main
Ray
Publish 0.1.2
82ef3fb
PCA8561BHN
NXP Semicon · LCD Drivers · HVQFN-32-EP(5x5)
PCA8561BHN from NXP Semicon, in a HVQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | COM3 | output | LCD backplane output that must be directly connected to the LCD; in 1:3 multiplex mode it carries the same signal as COM1 and may be tied to it. |
| 2 | VLCD | power_in | LCD supply voltage, specified 1.8 V to 5.5 V; VLCD must never be asserted before VDD and must never be connected while VDD is switched off. |
| 3 | VDD | power_in | Supply voltage, specified 1.8 V to 5.5 V, with a decoupling capacitor of at least 100 nF recommended. |
| 4 | VSS | power_in | Ground supply; the die paddle (exposed pad) is connected to VSS and should be electrically isolated. |
| 5 | RST | input | Reset input, active LOW; when the internal POR is disabled the chip must be reset by holding RST at logic 0 for at least 10 µs. |
| 6 | SDIO | bidirectional | SPI-bus serial data input/output; input data are sampled on the rising edge of SCL and output data are valid after the falling edge of SCL. |
| 7 | CLK | bidirectional | Internal oscillator output or external oscillator input; must be left open if unused. |
| 8 | SCL | input | Serial clock input for the SPI-bus; the input may be higher than VDD. |
| 9 | CE | input | Chip enable input, active LOW; the SPI interface is reset while CE is HIGH, and CE must not be wired permanently LOW. |
| 10 | PORE | input | Power-On Reset enable: connect to VDD to enable the internal POR, or connect to VSS (or leave open) to disable it; series resistance between VDD and this pin must not exceed 1 kΩ. |
| 11 | n.c. | unconnected | Not connected. |
| 12 | SEG0 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 13 | SEG1 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 14 | SEG2 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 15 | SEG3 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 16 | SEG4 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 17 | SEG5 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 18 | SEG6 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 19 | SEG7 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 20 | SEG8 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 21 | SEG9 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 22 | SEG10 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 23 | SEG11 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 24 | SEG12 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 25 | SEG13 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 26 | SEG14 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 27 | SEG15 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 28 | SEG16 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 29 | SEG17 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 30 | COM0 | output | LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode. |
| 31 | COM1 | output | LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode. |
| 32 | COM2 | output | LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | NXP Semicon |
| Package | HVQFN-32-EP(5x5) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Limiting values: supply voltage VDD | VDD | -0.5 | 6.5 | V | 29 | ||
| Limiting values: LCD supply voltage | VLCD | -0.5 | 6.5 | V | 29 | ||
| Limiting values: input voltage | VI | -0.5 | 6.5 | V | 29 | ||
| Limiting values: output voltage | VO | -0.5 | 6.5 | V | 29 | ||
| Limiting values: input current | II | -10 | 10 | mA | 29 | ||
| Limiting values: output current | IO | -10 | 10 | mA | 29 | ||
| Limiting values: supply current | IDD | -50 | 50 | mA | 29 | ||
| Limiting values: LCD supply current | IDD(LCD) | -50 | 50 | mA | 29 | ||
| Limiting values: ground supply current | ISS | -50 | 50 | mA | 29 | ||
