main
Ray
Publish 0.1.0
389efc4
PMS152-S14
PADAUK Tech · Microcontroller Units (MCUs/MPUs/SOCs) · SOP-14
PMS152-S14 from PADAUK Tech, in a SOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PB5/PG0PWM/INT0A | bidirectional | Bit 5 of port B, digital input or two-state output with optional pull-up; also PWMG0 output and external interrupt line 0A (both edges, configurable), 5mA drive/30mA sink. |
| 2 | PB6/CIN4-/PG1PWM | bidirectional | Bit 6 of port B, digital I/O with optional pull-up; also comparator minus input 4 and PWMG1 output, with pbdier bit 6 set to 0 to prevent leakage when analog. |
| 3 | PB7/CIN5-/PG1PWM | bidirectional | Bit 7 of port B, digital I/O with optional pull-up; also comparator minus input 5 and PWMG1 output, 5mA drive/30mA sink, with pbdier bit 7 set to 0 when analog. |
| 4 | VDD | power_in | Positive power supply, operating range 1.8V to 5.5V. |
| 5 | PA7/X1 | bidirectional | Bit 7 of port A, input or output with pull-up; also crystal XIN, with padier bit 7 programmed to 0 when used for the crystal to avoid leakage. |
| 6 | PA6/X2 | bidirectional | Bit 6 of port A, input or output with pull-up; also crystal XOUT, with padier bit 6 programmed to 0 when used for the crystal to avoid leakage. |
| 7 | PRSTB | input | Shown as PRSTB on the SOP14 drawing; this is the PA5/PRSTB/PG2PWM pin, an input or open-drain output (10mA sink) that serves as hardware reset and PWMG2 output, with a 33 ohm series resistor advised in input mode. |
| 8 | PA3/CIN0-/TM2PWM/PG2PWM | bidirectional | Bit 3 of port A, digital I/O with optional pull-up; also comparator minus input 0, Timer2 PWM output and PWMG2 output, with padier bit 3 set to 0 when analog. |
| 9 | PA4/CIN+/CIN1-/INT1A/PG1PWM | bidirectional | Bit 4 of port A, digital I/O with optional pull-up; also comparator plus input, comparator minus input 1, external interrupt 1A and PWMG1 output, with padier bit 4 set to 0 when analog. |
| 10 | PA0/CO/PG0PWM/INT0 | bidirectional | Bit 0 of port A, digital I/O with optional pull-up; also comparator output, PWMG0 output and external interrupt line 0 (both edges, configurable). |
| 11 | GND | power_in | Ground. |
| 12 | PB0/INT1 | bidirectional | Bit 0 of port B, digital I/O with optional pull-up; also external interrupt line 1 (both edges, configurable). |
| 13 | PB1 | bidirectional | Bit 1 of port B, digital input or two-state output with optional pull-up resistor. |
| 14 | PB2/TM2PWM/PG2PWM | bidirectional | Bit 2 of port B, digital I/O with optional pull-up; also Timer2 PWM output and PWMG2 output. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | PADAUK Tech |
| Package | SOP-14 |
| Category | Embedded Processors & Controllers |
| Pins | 14 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD Operating Voltage | VDD | 1.8 | 5 | 5.5 | V | * Subject to LVR tolerance | 16 |
| Low Voltage Reset Tolerance | LVR% | -5 | 5 | % | 16 | ||
| System clock (CLK) = IHRC/2 | fSYS | 0 | 8 | MHz | VDD ≧ 3.5V | 16 | |
| System clock (CLK) = IHRC/4 | fSYS | 0 | 4 | MHz | VDD ≧ 2.5V | 16 | |
| System clock (CLK) = IHRC/8 | fSYS | 0 | 2 | MHz | VDD ≧ 1.8V | 16 | |
| Power On Reset Voltage | VPOR | 1.8 | V | * Subject to LVR tolerance | 16 | ||
| Operating Current (fSYS=IHRC/16) | IOP | 1 | mA | fSYS=IHRC/16=[email protected] | 16 | ||
| Operating Current (fSYS=ILRC) | IOP | 15 | uA | fSYS=ILRC=[email protected] | 16 | ||
| Power Down Current (stopsys) | IPD | 1 | uA | fSYS= 0Hz, VDD =5.0V | 16 | ||
| Power Down Current (stopsys) | IPD | 0.6 | uA | fSYS= 0Hz, VDD =3.3V | 16 | ||
