Generated by kicad-footprint-generator · KiCad file format 20260206
PIC16C73B-20
Microchip Tech · Microcontroller Units (MCUs/MPUs/SOCs) · SOIC-28-300mil
PIC16C73B-20 from Microchip Tech, in a SOIC-28-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MCLR/VPP | input | Master clear (RESET) input, active low, or programming voltage input. |
| 2 | RA0/AN0 | bidirectional | PORTA bit 0 bi-directional I/O with TTL input, also analog input 0 (A/D not available on PIC16C63A). |
| 3 | RA1/AN1 | bidirectional | PORTA bit 1 bi-directional I/O with TTL input, also analog input 1 (A/D not available on PIC16C63A). |
| 4 | RA2/AN2 | bidirectional | PORTA bit 2 bi-directional I/O with TTL input, also analog input 2 (A/D not available on PIC16C63A). |
| 5 | RA3/AN3/VREF | bidirectional | PORTA bit 3 bi-directional I/O with TTL input, also analog input 3 or analog reference voltage (A/D not available on PIC16C63A). |
| 6 | RA4/T0CKI | bidirectional | PORTA bit 4 bi-directional I/O with Schmitt Trigger input, also the clock input to Timer0; output is open drain type. |
| 7 | RA5/SS/AN4 | bidirectional | PORTA bit 5 bi-directional I/O with TTL input, also analog input 4 or the slave select for the synchronous serial port (A/D not available on PIC16C63A). |
| 8 | VSS | power_in | Ground reference for logic and I/O pins. |
| 9 | OSC1/CLKIN | input | Oscillator crystal input or external clock source input (Schmitt Trigger when in RC oscillator mode, CMOS input otherwise). |
| 10 | OSC2/CLKOUT | output | Oscillator crystal output connecting to crystal or resonator in crystal oscillator mode; in RC mode it outputs CLKOUT at 1/4 the OSC1 frequency denoting the instruction cycle rate. |
| 11 | RC0/T1OSO/T1CKI | bidirectional | PORTC bit 0 bi-directional I/O with Schmitt Trigger input, also the Timer1 oscillator output or Timer1 clock input. |
| 12 | RC1/T1OSI/CCP2 | bidirectional | PORTC bit 1 bi-directional I/O with Schmitt Trigger input, also the Timer1 oscillator input or Capture2 input/Compare2 output/PWM2 output. |
| 13 | RC2/CCP1 | bidirectional | PORTC bit 2 bi-directional I/O with Schmitt Trigger input, also the Capture1 input/Compare1 output/PWM1 output. |
| 14 | RC3/SCK/SCL | bidirectional | PORTC bit 3 bi-directional I/O with Schmitt Trigger input, also the synchronous serial clock input/output for both SPI and I2C modes. |
| 15 | RC4/SDI/SDA | bidirectional | PORTC bit 4 bi-directional I/O with Schmitt Trigger input, also the SPI Data In (SPI mode) or data I/O (I2C mode). |
| 16 | RC5/SDO | bidirectional | PORTC bit 5 bi-directional I/O with Schmitt Trigger input, also the SPI Data Out (SPI mode). |
| 17 | RC6/TX/CK | bidirectional | PORTC bit 6 bi-directional I/O with Schmitt Trigger input, also the USART asynchronous transmit or synchronous clock. |
| 18 | RC7/RX/DT | bidirectional | PORTC bit 7 bi-directional I/O with Schmitt Trigger input, also the USART asynchronous receive or synchronous data. |
| 19 | VSS | power_in | Ground reference for logic and I/O pins. |
| 20 | VDD | power_in | Positive supply for logic and I/O pins. |
| 21 | RB0/INT | bidirectional | PORTB bit 0 bi-directional I/O with TTL/Schmitt Trigger input when used as external interrupt, also the external interrupt pin. |
