main
Ray
Publish 0.1.0
3ef7464
PCA9551D
NXP Semicon · LED Drivers · SO-16-150mil
PCA9551D from NXP Semicon, in a SO-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | A0 | input | Hardware address input 0 sets the device's slave address and must be pulled HIGH or LOW because no internal pull-up resistor is fitted. |
| 2 | A1 | input | Hardware address input 1 sets the device's slave address and must be pulled HIGH or LOW because no internal pull-up resistor is fitted. |
| 3 | A2 | input | Hardware address input 2 sets the device's slave address and must be pulled HIGH or LOW because no internal pull-up resistor is fitted. |
| 4 | LED0 | bidirectional | LED driver 0 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 5 | LED1 | bidirectional | LED driver 1 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 6 | LED2 | bidirectional | LED driver 2 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 7 | LED3 | bidirectional | LED driver 3 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 8 | VSS | power_in | Supply ground; it must be connected to the supply ground for proper device operation. |
| 9 | LED4 | bidirectional | LED driver 4 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 10 | LED5 | bidirectional | LED driver 5 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 11 | LED6 | bidirectional | LED driver 6 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 12 | LED7 | bidirectional | LED driver 7 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 13 | RESET | input | Active LOW reset input that initializes the registers to their default state, all zeroes, when pulled LOW. |
| 14 | SCL | input | I2C-bus serial clock line with a noise filter, operating from 0 Hz to 400 kHz. |
| 15 | SDA | bidirectional | I2C-bus serial data line with a noise filter, operating from 0 Hz to 400 kHz. |
| 16 | VDD | power_in | Supply voltage with an operating range of 2.3 V to 5.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | NXP Semicon |
| Package | SO-16-150mil |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| supply voltage | VDD | -0.5 | 6 | V | 12 | ||
| voltage on an input/output pin | VI/O | 5.5 | V | min printed as VSS − 0.5 | 12 | ||
| output current on pin LEDn | IO(LEDn) | 25 | mA | printed as ±25 mA | 12 | ||
| ground supply current | ISS | 100 | mA | 12 | |||
| total power dissipation | Ptot | 400 | mW | 12 | |||
| storage temperature | Tstg | -65 | 150 | °C | 12 | ||
| ambient temperature operating | Tamb | -40 | 85 | °C | operating | 12 | |
| supply voltage | VDD | 2.3 | 5.5 | V | 13 | ||
| supply current | IDD | 350 | 500 | µA | operating mode; VDD = 5.5 V; VI =VDD or VSS; fSCL = 100 kHz | 13 | |
| standby current | Istb | 1.9 | 3 | µA | Standby mode; VDD = 5.5 V; VI =VDD or VSS; fSCL = 0 kHz | 13 | |
| additional quiescent supply current | ∆IDD | 800 | µA | Standby mode; VDD = 5.5 V; every LED I/O at VI = 4.3 V; fSCL = 0 kHz | 13 | ||
| power-on reset voltage | VPOR | 1.7 | 2.2 | V | no load; VI =VDD or VSS | 13 | |
| LOW-level input voltage SCL, SDA | VIL | -0.5 | V | Input SCL; input/output SDA; max printed as +0.3VDD | 13 | ||
| HIGH-level input voltage SCL, SDA | VIH | 5.5 | V | Input SCL; input/output SDA; min printed as 0.7VDD | 13 | ||
| LOW-level output current SDA | IOL | 3 | 6.5 | mA | VOL = 0.4 V | 13 | |
| leakage current SCL, SDA | IL | -1 | 1 | µA | VI =VDD =VSS | 13 | |
| input capacitance SCL | Ci | 3.7 | 5 | pF | VI =VSS | 13 | |
| LOW-level input voltage I/Os | VIL | -0.5 | 0.8 | V | 13 | ||
| HIGH-level input voltage I/Os | VIH | 2 | 5.5 | V | 13 | ||
