Generated by kicad-footprint-generator · KiCad file format 20260206
PIC16LC72A-04I
Microchip Tech · Microcontroller Units (MCUs/MPUs/SOCs) · SOIC-28-300mil
PIC16LC72A-04I from Microchip Tech, in a SOIC-28-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MCLR/VPP | input | Active-low master clear (reset) input to the device, or the programming voltage input. |
| 2 | RA0/AN0 | bidirectional | PORTA bidirectional TTL I/O pin that can also be analog input 0. |
| 3 | RA1/AN1 | bidirectional | PORTA bidirectional TTL I/O pin that can also be analog input 1. |
| 4 | RA2/AN2 | bidirectional | PORTA bidirectional TTL I/O pin that can also be analog input 2. |
| 5 | RA3/AN3/VREF | bidirectional | PORTA bidirectional TTL I/O pin that can also be analog input 3 or the analog reference voltage. |
| 6 | RA4/T0CKI | bidirectional | PORTA Schmitt-trigger I/O pin that can also be the clock input to the Timer0 module, and whose output is open drain. |
| 7 | RA5/SS/AN4 | bidirectional | PORTA bidirectional TTL I/O pin that can also be analog input 4 or the slave select for the synchronous serial port. |
| 8 | VSS | power_in | Ground reference for logic and I/O pins. |
| 9 | OSC1/CLKIN | input | Oscillator crystal input or external clock source input; Schmitt trigger input in RC oscillator mode and CMOS input otherwise. |
| 10 | OSC2/CLKOUT | output | Oscillator crystal output connecting to a crystal or resonator in crystal mode; in RC mode it outputs CLKOUT at 1/4 the OSC1 frequency, denoting the instruction cycle rate. |
| 11 | RC0/T1OSO/T1CKI | bidirectional | PORTC Schmitt-trigger I/O pin that can also be the Timer1 oscillator output or the Timer1 clock input. |
| 12 | RC1/T1OSI | bidirectional | PORTC Schmitt-trigger I/O pin that can also be the Timer1 oscillator input. |
| 13 | RC2/CCP1 | bidirectional | PORTC Schmitt-trigger I/O pin that can also be the Capture1 input, Compare1 output, or PWM1 output. |
| 14 | RC3/SCK/SCL | bidirectional | PORTC Schmitt-trigger I/O pin that is the synchronous serial clock input/output for both SPI and I2C modes. |
| 15 | RC4/SDI/SDA | bidirectional | PORTC Schmitt-trigger I/O pin that is the SPI data input (SPI mode) or the data I/O (I2C mode). |
| 16 | RC5/SDO | bidirectional | PORTC Schmitt-trigger I/O pin that is the SPI data output (SPI mode) or the synchronous serial port data output. |
| 17 | RC6 | bidirectional | PORTC Schmitt-trigger bidirectional I/O port pin. |
| 18 | RC7 | bidirectional | PORTC Schmitt-trigger bidirectional I/O port pin. |
| 19 | VSS | power_in | Ground reference for logic and I/O pins. |
| 20 | VDD | power_in | Positive supply for logic and I/O pins. |
| 21 | RB0/INT | bidirectional | PORTB bidirectional I/O pin with weak pull-up option that can also be the external interrupt pin, using a Schmitt-trigger buffer when configured as the interrupt. |
| 22 | RB1 | bidirectional | PORTB bidirectional TTL I/O pin with programmable internal weak pull-up. |
| 23 | RB2 | bidirectional | PORTB bidirectional TTL I/O pin with programmable internal weak pull-up. |
| 24 | RB3 | bidirectional | PORTB bidirectional TTL I/O pin with programmable internal weak pull-up. |
| 25 | RB4 | bidirectional | PORTB bidirectional TTL I/O pin with programmable internal weak pull-up that provides the interrupt-on-change function. |
| 26 | RB5 | bidirectional | PORTB bidirectional TTL I/O pin with programmable internal weak pull-up that provides the interrupt-on-change function. |
| 27 | RB6 | bidirectional | PORTB bidirectional I/O pin with programmable internal weak pull-up providing interrupt-on-change and serving as the serial programming clock, with a Schmitt-trigger input in programming mode. |
| 28 | RB7 | bidirectional | PORTB bidirectional I/O pin with programmable internal weak pull-up providing interrupt-on-change and serving as the serial programming data, with a Schmitt-trigger input in programming mode. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-28-300mil |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 28 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Ambient temperature under bias | -55 | 125 | °C | 81 | |||
| Storage temperature | -65 | 150 | °C | 81 | |||
| Voltage on any pin with respect to VSS (except VDD, MCLR, and RA4) | -0.3 | V | 81 | ||||
| Voltage on VDD with respect to VSS | -0.3 | 7.5 | V | 81 | |||
| Voltage on MCLR with respect to VSS (Note 2) | 0 | 13.25 | V | 81 | |||