| 22 | RB1 | bidirectional | PORTB bit 1 bi-directional I/O with TTL input; PORTB supports software-programmed weak pull-ups on all inputs. |
| 23 | RB2 | bidirectional | PORTB bit 2 bi-directional I/O with TTL input; PORTB supports software-programmed weak pull-ups on all inputs. |
| 24 | RB3 | bidirectional | PORTB bit 3 bi-directional I/O with TTL input; PORTB supports software-programmed weak pull-ups on all inputs. |
| 25 | RB4 | bidirectional | PORTB bit 4 bi-directional I/O with TTL input and interrupt-on-change. |
| 26 | RB5 | bidirectional | PORTB bit 5 bi-directional I/O with TTL input and interrupt-on-change. |
| 27 | RB6 | bidirectional | PORTB bit 6 bi-directional I/O with TTL/Schmitt Trigger input (Schmitt Trigger in serial programming mode), interrupt-on-change, and serial programming clock. |
| 28 | RB7 | bidirectional | PORTB bit 7 bi-directional I/O with TTL/Schmitt Trigger input (Schmitt Trigger in serial programming mode), interrupt-on-change, and serial programming data. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-28-300mil |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 28 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Ambient temperature under bias | -55 | 125 | °C | 113 | |||
| Storage temperature | -65 | 150 | °C | 113 | |||
| Voltage on any pin with respect to VSS (except VDD, MCLR and RA4) | -0.3 | V | 113 | ||||
| Voltage on VDD with respect to VSS | VDD | -0.3 | 7.5 | V | 113 | ||
| Voltage on MCLR with respect to VSS | 0 | 13.25 | V | Note 2 | 113 | ||
| Voltage on RA4 with respect to VSS | 0 | 8.5 | V | 113 | |||
| Total power dissipation | 1 | W | Note 1 | 113 | |||
| Input clamp current | IIK | -20 | 20 | mA | VI < 0 or VI > VDD | 113 | |
| Output clamp current | IOK | -20 | 20 | mA | VO < 0 or VO > VDD | 113 | |
| Supply voltage (XT, RC and LP oscillator modes) | VDD | 4 | 5.5 | V | XT, RC and LP osc mode | 116 | |
| Supply voltage (HS oscillator mode) | VDD | 4.5 | 5.5 | V | HS osc mode | 116 | |
| Supply voltage (BOR enabled) | VDD | 5.5 | V | BOR enabled (Note 7) | 116 | ||
| Operating temperature (extended) | TA | -40 | 125 | °C | for extended (‡ PIC16C6A/65B/73B/74B-20 Standard Operating Conditions) | 116 | |
| VDD rise rate to ensure internal Power-on Reset signal | SVDD | 0.05 | V/mS | PWRT enabled (PWRTE bit clear) | 116 | ||
| Brown-out Reset voltage trip point | VBOR | 3.65 | 4.35 | V | BODEN bit set | 116 | |
| Supply current (XT, RC oscillator modes) | IDD | 2.7 | 5 | mA | XT, RC osc modes: FOSC = 4 MHz, VDD = 5.5 V (Note 4) | 117 | |
| Supply current (HS oscillator mode) | IDD | 7 | 10 | mA | HS osc mode: FOSC = 20 MHz, VDD = 5.5 V | 117 | |
| Power-down current, WDT enabled, -40°C to +85°C | IPD | 10.5 | 42 | µA | VDD = 4.0V, WDT enabled, -40°C to +85°C | 117 | |
| Power-down current, WDT disabled, 0°C to +70°C | IPD | 1.5 | 16 | µA | VDD = 4.0V, WDT disabled, 0°C to +70°C | 117 | |
| Power-down current, WDT disabled, -40°C to +85°C | IPD | 1.5 | 19 | µA | VDD = 4.0V, WDT disabled, -40°C to +85°C | 117 | |
| Power-down current, WDT disabled, -40°C to +125°C | IPD | 2.5 | 19 | µA | VDD = 4.0V, WDT disabled, -40°C to +125°C | 117 | |
