Generated by kicad-footprint-generator · KiCad file format 20260206
PIC16C774-I
Microchip Tech · Microcontroller Units (MCUs/MPUs/SOCs) · DIP-40-600mil
PIC16C774-I from Microchip Tech, in a DIP-40-600mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MCLR/VPP | input | Master clear (reset) input or programming voltage input; this pin is an active low reset to the device. |
| 2 | RA0/AN0 | bidirectional | PORTA bidirectional I/O (TTL input); can also be analog input 0. |
| 3 | RA1/AN1 | bidirectional | PORTA bidirectional I/O (TTL input); can also be analog input 1. |
| 4 | RA2/AN2/VREF-/VRL | bidirectional | PORTA bidirectional I/O (TTL input); can also be analog input 2, negative analog reference voltage input, or internal voltage reference low. |
| 5 | RA3/AN3/VREF+/VRH | bidirectional | PORTA bidirectional I/O (TTL input); can also be analog input 3, positive analog reference voltage input, or internal voltage reference high. |
| 6 | RA4/T0CKI | bidirectional | PORTA bidirectional I/O (Schmitt Trigger input); can also be the clock input to the Timer0 timer/counter, and its output is open drain type. |
| 7 | RA5/AN4 | bidirectional | PORTA bidirectional I/O (TTL input); can also be analog input 4. |
| 8 | RE0/RD/AN5 | bidirectional | PORTE bidirectional I/O (ST/TTL input); can also be read control for the parallel slave port, or analog input 5. |
| 9 | RE1/WR/AN6 | bidirectional | PORTE bidirectional I/O (ST/TTL input); can also be write control for the parallel slave port, or analog input 6. |
| 10 | RE2/CS/AN7 | bidirectional | PORTE bidirectional I/O (ST/TTL input); can also be select control for the parallel slave port, or analog input 7. |
| 11 | AVDD | power_in | Positive supply for the A/D converter. |
| 12 | AVSS | power_in | Ground reference for the A/D converter. |
| 13 | OSC1/CLKIN | input | Oscillator crystal input or external clock source input. |
| 14 | OSC2/CLKOUT | output | Oscillator crystal output connecting to a crystal or resonator in crystal mode; in RC mode it outputs CLKOUT at 1/4 the OSC1 frequency, denoting the instruction cycle rate. |
| 15 | RC0/T1OSO/T1CKI | bidirectional | PORTC bidirectional I/O (Schmitt Trigger input); can also be the Timer1 oscillator output or a Timer1 clock input. |
| 16 | RC1/T1OSI/CCP2 | bidirectional | PORTC bidirectional I/O (Schmitt Trigger input); can also be the Timer1 oscillator input or Capture2 input/Compare2 output/PWM2 output. |
| 17 | RC2/CCP1 | bidirectional | PORTC bidirectional I/O (Schmitt Trigger input); can also be the Capture1 input/Compare1 output/PWM1 output. |
| 18 | RC3/SCK/SCL | bidirectional | PORTC bidirectional I/O (Schmitt Trigger input); can also be the synchronous serial clock input/output for both SPI and I2C modes. |
| 19 | RD0/PSP0 | bidirectional | PORTD bidirectional I/O or parallel slave port data bit 0 when interfacing to a microprocessor bus (ST/TTL input). |
| 20 | RD1/PSP1 | bidirectional | PORTD bidirectional I/O or parallel slave port data bit 1 when interfacing to a microprocessor bus (ST/TTL input). |
| 21 | RD2/PSP2 | bidirectional | PORTD bidirectional I/O or parallel slave port data bit 2 when interfacing to a microprocessor bus (ST/TTL input). |
| 22 | RD3/PSP3 | bidirectional | PORTD bidirectional I/O or parallel slave port data bit 3 when interfacing to a microprocessor bus (ST/TTL input). |
| 23 | RC4/SDI/SDA | bidirectional | PORTC bidirectional I/O (Schmitt Trigger input); can also be the SPI Data In (SPI mode) or data I/O (I2C mode). |
| 24 | RC5/SDO | bidirectional | PORTC bidirectional I/O (Schmitt Trigger input); can also be the SPI Data Out (SPI mode). |
