:STA | 250 | ns | Standard mode; Note 5 | 5 | ||
| Rise Time of Both SDA and SCL Signals (Note 6) | tr | 300 | ns | Fast mode; Note 6 | 5 | ||
| Rise Time of Both SDA and SCL Signals (Note 6) | tr | 1000 | ns | Standard mode; Note 6 | 5 | ||
| Fall Time of Both SDA and SCL Signals (Note 6) | tf | 300 | ns | Fast mode; Note 6 | 5 | ||
| Setup Time for STOP Condition | tSU:STO | 0.6 | μs | Fast mode | 5 | ||
| Setup Time for STOP Condition | tSU:STO | 4 | μs | Standard mode | 5 | ||
| Capacitance Load for Each Bus Line | CB | 400 | pF | Note 6 | 5 | ||
| I/O Capacitance (SDA, SCL) | CI/O | 10 | pF | Note 1 | 5 | ||
| Recovery at Power-Up | tREC | 2 | ms | Note 2 | 6 | ||
| VCC Fall Time: VPF(MAX) to VPF(MIN) | tVCCF | 300 | μs | 6 | |||
| VCC Rise Time: VPF(MIN) to VPF(MAX) | tVCCR | 0 | μs | 6 | |||
| Storage Temperature | -55 | 125 | oC | 3 | |||
| Ambient Temperature with Power Applied | -40 | 85 | oC | 3 | |||
| Supply Voltage to Ground Potential (Vcc to GND) | -0.3 | 6.5 | V | 3 | |||
| DC Input (All Other Inputs except Vcc & GND) | -0.3 | 6.5 | V | 3 | |||
| DC Output Voltage (SDA, /INTA, /INTB pins) | -0.3 | 6.5 | V | 3 | |||
| Series Resistance | ESR | 70 | k | 7 | |||
| Power-Fail Voltage | VPF | 2.59 | V | PT7C433833 | 3 | ||
| Nominal Frequency | fO | 32.768 | kHz | 7 | |||
| Load Capacitance | CL | 12.5 | pF | 7 | |||
| Built-in capacitor X1 to GND | CG | 20 | pF | 7 | |||
| Built-in capacitor X2 to GND | CD | 20 | pF | 7 | |||
| Recommended external capacitor X1 to GND | C1 | 4 | pF | 7 | |||
| Recommended external capacitor X2 to GND | C2 | 4 | pF | 7 | |||
| Oscillator Stop Flag (OSF) Delay | tOSF | 100 | ms | Note 7 | 5 |
CAD (KiCad official)
- Symbol:
PT7C433833UEX - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
pt7c433833uex-etched.step/pt7c433833uex-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pt7c433833uex.step/pt7c433833uex.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Diodes Incorporated datasheet (17 pp, sha256
ecdcb338440e50e6, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).