3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownPIC18F6310-I
Microchip Tech · Microcontroller Units (MCUs/MPUs/SOCs) · TQFP-64(10x10)
PIC18F6310-I from Microchip Tech, in a TQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RE1/WR | bidirectional | Digital I/O (PORTE bit 1) with Schmitt Trigger input; serves as the Parallel Slave Port write enable control input (WR, TTL). |
| 2 | RE0/RD | bidirectional | Digital I/O (PORTE bit 0) with Schmitt Trigger input; serves as the Parallel Slave Port read enable control input (RD, TTL). |
| 3 | RG0/CCP3 | bidirectional | Digital I/O (PORTG bit 0) with Schmitt Trigger input; alternately Capture 3 input / Compare 3 output / PWM3 output. |
| 4 | RG1/TX2/CK2 | bidirectional | Digital I/O (PORTG bit 1) with Schmitt Trigger input; alternately AUSART2 asynchronous transmit (TX2) or synchronous clock (CK2). |
| 5 | RG2/RX2/DT2 | bidirectional | Digital I/O (PORTG bit 2) with Schmitt Trigger input; alternately AUSART2 asynchronous receive (RX2) or synchronous data (DT2). |
| 6 | RG3 | bidirectional | Digital I/O (PORTG bit 3) with Schmitt Trigger input buffer. |
| 7 | RG5/MCLR/VPP | input | Input-only pin: active-low Master Clear (Reset) input when MCLRE is set, otherwise digital input RG5; also the programming voltage input (VPP). |
| 8 | RG4 | bidirectional | Digital I/O (PORTG bit 4) with Schmitt Trigger input buffer. |
| 9 | VSS | power_in | Ground reference for logic and I/O pins. |
| 10 | VDD | power_in | Positive supply for logic and I/O pins. |
| 11 | RF7/SS | bidirectional | Digital I/O (PORTF bit 7) with Schmitt Trigger input; SPI slave select input (SS) for the MSSP module (TTL). |
| 12 | RF6/AN11 | bidirectional | Digital I/O (PORTF bit 6); Analog Input 11 and Comparator C1- input. |
| 13 | RF5/AN10/CVREF | bidirectional | Digital I/O (PORTF bit 5); Analog Input 10 and Comparator C1+ input; comparator voltage reference output CVREF, which disables digital I/O when enabled. |
| 14 | RF4/AN9 | bidirectional | Digital I/O (PORTF bit 4); Analog Input 9 and Comparator C2- input. |
| 15 | RF3/AN8 | bidirectional | Digital I/O (PORTF bit 3); Analog Input 8 and Comparator C2+ input. |
| 16 | RF2/AN7/C1OUT | bidirectional | Digital I/O (PORTF bit 2); Analog Input 7; Comparator 1 output (C1OUT), which takes priority over port data. |
| 17 | RF1/AN6/C2OUT | bidirectional | Digital I/O (PORTF bit 1); Analog Input 6; Comparator 2 output (C2OUT), which takes priority over port data. |
| 18 | RF0/AN5 | bidirectional | Digital I/O (PORTF bit 0) with Schmitt Trigger input; Analog Input 5. |
| 19 | AVDD | power_in | Positive supply for analog modules; must always be connected regardless of whether the analog modules are used. |
| 20 | AVSS | power_in | Ground reference for analog modules; must always be connected regardless of whether the analog modules are used. |
| 21 | RA3/AN3/VREF+ | bidirectional | Digital I/O (PORTA bit 3); Analog Input 3; A/D reference voltage (high) input. |
| 22 | RA2/AN2/VREF- | bidirectional | Digital I/O (PORTA bit 2); Analog Input 2; A/D reference voltage (low) input. |
| 23 | RA1/AN1 | bidirectional | Digital I/O (PORTA bit 1); Analog Input 1. |
| 24 | RA0/AN0 | bidirectional | Digital I/O (PORTA bit 0); Analog Input 0. |
| 25 | VSS | power_in | Ground reference for logic and I/O pins. |
| 26 | VDD | power_in | Positive supply for logic and I/O pins. |
| 27 | RA5/AN4/HLVDIN | bidirectional | Digital I/O (PORTA bit 5); Analog Input 4; High/Low-Voltage Detect external trip point input (HLVDIN). |
| 28 | RA4/T0CKI | bidirectional | Digital I/O (PORTA bit 4) with Schmitt Trigger input and open-drain output; Timer0 external clock input (T0CKI). |
| 29 | RC1/T1OSI/CCP2 | bidirectional | Digital I/O (PORTC bit 1) with Schmitt Trigger input; Timer1 oscillator input (T1OSI); CCP2 capture input / compare / PWM output (default CCP2 assignment when CCP2MX is set). |
| 30 | RC0/T1OSO/T13CKI | bidirectional | Digital I/O (PORTC bit 0) with Schmitt Trigger input; Timer1 oscillator output (T1OSO); Timer1/Timer3 external clock input (T13CKI). |
| 31 | RC6/TX1/CK1 | bidirectional | Digital I/O (PORTC bit 6) with Schmitt Trigger input; EUSART1 asynchronous transmit (TX1) or synchronous clock (CK1). |
| 32 | RC7/RX1/DT1 | bidirectional | Digital I/O (PORTC bit 7) with Schmitt Trigger input; EUSART1 asynchronous receive (RX1) or synchronous data (DT1). |
| 33 | RC2/CCP1 | bidirectional | Digital I/O (PORTC bit 2) with Schmitt Trigger input; Capture 1 input / Compare 1 output / PWM1 output. |