| Limiting values: total power dissipation | Ptot | 100 | mW | 29 | |||
| Limiting values: output power | Po | 100 | mW | 29 | |||
| Limiting values: ESD HBM voltage | VESD | -2000 | 2000 | V | HBM, on pins SCL, SDA, CE; pass level | 29 | |
| Limiting values: ESD HBM voltage | VESD | -3500 | 3500 | V | HBM, on all other pins; pass level | 29 | |
| Limiting values: ESD CDM voltage | VESD | -2000 | 2000 | V | CDM; pass level | 29 | |
| Limiting values: latch-up current | Ilu | 200 | mA | latch-up test at maximum ambient temperature; pass level | 29 | ||
| Limiting values: storage temperature | Tstg | -55 | 150 | °C | 29 | ||
| Limiting values: ambient temperature operating device | Tamb | -40 | 105 | °C | operating device | 29 | |
| Supply voltage VDD | VDD | 1.8 | 5.5 | V | 30 | ||
| LCD supply voltage | VLCD | 1.8 | 5.5 | V | 30 | ||
| Ambient temperature range (operating) | Tamb | -40 | 105 | °C | unless otherwise specified (Characteristics header) | 30 | |
| Supply current IDD | IDD | 1.8 | 3 | μA | ffr = 64 Hz; no bus activity; VDD = 5.5 V; Tamb = 105 °C | 30 | |
| LCD supply current IDD(LCD) | IDD(LCD) | 3.7 | 4.7 | μA | ffr = 64 Hz; no bus activity; VLCD = 5.5 V; Tamb = 105 °C; BOOST = 0; no display load | 30 | |
| LOW-level output sink current on pin CLK | IOL | 2 | mA | output sink current; VOL = 0.4 V; VDD = 5 V; on pin CLK | 30 | ||
| LOW-level output sink current on pin SDIO | IOL | 2 | mA | output sink current; VOL = 0.4 V; VDD = 5 V; on pin SDIO | 30 | ||
| LOW-level output sink current on pin SDA | IOL | 3 | mA | output sink current; VOL = 0.4 V; VDD = 5 V; on pin SDA | 30 | ||
| HIGH-level output source current | IOH | 2 | mA | output source current; on pins SDIO, CLK; VOH = 4.6 V; VDD = 5 V | 30 | ||
| Leakage current after ESD event | IL | -500 | 500 | nA | after ESD event | 30 | |
| Output voltage variation | ΔVo | -100 | 100 | mV | VLCD = 5 V | 30 | |
| Output resistance | Ro | 1.5 | 3 | kΩ | VLCD = 5 V; outputs measured one at a time | 31 | |
| Frame frequency ffr | ffr | 42 | 64 | 86 | Hz | FF[2:0] = 001 | 33 |
| External clock frequency | fclk(ext) | 4096 | Hz | 33 | |||
| HIGH-level clock time | tclk(H) | 60 | μs | external clock | 33 | ||
| LOW-level clock time | tclk(L) | 60 | μs | external clock | 33 | ||
| Reset pulse width | tw(rst) | 10 | μs | reset pulse width on pin RST | 33 | ||
| SCL clock frequency (SPI-bus) | fSCL | 5 | MHz | 35 | |||
| LOW period of the SCL clock (SPI-bus) | tLOW | 150 | ns | 35 | |||
| HIGH period of the SCL clock (SPI-bus) | tHIGH | 80 | ns | 35 | |||
| Rise time (SPI-bus) | tr | 100 | ns | 35 | |||
| Fall time (SPI-bus) | tf | 100 | ns | 35 | |||
| CE_N set-up time | tsu(CE_N) | 30 | ns | 36 | |||
| CE_N hold time | th(CE_N) | 10 | ns | 36 | |||
| CE_N recovery time | trec(CE_N) | 70 | ns | 36 | |||
| SDIO set-up time write data | tsu | 5 | ns | write data | 36 | ||
| SDIO hold time write data | th | 50 | ns | write data | 36 | ||
| SDIO read delay time | td(R)SDIO | 150 | ns | CL = 50 pF | 36 | ||
| SDIO disable time | tdis(SDIO) | 50 | ns | no load | 36 | ||
| Transition time from SDI to SDO | tt(SDI-SDO) | 0 | ns | write to read mode | 36 |
CAD (KiCad official)
- Symbol:
PCA8561BHN - Footprint:
Package_DFN_QFN:HVQFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm - 3D model: HVQFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
pca8561bhn-ay-etched.step/pca8561bhn-ay-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pca8561bhn-ay.step/pca8561bhn-ay.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: NXP Semicon datasheet (50 pp, sha256
49517ebdf09b65e8, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# PCA8561BHN