| Voltage on RA4 with respect to VSS | 0 | 8.5 | V | 81 | |||
| Total power dissipation (Note 1) | 1 | W | 81 | ||||
| Input clamp current | IIK | 20 | mA | VI < 0 or VI > VDD | 81 | ||
| Output clamp current | IOK | 20 | mA | VO < 0 or VO > VDD | 81 | ||
| Operating temperature (industrial) | TA | -40 | 85 | °C | -40°C TA +85°C for industrial | 85 | |
| VDD Supply Voltage | VDD | 2.5 | 5.5 | V | LP, XT, RC osc modes (DC - 4 MHz) | 85 | |
| VDD Supply Voltage, BOR enabled | VBOR | 5.5 | V | BOR enabled (Note 7) | 85 | ||
| VDD Rise Rate to ensure internal Power-on Reset signal | SVDD | 0.05 | V/ms | PWRT enabled (PWRTE bit clear) | 85 | ||
| Brown-out Reset voltage trip point | VBOR | 3.65 | 4.35 | V | BODEN bit set | 85 | |
| Supply Current (XT, RC osc modes) | IDD | 2 | 3.8 | mA | XT, RC osc modes; FOSC = 4 MHz, VDD = 3.0V (Note 4) | 85 | |
| Supply Current (LP osc mode) | IDD | 22.5 | 48 | µA | LP OSC MODE; FOSC = 32 kHz, VDD = 3.0V, WDT disabled | 85 | |
| Power-down Current | IPD | 7.5 | 30 | µA | VDD = 3.0V, WDT enabled, -40C to +85C | 85 | |
| Power-down Current | IPD | 0.9 | 5 | µA | VDD = 3.0V, WDT disabled, 0C to +70C | 85 | |
| Module Differential Current, Watchdog Timer | IWDT | 6 | 20 | µA | WDTE BIT SET, VDD = 4.0V | 85 | |
| Module Differential Current, Brown-out Reset | IBOR | 200 | µA | BODEN bit set, VDD = 5.0V | 85 | ||
| Input Low Voltage, I/O ports with TTL buffer | VIL | 0.8 | V | 4.5V ≤ VDD ≤ 5.5V | 86 | ||
| Input High Voltage, I/O ports with TTL buffer | VIH | 2 | V | 4.5V ≤ VDD ≤ 5.5V | 86 | ||
| Input Leakage Current, I/O ports | IIL | 1 | µA | Vss ≤ VPIN ≤ VDD, Pin at hi-impedance | 86 | ||
| Input Leakage Current, MCLR, RA4/T0CKI | IIL | 5 | µA | Vss ≤ VPIN ≤ VDD | 86 | ||
| Input Leakage Current, OSC1 | IIL | 5 | µA | Vss ≤ VPIN ≤ VDD, XT, HS and LP osc modes | 86 | ||
| PORTB weak pull-up current | IPURB | 50 | 250 | 400 | µA | VDD = 5V, VPIN = VSS | 86 |
| Output Low Voltage, I/O ports | VOL | 0.6 | V | IOL = 8.5 mA, VDD = 4.5V, -40C to +85C | 86 | ||
| Output Low Voltage, OSC2/CLKOUT (RC osc mode) | VOL | 0.6 | V | IOL = 1.6 mA, VDD = 4.5V, -40C to +85C | 87 | ||
| Open-Drain High Voltage | VOD | 8.5 | V | RA4 pin | 87 | ||
| OSC2 pin capacitive loading | COSC2 | 15 | pF | In XT, HS and LP modes when external clock is used to drive OSC1. | 87 | ||
| Capacitive loading, All I/O pins and OSC2 (in RC mode) | CIO | 50 | pF | 87 | |||
| Capacitive loading, SCL, SDA in I2C mode | Cb | 400 | pF | 87 | |||
| Oscillator Frequency (XT osc mode) | Fosc | 0.1 | 4 | MHz | XT osc mode | 90 | |
| Oscillator Frequency (LP osc mode) | Fosc | 5 | 200 | kHz | LP osc mode | 90 | |
| Oscillator Frequency (RC osc mode) | Fosc | 4 | MHz | RC osc mode | 90 | ||
| External CLKIN Frequency (HS osc mode -04) | Fosc | 4 | MHz | HS osc mode (-04) | 90 | ||
| Oscillator Period (XT osc mode) | Tosc | 250 | 10000 | ns | XT osc mode | 90 | |
| Oscillator Period (LP osc mode) | Tosc | 5 | µs | LP osc mode | 90 | ||
| Instruction Cycle Time | TCY | 200 | ns | TCY = 4/FOSC | 90 | ||
| External Clock in (OSC1) High or Low Time (XT oscillator) | TosL, TosH | 100 | ns | XT oscillator | 90 | ||
| External Clock in (OSC1) Rise or Fall Time (XT oscillator) | TosR, TosF | 25 | ns | XT oscillator | 90 | ||
| CLKOUT rise time | TckR | 35 | 100 | ns | Note 1 | 91 | |
| CLKOUT fall time | TckF | 35 | 100 | ns | Note 1 | 91 | |
| OSC1 (Q1 cycle) to Port out valid | TosH2ioV | 50 | 150 | ns | 91 | ||
| OSC1 (Q2 cycle) to Port input invalid (I/O in hold time), PIC16LCXX | TosH2ioI | 200 | ns | 91 | |||
| Port output rise time, PIC16LCXX | TioR | 80 | ns | 91 | |||
| Port output fall time, PIC16LCXX | TioF | 80 | ns | 91 | |||
| Reference voltage | VREF | 2.5 | V | 101 | |||
| Recommended impedance of analog voltage source | ZAIN | 10 | kΩ | 101 | |||
| A/D clock period, PIC16LCXX (TOSC based) | TAD | 2 | µs | TOSC based, VREF full range | 102 | ||
| A/D clock period, PIC16LCXX (A/D RC mode) | TAD | 3 | 6 | 9 | µs | A/D RC Mode | 102 |
CAD (KiCad official)
- Symbol:
PIC16LC72A-04I - Footprint:
Package_SO:SOIC-28W_7.5x17.9mm_P1.27mm - 3D model: SOIC-28-300mil (KiCad packages3D, STEP)
- 3D model files:
pic16lc72a-04i-etched.step/pic16lc72a-04i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pic16lc72a-04i.step/pic16lc72a-04i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (122 pp, sha256
001eda69b9433079, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).