| 25 | RC6/TX/CK | bidirectional | PORTC bidirectional I/O (Schmitt Trigger input); can also be the USART asynchronous transmit or synchronous clock. |
| 26 | RC7/RX/DT | bidirectional | PORTC bidirectional I/O (Schmitt Trigger input); can also be the USART asynchronous receive or synchronous data. |
| 27 | RD4/PSP4 | bidirectional | PORTD bidirectional I/O or parallel slave port data bit 4 when interfacing to a microprocessor bus (ST/TTL input). |
| 28 | RD5/PSP5 | bidirectional | PORTD bidirectional I/O or parallel slave port data bit 5 when interfacing to a microprocessor bus (ST/TTL input). |
| 29 | RD6/PSP6 | bidirectional | PORTD bidirectional I/O or parallel slave port data bit 6 when interfacing to a microprocessor bus (ST/TTL input). |
| 30 | RD7/PSP7 | bidirectional | PORTD bidirectional I/O or parallel slave port data bit 7 when interfacing to a microprocessor bus (ST/TTL input). |
| 31 | VSS | power_in | Ground reference for logic and I/O pins. |
| 32 | VDD | power_in | Positive supply for logic and I/O pins. |
| 33 | RB0/INT | bidirectional | PORTB bidirectional I/O (Schmitt Trigger input when multiplexed); can also be the external interrupt pin. |
| 34 | RB1/SS | bidirectional | PORTB bidirectional I/O (Schmitt Trigger input when multiplexed); can also be the SSP slave select. |
| 35 | RB2/AN8 | bidirectional | PORTB bidirectional I/O (TTL input); can also be analog input 8. |
| 36 | RB3/AN9/LVDIN | bidirectional | PORTB bidirectional I/O (TTL input); can also be analog input 9 or the input reference for low voltage detect. |
| 37 | RB4 | bidirectional | PORTB bidirectional I/O (TTL input) with interrupt-on-change function. |
| 38 | RB5 | bidirectional | PORTB bidirectional I/O (TTL input) with interrupt-on-change function. |
| 39 | RB6 | bidirectional | PORTB bidirectional I/O (TTL/Schmitt Trigger input in serial programming mode) with interrupt-on-change function; serves as the serial programming clock. |
| 40 | RB7 | bidirectional | PORTB bidirectional I/O (TTL/Schmitt Trigger input in serial programming mode) with interrupt-on-change function; serves as the serial programming data. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | DIP-40-600mil |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 40 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating temperature (industrial -I range) | TA | -40 | 85 | °C | Industrial; commercial range is 0°C ≤ TA ≤ +70°C | 152 | |
| Supply Voltage | VDD | 4 | 5.5 | V | XT, RC and LP osc configuration | 152 | |
| Supply Voltage | VDD | 4.5 | 5.5 | V | HS osc configuration | 152 | |
| VDD rise rate to ensure internal Power-on Reset signal | SVDD | 0.05 | V/ms | See section on Power-on Reset for details. PWRT enabled | 152 | ||
| Supply Current (IDD) | IDD | 2.7 | 5 | mA | XT, RC osc configuration FOSC = 4 MHz, VDD = 5.5V | 152 | |
| Supply Current (IDD) | IDD | 13.5 | 30 | mA | HS osc configuration FOSC = 20 MHz, VDD = 5.5V | 152 | |
| Power-down Current (IPD) | IPD | 1.5 | 16 | µA | VDD = 4.0V, -0°C to +70°C | 152 | |
| Power-down Current (IPD) | IPD | 1.5 | 19 | µA | VDD = 4.0V, -40°C to +85°C | 152 | |
| Watchdog Timer module differential current | ∆IWDT | 6 | 20 | µA | VDD = 4.0V | 152 | |
| Brown-out Reset module differential current | ∆IBOR | 200 | µA | 152 | |||
| Input Low Voltage, I/O ports with TTL buffer | VIL | 0.8 | V | 4.5V ≤ VDD ≤ 5.5V | 154 | ||
| Input High Voltage, I/O ports with TTL buffer | VIH | 2 | V | 4.5V ≤ VDD ≤ 5.5V | 154 | ||
| PORTB weak pull-up current | IPURB | 50 | 250 | 400 | µA | VDD = 5V, VPIN = VSS | 154 |
| Input leakage current, I/O ports (digital) | IIL | -1 | 1 | µA | Vss ≤ VPIN ≤ VDD, Pin at hi-impedance | 154 | |