**NXP Semicon** · LCD Drivers · HVQFN-32-EP(5x5)
PCA8561BHN from NXP Semicon, in a HVQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | COM3 | output | LCD backplane output that must be directly connected to the LCD; in 1:3 multiplex mode it carries the same signal as COM1 and may be tied to it. |
| 2 | VLCD | power_in | LCD supply voltage, specified 1.8 V to 5.5 V; VLCD must never be asserted before VDD and must never be connected while VDD is switched off. |
| 3 | VDD | power_in | Supply voltage, specified 1.8 V to 5.5 V, with a decoupling capacitor of at least 100 nF recommended. |
| 4 | VSS | power_in | Ground supply; the die paddle (exposed pad) is connected to VSS and should be electrically isolated. |
| 5 | RST | input | Reset input, active LOW; when the internal POR is disabled the chip must be reset by holding RST at logic 0 for at least 10 µs. |
| 6 | SDIO | bidirectional | SPI-bus serial data input/output; input data are sampled on the rising edge of SCL and output data are valid after the falling edge of SCL. |
| 7 | CLK | bidirectional | Internal oscillator output or external oscillator input; must be left open if unused. |
| 8 | SCL | input | Serial clock input for the SPI-bus; the input may be higher than VDD. |
| 9 | CE | input | Chip enable input, active LOW; the SPI interface is reset while CE is HIGH, and CE must not be wired permanently LOW. |
| 10 | PORE | input | Power-On Reset enable: connect to VDD to enable the internal POR, or connect to VSS (or leave open) to disable it; series resistance between VDD and this pin must not exceed 1 kΩ. |
| 11 | n.c. | unconnected | Not connected. |
| 12 | SEG0 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 13 | SEG1 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 14 | SEG2 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 15 | SEG3 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 16 | SEG4 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 17 | SEG5 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 18 | SEG6 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 19 | SEG7 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 20 | SEG8 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 21 | SEG9 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 22 | SEG10 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 23 | SEG11 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 24 | SEG12 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 25 | SEG13 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 26 | SEG14 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 27 | SEG15 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 28 | SEG16 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 29 | SEG17 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |
| 30 | COM0 | output | LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode. |
| 31 | COM1 | output | LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode. |
| 32 | COM2 | output | LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | NXP Semicon |
| Package | HVQFN-32-EP(5x5) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 33 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Limiting values: supply voltage VDD | VDD | -0.5 | | 6.5 | V | | 29 |
| Limiting values: LCD supply voltage | VLCD | -0.5 | | 6.5 | V | | 29 |
| Limiting values: input voltage | VI | -0.5 | | 6.5 | V | | 29 |
| Limiting values: output voltage | VO | -0.5 | | 6.5 | V | | 29 |
| Limiting values: input current | II | -10 | | 10 | mA | | 29 |
| Limiting values: output current | IO | -10 | | 10 | mA | | 29 |
| Limiting values: supply current | IDD | -50 | | 50 | mA | | 29 |
| Limiting values: LCD supply current | IDD(LCD) | -50 | | 50 | mA | | 29 |
| Limiting values: ground supply current | ISS | -50 | | 50 | mA | | 29 |
| Limiting values: total power dissipation | Ptot | | | 100 | mW | | 29 |
