3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownPCF8574AM
HGSEMI · I/O Expanders · SOP-16-150mil
PCF8574AM from HGSEMI, in a SOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | A0 | input | Address input 0 sets hardware slave address bit A0, allowing up to 8 PCF8574 devices (up to 16 with PCF8574A) on the bus. |
| 2 | A1 | input | Address input 1 sets hardware slave address bit A1, allowing up to 8 PCF8574 devices (up to 16 with PCF8574A) on the bus. |
| 3 | A2 | input | Address input 2 sets hardware slave address bit A2, allowing up to 8 PCF8574 devices (up to 16 with PCF8574A) on the bus. |
| 4 | P0 | bidirectional | Quasi-bidirectional I/O 0 can be used as input or output without a direction control signal; it powers up HIGH and should be HIGH before being used as an input. |
| 5 | P1 | bidirectional | Quasi-bidirectional I/O 1 can be used as input or output without a direction control signal; it powers up HIGH and should be HIGH before being used as an input. |
| 6 | P2 | bidirectional | Quasi-bidirectional I/O 2 can be used as input or output without a direction control signal; it powers up HIGH and should be HIGH before being used as an input. |
| 7 | P3 | bidirectional | Quasi-bidirectional I/O 3 can be used as input or output without a direction control signal; it powers up HIGH and should be HIGH before being used as an input. |
| 8 | VSS | power_in | Supply ground, the 0 V reference for the 2.5 to 6 V supply range. |
| 9 | P4 | bidirectional | Quasi-bidirectional I/O 4 can be used as input or output without a direction control signal; it powers up HIGH and should be HIGH before being used as an input. |
| 10 | P5 | bidirectional | Quasi-bidirectional I/O 5 can be used as input or output without a direction control signal; it powers up HIGH and should be HIGH before being used as an input. |
| 11 | P6 | bidirectional | Quasi-bidirectional I/O 6 can be used as input or output without a direction control signal; it powers up HIGH and should be HIGH before being used as an input. |
| 12 | P7 | bidirectional | Quasi-bidirectional I/O 7 can be used as input or output without a direction control signal; it powers up HIGH and should be HIGH before being used as an input. |
| 13 | INT | output | Open-drain interrupt output, active LOW, signals the microcontroller when input data on the ports changes; minimum IOL is 1.6 mA at VOL 0.4 V. |
| 14 | SCL | input | Serial clock line of the I2C-bus, which must be pulled up to the positive supply through a pull-up resistor; maximum fSCL is 100 kHz. |
| 15 | SDA | bidirectional | Serial data line of the I2C-bus, which must be pulled up to the positive supply through a pull-up resistor; the data must remain stable during the HIGH period of the clock. |
| 16 | VDD | power_in | Supply voltage of 2.5 to 6.0 V; the device resets the I2C logic when VDD falls below VPOR (2.4 V maximum). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HGSEMI |
| Package | SOP-16-150mil |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 16 |
CAD (KiCad official)
- Symbol:
PCF8574AM - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOP-16-150mil (KiCad packages3D, STEP)
- 3D model files:
pcf8574am-etched.step/pcf8574am-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pcf8574am.step/pcf8574am.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: HGSEMI datasheet, copy hosted by LCSC (18 pp, sha256
b4f2128e4d380a5d, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).