| Power Save Current (stopexe) | IPS | 5 | uA | VDD =5.0V; fSYS= ILRC; only ILRC module is enabled | 16 | ||
| Input low voltage for IO lines (PA5) | VIL | 0 | 0.1 | x VDD | 16 | ||
| Input low voltage for IO lines (others) | VIL | 0 | 0.2 | x VDD | 16 | ||
| Input high voltage for IO lines (PA5) | VIH | 0.8 | x VDD | 16 | |||
| Input high voltage for IO lines (others) | VIH | 0.7 | x VDD | 16 | |||
| IO lines sink current (PA7, PA6, PA5, PA4, PA3, PA0) | IOL | 10 | mA | VDD=5.0V, VOL=0.5V | 16 | ||
| IO lines sink current (PB6, PB4, PB2, PB1, PB0) | IOL | 10 | mA | VDD=5.0V, VOL=0.5V | 16 | ||
| IO lines sink current (PB7, PB5, PB3) | IOL | 30 | mA | VDD=5.0V, VOL=0.5V | 16 | ||
| IO lines drive current (PA5) | IOH | 0 | mA | VDD=5.0V, VOH=4.5V | 16 | ||
| IO lines drive current (PA7, PA6, PA4, PA3, PA0) | IOH | -5 | mA | VDD=5.0V, VOH=4.5V | 16 | ||
| IO lines drive current (PB7, PB6, PB5, PB4, PB3) | IOH | -5 | mA | VDD=5.0V, VOH=4.5V | 16 | ||
| IO lines drive current (PB2, PB1, PB0) | IOH | -5 | mA | VDD=5.0V, VOH=4.5V | 16 | ||
| Input voltage | VIN | -0.3 | V | 16 | |||
| Injected current on pin | IINJ (PIN) | 1 | mA | VDD +0.3≧VIN≧ -0.3 | 16 | ||
| Band-gap Reference Voltage | VBG | 1.145 | 1.2 | 1.255 | V | VDD =2.2V ~ 5.5V | 16 |
| Frequency of IHRC after calibration | fIHRC | 15.76 | 16 | 16.24 | MHz | 25oC, VDD =2.2V~5.5V | 16 |
| Frequency of IHRC after calibration | fIHRC | 15.2 | 16 | 16.8 | MHz | VDD =2.2V~5.5V, -20oC <Ta<70oC | 16 |
| Frequency of IHRC after calibration | fIHRC | 13.6 | 16 | 18.4 | MHz | VDD =1.8V~5.5V, -20oC <Ta<70oC | 16 |
| Interrupt pulse width | tINT | 30 | ns | VDD = 5.0V | 16 | ||
| RAM data retention voltage | VDR | 1.5 | V | in stop mode | 17 | ||
| Wake-up time period for fast wake-up | tWUP | 45 | TILRC | Where TILRC is the time period of ILRC | 17 | ||
| Wake-up time period for normal wake-up | tWUP | 3000 | TILRC | Where TILRC is the time period of ILRC | 17 | ||
| System boot-up period from power-on for Normal boot-up | tSBP | 55 | ms | VDD =5V | 17 | ||
| System boot-up period from power-on for Fast boot-up | tSBP | 820 | us | 17 | |||
| External reset pulse width | tRST | 120 | us | @ VDD =5V | 17 | ||
| Comparator offset | CPos | -20 | 10 | 20 | mV | 17 | |
| Comparator input common mode | CPcm | 0 | V | 17 | |||
| Comparator response time | CPspt | 100 | 500 | ns | Both Rising and Falling | 17 | |
| Stable time to change comparator mode | CPmc | 2.5 | 7.5 | us | 17 | ||
| Comparator current consumption | CPcs | 20 | uA | VDD = 3.3V | 17 | ||
| Supply Voltage (maximum rating) | VDD | 5.5 | V | 17 | |||
| Operating Temperature | TA | -20 | 70 | °C | 17 | ||
| Storage Temperature | TSTG | -50 | 125 | °C | 17 | ||
| Junction Temperature | TJ | 150 | °C | 17 | |||
| System clock (CLK) = ILRC | fSYS | 55 | kHz | VDD = 3.0V | 16 | ||
| Pull-high Resistance | RPH | 100 | KΩ | VDD =5.0V | 16 | ||
| Pull-high Resistance | RPH | 200 | KΩ | VDD =3.0V | 16 |
CAD (KiCad official)
- Symbol:
PMS152-S14 - Footprint:
Package_SO:SOIC-14_3.9x8.7mm_P1.27mm - 3D model: SOP-14 (KiCad packages3D, STEP)
- 3D model files:
pms152-s14-etched.step/pms152-s14-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pms152-s14.step/pms152-s14.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: PADAUK Tech datasheet (87 pp, sha256
cf25bfc11ccaa8a5, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# PMS152-S14
