3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownPIC18F67J60-I
Microchip Tech · MICROCHIP · TQFP-64(10x10)
PIC18F67J60-I from Microchip Tech, in a TQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RE1/P2C | bidirectional | Digital I/O with Schmitt Trigger input and weak pull-up enabled by REPU; also ECCP2 Enhanced PWM output C (P2C). |
| 2 | RE0/P2D | bidirectional | Digital I/O with Schmitt Trigger input and weak pull-up enabled by REPU; also ECCP2 Enhanced PWM output D (P2D). |
| 3 | RB0/INT0/FLT0 | bidirectional | Digital I/O with TTL input and weak pull-up when RBPU is cleared; also external interrupt 0 (Schmitt Trigger) and Enhanced PWM Fault input FLT0 enabled in software. |
| 4 | RB1/INT1 | bidirectional | Digital I/O with TTL input and weak pull-up when RBPU is cleared; also external interrupt 1 input (INT1). |
| 5 | RB2/INT2 | bidirectional | Digital I/O with TTL input and weak pull-up when RBPU is cleared; also external interrupt 2 input (INT2). |
| 6 | RB3/INT3 | bidirectional | Digital I/O with TTL input and weak pull-up when RBPU is cleared; also external interrupt 3 input (INT3). |
| 7 | MCLR | input | Master Clear (Reset) input; active-low Reset to the device. |
| 8 | RG4/CCP5/P1D | bidirectional | Digital I/O with Schmitt Trigger input; also CCP5 capture/compare/PWM pin and ECCP1 Enhanced PWM output D (P1D). |
| 9 | VSS | power_in | Ground reference for logic and I/O pins. |
| 10 | VDDCORE/VCAP | power_in | Core logic supply (VDDCORE) when the on-chip regulator is disabled; when the regulator is enabled this pin is the VCAP external filter capacitor connection and must use a 10 µF capacitor to ground and must not be connected to VDD. |
| 11 | RF7/SS1 | bidirectional | Digital I/O with Schmitt Trigger input; also SPI slave select input for MSSP1 (TTL). |
| 12 | RF6/AN11 | bidirectional | Digital I/O with Schmitt Trigger input (disabled when analog input is enabled); also analog input channel 11 and comparator C1- input. |
| 13 | RF5/AN10/CVREF | bidirectional | Digital I/O with Schmitt Trigger input; also analog input channel 10 (comparator C1+ input) and comparator voltage reference output CVREF. |
| 14 | RF4/AN9 | bidirectional | Digital I/O with Schmitt Trigger input (disabled when analog input is enabled); also analog input channel 9 and comparator C2- input. |
| 15 | RF3/AN8 | bidirectional | Digital I/O with Schmitt Trigger input (disabled when analog input is enabled); also analog input channel 8 and comparator C2+ input. |
| 16 | RF2/AN7/C1OUT | bidirectional | Digital I/O with Schmitt Trigger input (disabled when analog input is enabled); also analog input channel 7 and comparator 1 output C1OUT. |
| 17 | RF1/AN6/C2OUT | bidirectional | Digital I/O with Schmitt Trigger input (disabled when analog input is enabled); also analog input channel 6 and comparator 2 output C2OUT. |
| 18 | ENVREG | input | Enable for the on-chip voltage regulator; must be tied directly to VDD to enable the regulator or to ground to disable it. |
| 19 | AVDD | power_in | Positive supply for analog modules; must always be connected, regardless of whether analog modules are used. |
| 20 | AVSS | power_in | Ground reference for analog modules; must always be connected, regardless of whether analog modules are used. |
| 21 | RA3/AN3/VREF+ | bidirectional | Digital I/O with TTL input; also analog input channel 3 and A/D high reference voltage input VREF+. |
| 22 | RA2/AN2/VREF- | bidirectional | Digital I/O with TTL input; also analog input channel 2 (comparator C2+ input) and A/D and comparator low reference voltage input VREF-. |
| 23 | RA1/LEDB/AN1 | bidirectional | Digital I/O with TTL input; also Ethernet LEDB indicator output, which can directly drive an LED, and analog input channel 1. |
| 24 | RA0/LEDA/AN0 | bidirectional | Digital I/O with TTL input; also Ethernet LEDA indicator output, which can directly drive an LED, and analog input channel 0. |
| 25 | VSS | power_in | Ground reference for logic and I/O pins. |
| 26 | VDD | power_in | Positive supply for peripheral digital logic and I/O pins. |
| 27 | RA5/AN4 | bidirectional | Digital I/O with TTL input; also analog input channel 4. |
| 28 | RA4/T0CKI | bidirectional | Digital I/O with Schmitt Trigger input; also Timer0 external clock input T0CKI. |
| 29 | RC1/T1OSI/ECCP2/P2A | bidirectional | Digital I/O with Schmitt Trigger input; also Timer1 oscillator input T1OSI and ECCP2 capture/compare/PWM pin with Enhanced PWM output A (P2A). |
| 30 | RC0/T1OSO/T13CKI | bidirectional | Digital I/O with Schmitt Trigger input; also Timer1 oscillator output T1OSO and Timer1/Timer3 external clock input T13CKI. |
| 31 | RC6/TX1/CK1 | bidirectional | Digital I/O with Schmitt Trigger input; also EUSART1 asynchronous transmit TX1 or synchronous clock CK1. |
| 32 | RC7/RX1/DT1 | bidirectional | Digital I/O with Schmitt Trigger input; also EUSART1 asynchronous receive RX1 or synchronous data DT1. |