| Input leakage current, I/O ports (RA0-RA3, RA5, RB2, RB3 analog) | IIL | -100 | 100 | nA | Vss ≤ VPIN ≤ VDD, Pin at hi-impedance | 154 | |
| Input leakage current, MCLR and RA4/T0CKI | -5 | 5 | µA | Vss ≤ VPIN ≤ VDD | 154 | ||
| Output Low Voltage, I/O ports | VOL | 0.6 | V | IOL = 8.5 mA, VDD = 4.5V, -40°C to +85°C | 154 | ||
| Open-Drain High Voltage, RA4 pin | VOD | 8.5 | V | RA4 pin | 155 | ||
| Capacitive loading, all I/O pins and OSC2 (RC mode) | CIO | 50 | pF | 155 | |||
| VREF output voltage VRL | VRL | 2 | 2.048 | 2.1 | V | VDD ≥ 2.5V | 156 |
| VREF output voltage VRH | VRH | 4 | 4.096 | 4.2 | V | VDD ≥ 4.5V | 156 |
| VREF output voltage drift temperature coefficient | TCVOUT | 15 | 50 | ppm/°C | Note 1 | 156 | |
| VREF line regulation | ∆VOUT/∆VDD | 50 | µV/V | 156 | |||
| LVD Voltage | LVV | 2.5 | 2.58 | 2.66 | V | LVV = 0100 | 157 |
| LVD Voltage | LVV | 2.7 | 2.78 | 2.86 | V | LVV = 0101 | 157 |
| LVD Voltage | LVV | 2.8 | 2.89 | 2.98 | V | LVV = 0110 | 157 |
| LVD Voltage | LVV | 3 | 3.1 | 3.2 | V | LVV = 0111 | 157 |
| LVD Voltage | LVV | 3.3 | 3.41 | 3.52 | V | LVV = 1000 | 157 |
| LVD Voltage | LVV | 3.5 | 3.61 | 3.72 | V | LVV = 1001 | 157 |
| LVD Voltage | LVV | 3.6 | 3.72 | 3.84 | V | LVV = 1010 | 157 |
| LVD Voltage | LVV | 3.8 | 3.92 | 4.04 | V | LVV = 1011 | 157 |
| LVD Voltage | LVV | 4 | 4.13 | 4.26 | V | LVV = 1100 | 157 |
| LVD Voltage | LVV | 4.2 | 4.33 | 4.46 | V | LVV = 1101 | 157 |
| LVD Voltage | LVV | 4.5 | 4.64 | 4.78 | V | LVV = 1110 | 157 |
| LVD supply current | ∆ILVD | 10 | 20 | µA | 157 | ||
| LVD voltage drift temperature coefficient | TCVOUT | 15 | 50 | ppm/°C | 157 | ||
| Low-voltage Detect hysteresis | VLHYS | 100 | mV | 157 | |||
| BOR Voltage | VBOR | 2.5 | 2.58 | 2.66 | V | BORV1:0 = 11 | 158 |
| BOR Voltage | VBOR | 2.7 | 2.78 | 2.86 | V | BORV1:0 = 10 | 158 |
| BOR Voltage | VBOR | 4.2 | 4.33 | 4.46 | V | BORV1:0 = 01 | 158 |
| BOR Voltage | VBOR | 4.5 | 4.64 | 4.78 | V | BORV1:0 = 00 | 158 |
| BOR voltage drift temperature coefficient | TCVOUT | 15 | 50 | ppm/°C | 158 | ||
| BOR hysteresis | VBHYS | 100 | mV | 158 | |||
| BOR supply current | ∆IBOR | 10 | 20 | µA | 158 | ||
| Ambient temperature under bias | -55 | 125 | °C | 151 | |||
| Storage temperature | -65 | 150 | °C | 151 | |||
| Voltage on VDD with respect to VSS | VDD | -0.3 | 7.5 | V | 151 | ||
| Voltage on MCLR with respect to VSS | 0 | 8.5 | V | Note 2 | 151 | ||
| Voltage on RA4 with respect to VSS | 0 | 8.5 | V | 151 | |||
| Total power dissipation | Pdis | 1 | W | Note 1 | 151 | ||
| Maximum current out of VSS pin | 300 | mA | 151 | ||||
| Input clamp current | IIK | -20 | 20 | mA | VI < 0 or VI > VDD | 151 | |
| Output clamp current | IOK | -20 | 20 | mA | VO < 0 or VO > VDD | 151 | |
| Maximum output current sunk by any I/O pin | 25 | mA | 151 | ||||
| Maximum output current sourced by any I/O pin | 25 | mA | 151 | ||||
| Maximum current sunk by PORTA, PORTB, and PORTE (combined) | 200 | mA | Note 3 | 151 | |||
| Maximum current sourced by PORTA, PORTB, and PORTE (combined) | 200 | mA | Note 3 | 151 | |||
| Maximum current sunk by PORTC and PORTD (combined) | 200 | mA | Note 3 | 151 | |||
| Maximum current sourced by PORTC and PORTD (combined) | 200 | mA | Note 3 | 151 |
CAD (KiCad official)
- Symbol:
PIC16C774-I - Footprint:
Package_DIP:DIP-40_W15.24mm - 3D model: DIP-40_W15.24mm (KiCad packages3D, STEP)
- 3D model files:
pic16c774-i-etched.step/pic16c774-i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pic16c774-i.step/pic16c774-i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (201 pp, sha256
de0d4689f522861a, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).