| LOW-level output current I/Os | IOL | 6 | 9 | mA | VOL = 0.4 V; VDD = 2.3 V [3] | 13 | |
| LOW-level output current I/Os | IOL | 8 | 11 | mA | VOL = 0.4 V; VDD = 3.0 V [3] | 13 | |
| LOW-level output current I/Os | IOL | 10 | 14 | mA | VOL = 0.4 V; VDD = 5.0 V [3] | 13 | |
| LOW-level output current I/Os | IOL | 11 | 14 | mA | VOL = 0.7 V; VDD = 2.3 V [3] | 13 | |
| LOW-level output current I/Os | IOL | 14 | 18 | mA | VOL = 0.7 V; VDD = 3.0 V [3] | 13 | |
| LOW-level output current I/Os | IOL | 17 | 24 | mA | VOL = 0.7 V; VDD = 5.0 V [3] | 13 | |
| input leakage current I/Os | ILI | -1 | 1 | µA | VDD = 3.6 V; VI = 0 V or VDD | 13 | |
| input/output capacitance | Cio | 2.1 | 5 | pF | 13 | ||
| LOW-level input voltage A0, A1, A2, RESET | VIL | -0.5 | 0.8 | V | 13 | ||
| HIGH-level input voltage A0, RESET | VIH | 2 | 5.5 | V | A0; RESET | 13 | |
| HIGH-level input voltage A1, A2 | VIH | 2 | V | A1; A2; max printed as VDD + 0.5 | 13 | ||
| input leakage current select inputs | ILI | -1 | 1 | µA | 13 | ||
| input capacitance select inputs | Ci | 2.3 | 5 | pF | 13 | ||
| SCL clock frequency | fSCL | 0 | 100 | kHz | Standard-mode I2C-bus | 15 | |
| SCL clock frequency | fSCL | 0 | 400 | kHz | Fast-mode I2C-bus | 15 | |
| bus free time between a STOP and START condition | tBUF | 4.7 | µs | Standard-mode I2C-bus | 15 | ||
| bus free time between a STOP and START condition | tBUF | 1.3 | µs | Fast-mode I2C-bus | 15 | ||
| hold time (repeated) START condition | tHD;STA | 4 | µs | Standard-mode I2C-bus | 15 | ||
| hold time (repeated) START condition | tHD;STA | 0.6 | µs | Fast-mode I2C-bus | 15 | ||
| set-up time for a repeated START condition | tSU;STA | 4.7 | µs | Standard-mode I2C-bus | 15 | ||
| set-up time for a repeated START condition | tSU;STA | 0.6 | µs | Fast-mode I2C-bus | 15 | ||
| set-up time for STOP condition | tSU;STO | 4 | µs | Standard-mode I2C-bus | 15 | ||
| set-up time for STOP condition | tSU;STO | 0.6 | µs | Fast-mode I2C-bus | 15 | ||
| data hold time | tHD;DAT | 0 | ns | Standard-mode I2C-bus | 15 | ||
| LOW period of the SCL clock | tLOW | 4.7 | µs | Standard-mode I2C-bus | 15 | ||
| LOW period of the SCL clock | tLOW | 1.3 | µs | Fast-mode I2C-bus | 15 | ||
| HIGH period of the SCL clock | tHIGH | 4 | µs | Standard-mode I2C-bus | 15 | ||
| HIGH period of the SCL clock | tHIGH | 0.6 | µs | Fast-mode I2C-bus | 15 | ||
| data set-up time | tSU;DAT | 250 | ns | Standard-mode I2C-bus | 15 | ||
| data set-up time | tSU;DAT | 100 | ns | Fast-mode I2C-bus | 15 | ||
| rise time of both SDA and SCL signals | tr | 1000 | ns | Standard-mode I2C-bus | 15 | ||
| rise time of both SDA and SCL signals | tr | 300 | ns | Fast-mode I2C-bus; min printed as 20 + 0.1Cb [3] | 15 | ||
| fall time of both SDA and SCL signals | tf | 300 | ns | Standard-mode I2C-bus | 15 | ||
| reset pulse width | tw(rst) | 8 | ns | Standard-mode I2C-bus | 15 | ||
| reset recovery time | trec(rst) | 0 | ns | Standard-mode I2C-bus | 15 | ||
| reset time | trst | 400 | ns | Standard-mode I2C-bus | 15 |
CAD (KiCad official)
- Symbol:
PCA9551D - Footprint:
Package_SO:SO-16_3.9x9.9mm_P1.27mm - 3D model: SO-16-150mil (KiCad packages3D, STEP)
- 3D model files:
pca9551d-etched.step/pca9551d-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pca9551d.step/pca9551d.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: NXP Semicon datasheet (26 pp, sha256
06eed5605dc2a71f, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# PCA9551D