**PADAUK Tech** · Microcontroller Units (MCUs/MPUs/SOCs) · SOP-14
PMS152-S14 from PADAUK Tech, in a SOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PB5/PG0PWM/INT0A | bidirectional | Bit 5 of port B, digital input or two-state output with optional pull-up; also PWMG0 output and external interrupt line 0A (both edges, configurable), 5mA drive/30mA sink. |
| 2 | PB6/CIN4-/PG1PWM | bidirectional | Bit 6 of port B, digital I/O with optional pull-up; also comparator minus input 4 and PWMG1 output, with pbdier bit 6 set to 0 to prevent leakage when analog. |
| 3 | PB7/CIN5-/PG1PWM | bidirectional | Bit 7 of port B, digital I/O with optional pull-up; also comparator minus input 5 and PWMG1 output, 5mA drive/30mA sink, with pbdier bit 7 set to 0 when analog. |
| 4 | VDD | power_in | Positive power supply, operating range 1.8V to 5.5V. |
| 5 | PA7/X1 | bidirectional | Bit 7 of port A, input or output with pull-up; also crystal XIN, with padier bit 7 programmed to 0 when used for the crystal to avoid leakage. |
| 6 | PA6/X2 | bidirectional | Bit 6 of port A, input or output with pull-up; also crystal XOUT, with padier bit 6 programmed to 0 when used for the crystal to avoid leakage. |
| 7 | PRSTB | input | Shown as PRSTB on the SOP14 drawing; this is the PA5/PRSTB/PG2PWM pin, an input or open-drain output (10mA sink) that serves as hardware reset and PWMG2 output, with a 33 ohm series resistor advised in input mode. |
| 8 | PA3/CIN0-/TM2PWM/PG2PWM | bidirectional | Bit 3 of port A, digital I/O with optional pull-up; also comparator minus input 0, Timer2 PWM output and PWMG2 output, with padier bit 3 set to 0 when analog. |
| 9 | PA4/CIN+/CIN1-/INT1A/PG1PWM | bidirectional | Bit 4 of port A, digital I/O with optional pull-up; also comparator plus input, comparator minus input 1, external interrupt 1A and PWMG1 output, with padier bit 4 set to 0 when analog. |
| 10 | PA0/CO/PG0PWM/INT0 | bidirectional | Bit 0 of port A, digital I/O with optional pull-up; also comparator output, PWMG0 output and external interrupt line 0 (both edges, configurable). |
| 11 | GND | power_in | Ground. |
| 12 | PB0/INT1 | bidirectional | Bit 0 of port B, digital I/O with optional pull-up; also external interrupt line 1 (both edges, configurable). |
| 13 | PB1 | bidirectional | Bit 1 of port B, digital input or two-state output with optional pull-up resistor. |
| 14 | PB2/TM2PWM/PG2PWM | bidirectional | Bit 2 of port B, digital I/O with optional pull-up; also Timer2 PWM output and PWMG2 output. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | PADAUK Tech |
| Package | SOP-14 |
| Category | Embedded Processors & Controllers |
| Pins | 14 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD Operating Voltage | VDD | 1.8 | 5 | 5.5 | V | * Subject to LVR tolerance | 16 |
| Low Voltage Reset Tolerance | LVR% | -5 | | 5 | % | | 16 |
| System clock (CLK) = IHRC/2 | fSYS | 0 | | 8 | MHz | VDD ≧ 3.5V | 16 |
| System clock (CLK) = IHRC/4 | fSYS | 0 | | 4 | MHz | VDD ≧ 2.5V | 16 |
| System clock (CLK) = IHRC/8 | fSYS | 0 | | 2 | MHz | VDD ≧ 1.8V | 16 |
| Power On Reset Voltage | VPOR | 1.8 | | | V | * Subject to LVR tolerance | 16 |
| Operating Current (fSYS=IHRC/16) | IOP | | | 1 | mA | fSYS=IHRC/[email protected] | 16 |
| Operating Current (fSYS=ILRC) | IOP | | | 15 | uA | [email protected] | 16 |
| Power Down Current (stopsys) | IPD | | | 1 | uA | fSYS= 0Hz, VDD =5.0V | 16 |
| Power Down Current (stopsys) | IPD | | | 0.6 | uA | fSYS= 0Hz, VDD =3.3V | 16 |
| Power Save Current (stopexe) | IPS | | | 5 | uA | VDD =5.0V; fSYS= ILRC; only ILRC module is enabled | 16 |