| Limiting values: output power | Po | | | 100 | mW | | 29 |
| Limiting values: ESD HBM voltage | VESD | -2000 | | 2000 | V | HBM, on pins SCL, SDA, CE; pass level | 29 |
| Limiting values: ESD HBM voltage | VESD | -3500 | | 3500 | V | HBM, on all other pins; pass level | 29 |
| Limiting values: ESD CDM voltage | VESD | -2000 | | 2000 | V | CDM; pass level | 29 |
| Limiting values: latch-up current | Ilu | | | 200 | mA | latch-up test at maximum ambient temperature; pass level | 29 |
| Limiting values: storage temperature | Tstg | -55 | | 150 | °C | | 29 |
| Limiting values: ambient temperature operating device | Tamb | -40 | | 105 | °C | operating device | 29 |
| Supply voltage VDD | VDD | 1.8 | | 5.5 | V | | 30 |
| LCD supply voltage | VLCD | 1.8 | | 5.5 | V | | 30 |
| Ambient temperature range (operating) | Tamb | -40 | | 105 | °C | unless otherwise specified (Characteristics header) | 30 |
| Supply current IDD | IDD | | 1.8 | 3 | μA | ffr = 64 Hz; no bus activity; VDD = 5.5 V; Tamb = 105 °C | 30 |
| LCD supply current IDD(LCD) | IDD(LCD) | | 3.7 | 4.7 | μA | ffr = 64 Hz; no bus activity; VLCD = 5.5 V; Tamb = 105 °C; BOOST = 0; no display load | 30 |
| LOW-level output sink current on pin CLK | IOL | 2 | | | mA | output sink current; VOL = 0.4 V; VDD = 5 V; on pin CLK | 30 |
| LOW-level output sink current on pin SDIO | IOL | 2 | | | mA | output sink current; VOL = 0.4 V; VDD = 5 V; on pin SDIO | 30 |
| LOW-level output sink current on pin SDA | IOL | 3 | | | mA | output sink current; VOL = 0.4 V; VDD = 5 V; on pin SDA | 30 |
| HIGH-level output source current | IOH | 2 | | | mA | output source current; on pins SDIO, CLK; VOH = 4.6 V; VDD = 5 V | 30 |
| Leakage current after ESD event | IL | -500 | | 500 | nA | after ESD event | 30 |
| Output voltage variation | ΔVo | -100 | | 100 | mV | VLCD = 5 V | 30 |
| Output resistance | Ro | | 1.5 | 3 | kΩ | VLCD = 5 V; outputs measured one at a time | 31 |
| Frame frequency ffr | ffr | 42 | 64 | 86 | Hz | FF[2:0] = 001 | 33 |
| External clock frequency | fclk(ext) | | | 4096 | Hz | | 33 |
| HIGH-level clock time | tclk(H) | 60 | | | μs | external clock | 33 |
| LOW-level clock time | tclk(L) | 60 | | | μs | external clock | 33 |
| Reset pulse width | tw(rst) | 10 | | | μs | reset pulse width on pin RST | 33 |
| SCL clock frequency (SPI-bus) | fSCL | | | 5 | MHz | | 35 |
| LOW period of the SCL clock (SPI-bus) | tLOW | 150 | | | ns | | 35 |
| HIGH period of the SCL clock (SPI-bus) | tHIGH | 80 | | | ns | | 35 |
| Rise time (SPI-bus) | tr | | | 100 | ns | | 35 |
| Fall time (SPI-bus) | tf | | | 100 | ns | | 35 |
| CE_N set-up time | tsu(CE_N) | 30 | | | ns | | 36 |
| CE_N hold time | th(CE_N) | 10 | | | ns | | 36 |
| CE_N recovery time | trec(CE_N) | 70 | | | ns | | 36 |
| SDIO set-up time write data | tsu | 5 | | | ns | write data | 36 |
| SDIO hold time write data | th | 50 | | | ns | write data | 36 |
| SDIO read delay time | td(R)SDIO | | | 150 | ns | CL = 50 pF | 36 |
| SDIO disable time | tdis(SDIO) | | | 50 | ns | no load | 36 |
| Transition time from SDI to SDO | tt(SDI-SDO) | 0 | | | ns | write to read mode | 36 |
## CAD (KiCad official)
- Symbol: `PCA8561BHN`
- Footprint: `Package_DFN_QFN:HVQFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm`
- 3D model: HVQFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files: `pca8561bhn-ay-etched.step` / `pca8561bhn-ay-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `pca8561bhn-ay.step` / `pca8561bhn-ay.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [NXP Semicon datasheet](https://www.nxp.com/docs/en/data-sheet/PCA8561BHN.pdf) (50 pp, sha256 `49517ebdf09b65e8`, retrieved 2026-11-20)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/pca8561bhn-ay-datasheet.pdf)