**NXP Semicon** · LED Drivers · SO-16-150mil
PCA9551D from NXP Semicon, in a SO-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | A0 | input | Hardware address input 0 sets the device's slave address and must be pulled HIGH or LOW because no internal pull-up resistor is fitted. |
| 2 | A1 | input | Hardware address input 1 sets the device's slave address and must be pulled HIGH or LOW because no internal pull-up resistor is fitted. |
| 3 | A2 | input | Hardware address input 2 sets the device's slave address and must be pulled HIGH or LOW because no internal pull-up resistor is fitted. |
| 4 | LED0 | bidirectional | LED driver 0 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 5 | LED1 | bidirectional | LED driver 1 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 6 | LED2 | bidirectional | LED driver 2 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 7 | LED3 | bidirectional | LED driver 3 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 8 | VSS | power_in | Supply ground; it must be connected to the supply ground for proper device operation. |
| 9 | LED4 | bidirectional | LED driver 4 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 10 | LED5 | bidirectional | LED driver 5 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 11 | LED6 | bidirectional | LED driver 6 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 12 | LED7 | bidirectional | LED driver 7 is an open-drain output rated to sink up to 25 mA, and it can also be used as a GPIO when not driving an LED. |
| 13 | RESET | input | Active LOW reset input that initializes the registers to their default state, all zeroes, when pulled LOW. |
| 14 | SCL | input | I2C-bus serial clock line with a noise filter, operating from 0 Hz to 400 kHz. |
| 15 | SDA | bidirectional | I2C-bus serial data line with a noise filter, operating from 0 Hz to 400 kHz. |
| 16 | VDD | power_in | Supply voltage with an operating range of 2.3 V to 5.5 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | NXP Semicon |
| Package | SO-16-150mil |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| supply voltage | VDD | -0.5 | | 6 | V | | 12 |
| voltage on an input/output pin | VI/O | | | 5.5 | V | min printed as VSS − 0.5 | 12 |
| output current on pin LEDn | IO(LEDn) | | | 25 | mA | printed as ±25 mA | 12 |
| ground supply current | ISS | | | 100 | mA | | 12 |
| total power dissipation | Ptot | | | 400 | mW | | 12 |
| storage temperature | Tstg | -65 | | 150 | °C | | 12 |
| ambient temperature operating | Tamb | -40 | | 85 | °C | operating | 12 |
| supply voltage | VDD | 2.3 | | 5.5 | V | | 13 |
| supply current | IDD | | 350 | 500 | µA | operating mode; VDD = 5.5 V; VI =VDD or VSS; fSCL = 100 kHz | 13 |
| standby current | Istb | | 1.9 | 3 | µA | Standby mode; VDD = 5.5 V; VI =VDD or VSS; fSCL = 0 kHz | 13 |
| additional quiescent supply current | ∆IDD | | | 800 | µA | Standby mode; VDD = 5.5 V; every LED I/O at VI = 4.3 V; fSCL = 0 kHz | 13 |
| power-on reset voltage | VPOR | | 1.7 | 2.2 | V | no load; VI =VDD or VSS | 13 |
| LOW-level input voltage SCL, SDA | VIL | -0.5 | | | V | Input SCL; input/output SDA; max printed as +0.3VDD | 13 |
| HIGH-level input voltage SCL, SDA | VIH | | | 5.5 | V | Input SCL; input/output SDA; min printed as 0.7VDD | 13 |
| LOW-level output current SDA | IOL | 3 | 6.5 | | mA | VOL = 0.4 V | 13 |
| leakage current SCL, SDA | IL | -1 | | 1 | µA | VI =VDD =VSS | 13 |
| input capacitance SCL | Ci | | 3.7 | 5 | pF | VI =VSS | 13 |
| LOW-level input voltage I/Os | VIL | -0.5 | | 0.8 | V | | 13 |
| HIGH-level input voltage I/Os | VIH | 2 | | 5.5 | V | | 13 |