| 33 | RC2/ECCP1/P1A | bidirectional | Digital I/O with Schmitt Trigger input; also ECCP1 capture/compare/PWM pin with Enhanced PWM output A (P1A). |
| 34 | RC3/SCK1/SCL1 | bidirectional | Digital I/O with Schmitt Trigger input; also MSSP1 SPI clock (SCK1) or I2C clock (SCL1). |
| 35 | RC4/SDI1/SDA1 | bidirectional | Digital I/O with Schmitt Trigger input; also MSSP1 SPI data input (SDI1) or I2C data (SDA1). |
| 36 | RC5/SDO1 | bidirectional | Digital I/O with Schmitt Trigger input; also MSSP1 SPI data output (SDO1). |
| 37 | RB7/KBI3/PGD | bidirectional | Digital I/O with TTL input and weak pull-up when RBPU is cleared; also interrupt-on-change input KBI3 and ICSP/ICD serial data pin PGD. |
| 38 | VDD | power_in | Positive supply for peripheral digital logic and I/O pins. |
| 39 | OSC1/CLKI | input | Oscillator crystal or external clock source input; Schmitt Trigger buffer in internal RC mode and CMOS otherwise. |
| 40 | OSC2/CLKO | output | Oscillator crystal output connecting to a crystal or resonator; in internal RC mode outputs CLKO at 1/4 the OSC1 frequency. |
| 41 | VSS | power_in | Ground reference for logic and I/O pins. |
| 42 | RB6/KBI2/PGC | bidirectional | Digital I/O with TTL input and weak pull-up when RBPU is cleared; also interrupt-on-change input KBI2 and ICSP/ICD clock pin PGC. |
| 43 | RB5/KBI1 | bidirectional | Digital I/O with TTL input and weak pull-up when RBPU is cleared; also interrupt-on-change input KBI1. |
| 44 | RB4/KBI0 | bidirectional | Digital I/O with TTL input and weak pull-up when RBPU is cleared; also interrupt-on-change input KBI0. |
| 45 | VSSRX | power_in | Ground reference for the Ethernet PHY receive subsystem. |
| 46 | TPIN- | input | Analog Ethernet differential signal input (negative). |
| 47 | TPIN+ | input | Analog Ethernet differential signal input (positive). |
| 48 | VDDRX | power_in | Positive 3.3V supply for the Ethernet PHY receive subsystem. |
| 49 | VDDTX | power_in | Positive 3.3V supply for the Ethernet PHY transmit subsystem. |
| 50 | TPOUT- | output | Ethernet differential signal output (negative). |
| 51 | TPOUT+ | output | Ethernet differential signal output (positive). |
| 52 | VSSTX | power_in | Ground reference for the Ethernet PHY transmit subsystem. |
| 53 | RBIAS | input | Analog bias current input for the Ethernet PHY; must be tied to VSS via a resistor (see Section 19.0 for the specification). |
| 54 | VDDPLL | power_in | Positive 3.3V supply for the Ethernet PHY PLL. |
| 55 | VSSPLL | power_in | Ground reference for the Ethernet PHY PLL. |
| 56 | VSS | power_in | Ground reference for logic and I/O pins. |
| 57 | VDD | power_in | Positive supply for peripheral digital logic and I/O pins. |
| 58 | RD2/CCP4/P3D | bidirectional | Digital I/O with Schmitt Trigger input; also CCP4 capture/compare/PWM pin and ECCP3 Enhanced PWM output D (P3D). |
| 59 | RD1/ECCP3/P3A | bidirectional | Digital I/O with Schmitt Trigger input; also ECCP3 capture/compare/PWM pin with Enhanced PWM output A (P3A). |
| 60 | RD0/P1B | bidirectional | Digital I/O with Schmitt Trigger input and weak pull-up enabled by RDPU; also ECCP1 Enhanced PWM output B (P1B). |
| 61 | RE5/P1C | bidirectional | Digital I/O with Schmitt Trigger input and weak pull-up enabled by REPU; also ECCP1 Enhanced PWM output C (P1C). |
| 62 | RE4/P3B | bidirectional | Digital I/O with Schmitt Trigger input and weak pull-up enabled by REPU; also ECCP3 Enhanced PWM output B (P3B). |
| 63 | RE3/P3C | bidirectional | Digital I/O with Schmitt Trigger input and weak pull-up enabled by REPU; also ECCP3 Enhanced PWM output C (P3C). |
| 64 | RE2/P2B | bidirectional | Digital I/O with Schmitt Trigger input and weak pull-up enabled by REPU; also ECCP2 Enhanced PWM output B (P2B). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating voltage range | 2.35 | 3.6 | V | 3 | |||
| Operating voltage range using Ethernet module | 3.1 | 3.6 | V | using Ethernet module | 3 | ||
| Operating frequency | 41.667 | MHz | 13 | ||||
| High-current sink current | 25 | mA | PORTB and PORTC | 3 | |||
| High-current source current | 25 | mA | PORTB and PORTC | 3 | |||
| Digital-only input tolerated voltage | 5.5 | V | Digital-only input pins (Table 11-2) | 146 | |||
| Program Flash erase/write endurance | 100 | erase/write cycles | 11 | ||||
| Program Flash data retention | 20 | years | 11 | ||||
| Ethernet clock source frequency | 25 | MHz | Ethernet applications | 51 | |||
| VCAP/VDDCORE stabilization capacitor | 10 | µF | Regulator enabled; connected to ground; ESR < 5 Ω | 45 |
CAD (KiCad official)
- Symbol:
PIC18F67J60-I - Footprint:
Package_QFP:TQFP-64_10x10mm_P0.5mm - 3D model: TQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
pic18f67j60-i-etched.step/pic18f67j60-i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pic18f67j60-i.step/pic18f67j60-i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (492 pp, sha256
a5190601007a9ae0, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).