| Watchdog Timer module differential current | IWDT | 6 | 20 | µA | WDTE bit set, VDD = 4.0V | 118 | |
| Brown-out Reset module differential current | IBOR | 100 | 150 | µA | BODEN bit set, VDD = 5.0 | 118 | |
| Input low voltage, I/O ports with TTL buffer (4.5 V to 5.5 V) | VIL | 0.8 | V | 4.5V ≤ VDD ≤ 5.5V | 118 | ||
| Input high voltage, I/O ports with TTL buffer | VIH | 2 | V | 4.5 V ≤ VDD ≤ 5.5V | 119 | ||
| Input leakage current, I/O ports | IIL | -1 | 1 | µA | VSS ≤ VPIN ≤ VDD, pin at hi-impedance | 119 | |
| Input leakage current, MCLR, RA4/T0CKI | IIL | -5 | 5 | µA | VSS ≤ VPIN ≤ VDD | 119 | |
| Input leakage current, OSC1 | IIL | -5 | 5 | µA | VSS ≤ VPIN ≤ VDD, XT, HS and LP osc modes | 119 | |
| PORTB weak pull-up current | IPURB | 50 | 250 | 400 | µA | VDD = 5V, VPIN = VSS | 119 |
| Output low voltage, I/O ports (-40°C to +85°C) | VOL | 0.6 | V | IOL = 8.5 mA, VDD = 4.5V, -40°C to +85°C | 120 | ||
| Output low voltage, I/O ports (-40°C to +125°C) | VOL | 0.6 | V | IOL = 7.0 mA, VDD = 4.5V, -40°C to +125°C | 120 | ||
| Output low voltage, OSC2/CLKOUT (RC mode, -40°C to +85°C) | VOL | 0.6 | V | IOL = 1.6 mA, VDD = 4.5V, -40°C to +85°C | 120 | ||
| Output low voltage, OSC2/CLKOUT (RC mode, -40°C to +125°C) | VOL | 0.6 | V | IOL = 1.2 mA, VDD = 4.5V, -40°C to +125°C | 120 | ||
| Open-drain high voltage, RA4 pin | VOD | 8.5 | V | RA4 pin | 120 | ||
| Capacitive loading, OSC2 pin | COSC2 | 15 | pF | In XT, HS and LP modes when external clock is used to drive OSC1 | 121 | ||
| Capacitive loading, all I/O pins and OSC2 (RC mode) | CIO | 50 | pF | 121 | |||
| Capacitive loading, SCL, SDA | Cb | 400 | pF | in I2C mode | 121 | ||
| External CLKIN frequency (HS oscillator, -20) | FOSC | 20 | MHz | HS osc mode (-20) | 124 | ||
| External CLKIN period (HS oscillator, -20) | TOSC | 50 | ns | HS osc mode (-20) | 124 | ||
| Instruction cycle time | TCY | 200 | ns | TCY = 4/FOSC | 124 | ||
| External clock in (OSC1) high or low time | TosL, TosH | 15 | ns | HS oscillator | 124 | ||
| External clock in (OSC1) rise or fall time | TosR, TosF | 15 | ns | HS oscillator | 124 | ||
| OSC1 to CLKOUT (falling) | TosH2ckL | 75 | 200 | ns | Note 1 | 125 | |
| OSC1 to CLKOUT (rising) | TosH2ckH | 75 | 200 | ns | Note 1 | 125 | |
| CLKOUT rise time | TckR | 35 | 100 | ns | Note 1 | 125 | |
| CLKOUT fall time | TckF | 35 | 100 | ns | Note 1 | 125 | |
| OSC1 (Q1 cycle) to port output valid | TosH2ioV | 50 | 150 | ns | 125 | ||
| OSC1 (Q2 cycle) to port input invalid (I/O in hold time) | TosH2ioI | 100 | ns | PIC16CXX | 125 | ||
| Port output rise time | TioR | 10 | 40 | ns | PIC16CXX | 125 | |
| Port output fall time | TioF | 10 | 40 | ns | PIC16CXX | 125 | |
| A/D reference voltage | VREF | 2.5 | V | 137 | |||
| Recommended impedance of analog voltage source | ZAIN | 10 | kΩ | 137 |
CAD (KiCad official)
- Symbol:
PIC16C73B-20 - Footprint:
Package_SO:SOIC-28W_7.5x17.9mm_P1.27mm - 3D model: SOIC-28-300mil (KiCad packages3D, STEP)
- 3D model files:
pic16c73b-20-so-etched.step/pic16c73b-20-so-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pic16c73b-20-so.step/pic16c73b-20-so.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (186 pp, sha256
35c8a32ee8686aa6, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).