| Input low voltage for IO lines (PA5) | VIL | 0 | | 0.1 | x VDD | | 16 |
| Input low voltage for IO lines (others) | VIL | 0 | | 0.2 | x VDD | | 16 |
| Input high voltage for IO lines (PA5) | VIH | 0.8 | | | x VDD | | 16 |
| Input high voltage for IO lines (others) | VIH | 0.7 | | | x VDD | | 16 |
| IO lines sink current (PA7, PA6, PA5, PA4, PA3, PA0) | IOL | 10 | | | mA | VDD=5.0V, VOL=0.5V | 16 |
| IO lines sink current (PB6, PB4, PB2, PB1, PB0) | IOL | 10 | | | mA | VDD=5.0V, VOL=0.5V | 16 |
| IO lines sink current (PB7, PB5, PB3) | IOL | 30 | | | mA | VDD=5.0V, VOL=0.5V | 16 |
| IO lines drive current (PA5) | IOH | 0 | | | mA | VDD=5.0V, VOH=4.5V | 16 |
| IO lines drive current (PA7, PA6, PA4, PA3, PA0) | IOH | -5 | | | mA | VDD=5.0V, VOH=4.5V | 16 |
| IO lines drive current (PB7, PB6, PB5, PB4, PB3) | IOH | -5 | | | mA | VDD=5.0V, VOH=4.5V | 16 |
| IO lines drive current (PB2, PB1, PB0) | IOH | -5 | | | mA | VDD=5.0V, VOH=4.5V | 16 |
| Input voltage | VIN | -0.3 | | | V | | 16 |
| Injected current on pin | IINJ (PIN) | | | 1 | mA | VDD +0.3≧VIN≧ -0.3 | 16 |
| Band-gap Reference Voltage | VBG | 1.145 | 1.2 | 1.255 | V | VDD =2.2V ~ 5.5V | 16 |
| Frequency of IHRC after calibration | fIHRC | 15.76 | 16 | 16.24 | MHz | 25oC, VDD =2.2V~5.5V | 16 |
| Frequency of IHRC after calibration | fIHRC | 15.2 | 16 | 16.8 | MHz | VDD =2.2V~5.5V, -20oC <Ta<70oC | 16 |
| Frequency of IHRC after calibration | fIHRC | 13.6 | 16 | 18.4 | MHz | VDD =1.8V~5.5V, -20oC <Ta<70oC | 16 |
| Interrupt pulse width | tINT | 30 | | | ns | VDD = 5.0V | 16 |
| RAM data retention voltage | VDR | 1.5 | | | V | in stop mode | 17 |
| Wake-up time period for fast wake-up | tWUP | | | 45 | TILRC | Where TILRC is the time period of ILRC | 17 |
| Wake-up time period for normal wake-up | tWUP | | | 3000 | TILRC | Where TILRC is the time period of ILRC | 17 |
| System boot-up period from power-on for Normal boot-up | tSBP | | | 55 | ms | VDD =5V | 17 |
| System boot-up period from power-on for Fast boot-up | tSBP | | | 820 | us | | 17 |
| External reset pulse width | tRST | 120 | | | us | @ VDD =5V | 17 |
| Comparator offset | CPos | -20 | 10 | 20 | mV | | 17 |
| Comparator input common mode | CPcm | 0 | | | V | | 17 |
| Comparator response time | CPspt | | 100 | 500 | ns | Both Rising and Falling | 17 |
| Stable time to change comparator mode | CPmc | | 2.5 | 7.5 | us | | 17 |
| Comparator current consumption | CPcs | | | 20 | uA | VDD = 3.3V | 17 |
| Supply Voltage (maximum rating) | VDD | | | 5.5 | V | | 17 |
| Operating Temperature | TA | -20 | | 70 | °C | | 17 |
| Storage Temperature | TSTG | -50 | | 125 | °C | | 17 |
| Junction Temperature | TJ | | | 150 | °C | | 17 |
| System clock (CLK) = ILRC | fSYS | | 55 | | kHz | VDD = 3.0V | 16 |
| Pull-high Resistance | RPH | | 100 | | KΩ | VDD =5.0V | 16 |
| Pull-high Resistance | RPH | | 200 | | KΩ | VDD =3.0V | 16 |
## CAD (KiCad official)
- Symbol: `PMS152-S14`
- Footprint: `Package_SO:SOIC-14_3.9x8.7mm_P1.27mm`
- 3D model: SOP-14 (KiCad packages3D, STEP)
- 3D model files: `pms152-s14-etched.step` / `pms152-s14-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `pms152-s14.step` / `pms152-s14.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [PADAUK Tech datasheet](docs/pms152-s14-datasheet.pdf) (87 pp, sha256 `cf25bfc11ccaa8a5`, retrieved 2026-10-28, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text+vision), consensus `claude-opus-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/pms152-s14-datasheet.pdf)