| 34 | RC3/SCK/SCL | bidirectional | Digital I/O (PORTC bit 3) with Schmitt Trigger input; MSSP SPI clock input/output (SCK) or I2C clock (SCL). |
| 35 | RC4/SDI/SDA | bidirectional | Digital I/O (PORTC bit 4) with Schmitt Trigger input; MSSP SPI data input (SDI) or I2C data I/O (SDA). |
| 36 | RC5/SDO | bidirectional | Digital I/O (PORTC bit 5) with Schmitt Trigger input; MSSP SPI data output (SDO). |
| 37 | RB7/KBI3/PGD | bidirectional | Digital I/O (PORTB bit 7) with weak pull-up when RBPU is cleared; interrupt-on-change pin KBI3; ICSP/ICD serial data pin PGD. |
| 38 | VDD | power_in | Positive supply for logic and I/O pins. |
| 39 | OSC1/CLKI/RA7 | input | Oscillator crystal or external clock input (OSC1/CLKI) with ST buffer in RC mode and CMOS otherwise; when not used as oscillator input, general-purpose I/O RA7. |
| 40 | OSC2/CLKO/RA6 | output | Oscillator crystal output (OSC2) connecting to the crystal/resonator, or CLKO (FOSC/4) in RC mode; when not used as oscillator, general-purpose I/O RA6. |
| 41 | VSS | power_in | Ground reference for logic and I/O pins. |
| 42 | RB6/KBI2/PGC | bidirectional | Digital I/O (PORTB bit 6) with Schmitt Trigger input and weak pull-up when RBPU is cleared; interrupt-on-change pin KBI2; ICSP/ICD programming clock PGC. |
| 43 | RB5/KBI1 | bidirectional | Digital I/O (PORTB bit 5) with weak pull-up when RBPU is cleared; interrupt-on-change pin KBI1. |
| 44 | RB4/KBI0 | bidirectional | Digital I/O (PORTB bit 4) with weak pull-up when RBPU is cleared; interrupt-on-change pin KBI0. |
| 45 | RB3/INT3 | bidirectional | Digital I/O (PORTB bit 3) with weak pull-up when RBPU is cleared; External Interrupt 3 (INT3). |
| 46 | RB2/INT2 | bidirectional | Digital I/O (PORTB bit 2) with weak pull-up when RBPU is cleared; External Interrupt 2 (INT2) with Schmitt Trigger input. |
| 47 | RB1/INT1 | bidirectional | Digital I/O (PORTB bit 1) with weak pull-up when RBPU is cleared; External Interrupt 1 (INT1) with Schmitt Trigger input. |
| 48 | RB0/INT0 | bidirectional | Digital I/O (PORTB bit 0) with weak pull-up when RBPU is cleared; External Interrupt 0 (INT0) with Schmitt Trigger input. |
| 49 | RD7/PSP7 | bidirectional | Digital I/O (PORTD bit 7) with Schmitt Trigger input; Parallel Slave Port data bit 7 (TTL). |
| 50 | RD6/PSP6 | bidirectional | Digital I/O (PORTD bit 6) with Schmitt Trigger input; Parallel Slave Port data bit 6 (TTL). |
| 51 | RD5/PSP5 | bidirectional | Digital I/O (PORTD bit 5) with Schmitt Trigger input; Parallel Slave Port data bit 5 (TTL). |
| 52 | RD4/PSP4 | bidirectional | Digital I/O (PORTD bit 4) with Schmitt Trigger input; Parallel Slave Port data bit 4 (TTL). |
| 53 | RD3/PSP3 | bidirectional | Digital I/O (PORTD bit 3) with Schmitt Trigger input; Parallel Slave Port data bit 3 (TTL). |
| 54 | RD2/PSP2 | bidirectional | Digital I/O (PORTD bit 2) with Schmitt Trigger input; Parallel Slave Port data bit 2 (TTL). |
| 55 | RD1/PSP1 | bidirectional | Digital I/O (PORTD bit 1) with Schmitt Trigger input; Parallel Slave Port data bit 1 (TTL). |
| 56 | VSS | power_in | Ground reference for logic and I/O pins. |
| 57 | VDD | power_in | Positive supply for logic and I/O pins. |
| 58 | RD0/PSP0 | bidirectional | Digital I/O (PORTD bit 0) with Schmitt Trigger input; Parallel Slave Port data bit 0 (TTL). |
| 59 | RE7/CCP2 | bidirectional | Digital I/O (PORTE bit 7) with Schmitt Trigger input; alternate CCP2 capture input / compare / PWM output when CCP2MX is cleared in Microcontroller mode. |
| 60 | RE6 | bidirectional | Digital I/O (PORTE bit 6) with Schmitt Trigger input buffer. |
| 61 | RE5 | bidirectional | Digital I/O (PORTE bit 5) with Schmitt Trigger input buffer. |
| 62 | RE4 | bidirectional | Digital I/O (PORTE bit 4) with Schmitt Trigger input buffer. |
| 63 | RE3 | bidirectional | Digital I/O (PORTE bit 3) with Schmitt Trigger input buffer. |
| 64 | RE2/CS | bidirectional | Digital I/O (PORTE bit 2) with Schmitt Trigger input; Parallel Slave Port chip select control input (CS, TTL). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TQFP-64(10x10) |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 64 |
CAD (KiCad official)
- Symbol:
PIC18F6310-I - Footprint:
Package_QFP:TQFP-64_10x10mm_P0.5mm - 3D model: TQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
pic18f6310-i-etched.step/pic18f6310-i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pic18f6310-i.step/pic18f6310-i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (412 pp, sha256
d256661b81c1a706, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).