| LOW-level output current I/Os | IOL | 6 | 9 | | mA | VOL = 0.4 V; VDD = 2.3 V [3] | 13 |
| LOW-level output current I/Os | IOL | 8 | 11 | | mA | VOL = 0.4 V; VDD = 3.0 V [3] | 13 |
| LOW-level output current I/Os | IOL | 10 | 14 | | mA | VOL = 0.4 V; VDD = 5.0 V [3] | 13 |
| LOW-level output current I/Os | IOL | 11 | 14 | | mA | VOL = 0.7 V; VDD = 2.3 V [3] | 13 |
| LOW-level output current I/Os | IOL | 14 | 18 | | mA | VOL = 0.7 V; VDD = 3.0 V [3] | 13 |
| LOW-level output current I/Os | IOL | 17 | 24 | | mA | VOL = 0.7 V; VDD = 5.0 V [3] | 13 |
| input leakage current I/Os | ILI | -1 | | 1 | µA | VDD = 3.6 V; VI = 0 V or VDD | 13 |
| input/output capacitance | Cio | | 2.1 | 5 | pF | | 13 |
| LOW-level input voltage A0, A1, A2, RESET | VIL | -0.5 | | 0.8 | V | | 13 |
| HIGH-level input voltage A0, RESET | VIH | 2 | | 5.5 | V | A0; RESET | 13 |
| HIGH-level input voltage A1, A2 | VIH | 2 | | | V | A1; A2; max printed as VDD + 0.5 | 13 |
| input leakage current select inputs | ILI | -1 | | 1 | µA | | 13 |
| input capacitance select inputs | Ci | | 2.3 | 5 | pF | | 13 |
| SCL clock frequency | fSCL | 0 | | 100 | kHz | Standard-mode I2C-bus | 15 |
| SCL clock frequency | fSCL | 0 | | 400 | kHz | Fast-mode I2C-bus | 15 |
| bus free time between a STOP and START condition | tBUF | 4.7 | | | µs | Standard-mode I2C-bus | 15 |
| bus free time between a STOP and START condition | tBUF | 1.3 | | | µs | Fast-mode I2C-bus | 15 |
| hold time (repeated) START condition | tHD;STA | 4 | | | µs | Standard-mode I2C-bus | 15 |
| hold time (repeated) START condition | tHD;STA | 0.6 | | | µs | Fast-mode I2C-bus | 15 |
| set-up time for a repeated START condition | tSU;STA | 4.7 | | | µs | Standard-mode I2C-bus | 15 |
| set-up time for a repeated START condition | tSU;STA | 0.6 | | | µs | Fast-mode I2C-bus | 15 |
| set-up time for STOP condition | tSU;STO | 4 | | | µs | Standard-mode I2C-bus | 15 |
| set-up time for STOP condition | tSU;STO | 0.6 | | | µs | Fast-mode I2C-bus | 15 |
| data hold time | tHD;DAT | 0 | | | ns | Standard-mode I2C-bus | 15 |
| LOW period of the SCL clock | tLOW | 4.7 | | | µs | Standard-mode I2C-bus | 15 |
| LOW period of the SCL clock | tLOW | 1.3 | | | µs | Fast-mode I2C-bus | 15 |
| HIGH period of the SCL clock | tHIGH | 4 | | | µs | Standard-mode I2C-bus | 15 |
| HIGH period of the SCL clock | tHIGH | 0.6 | | | µs | Fast-mode I2C-bus | 15 |
| data set-up time | tSU;DAT | 250 | | | ns | Standard-mode I2C-bus | 15 |
| data set-up time | tSU;DAT | 100 | | | ns | Fast-mode I2C-bus | 15 |
| rise time of both SDA and SCL signals | tr | | | 1000 | ns | Standard-mode I2C-bus | 15 |
| rise time of both SDA and SCL signals | tr | | | 300 | ns | Fast-mode I2C-bus; min printed as 20 + 0.1Cb [3] | 15 |
| fall time of both SDA and SCL signals | tf | | | 300 | ns | Standard-mode I2C-bus | 15 |
| reset pulse width | tw(rst) | 8 | | | ns | Standard-mode I2C-bus | 15 |
| reset recovery time | trec(rst) | 0 | | | ns | Standard-mode I2C-bus | 15 |
| reset time | trst | 400 | | | ns | Standard-mode I2C-bus | 15 |
## CAD (KiCad official)
- Symbol: `PCA9551D`
- Footprint: `Package_SO:SO-16_3.9x9.9mm_P1.27mm`
- 3D model: SO-16-150mil (KiCad packages3D, STEP)
- 3D model files: `pca9551d-etched.step` / `pca9551d-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `pca9551d.step` / `pca9551d.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [NXP Semicon datasheet](https://www.nxp.com/docs/en/data-sheet/PCA9551D.pdf) (26 pp, sha256 `06eed5605dc2a71f`, retrieved 2026-11-20)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/pca9551d-datasheet.pdf)