← Commit history

Publish 0.1.2

Ray ·82ef3fbc81 · ·parent 4d67b6c
5 files changed +715−182
README.md+76−74
@@ -2,44 +2,44 @@  **NXP Semicon** · LCD Drivers · HVQFN-32-EP(5x5) -PCA8561BHN from NXP Semicon, in a HVQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.+PCA8561BHN from NXP Semicon, in a HVQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.  ## Pinout  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | COM3 | output | LCD backplane output COM3, used in 1:4 multiplex mode and must be directly connected to the LCD; left open-circuit if unused. |-| 2 | VLCD | power_in | LCD supply voltage, specified at 1.8 V to 5.5 V and must never be asserted before VDD. |-| 3 | VDD | power_in | Supply voltage, specified at 1.8 V to 5.5 V. |+| 1 | COM3 | output | LCD backplane output that must be directly connected to the LCD; in 1:3 multiplex mode it carries the same signal as COM1 and may be tied to it. |+| 2 | VLCD | power_in | LCD supply voltage, specified 1.8 V to 5.5 V; VLCD must never be asserted before VDD and must never be connected while VDD is switched off. |+| 3 | VDD | power_in | Supply voltage, specified 1.8 V to 5.5 V, with a decoupling capacitor of at least 100 nF recommended. | | 4 | VSS | power_in | Ground supply; the die paddle (exposed pad) is connected to VSS and should be electrically isolated. |-| 5 | RST | input | Reset input, active LOW; holding it low for at least 10 µs resets the device when the internal POR is disabled. |-| 6 | SDIO | bidirectional | SPI-bus serial data input/output (PCA8561B); input data are sampled on the rising edge of SCL and output data are valid after the falling edge of SCL. |+| 5 | RST | input | Reset input, active LOW; when the internal POR is disabled the chip must be reset by holding RST at logic 0 for at least 10 µs. |+| 6 | SDIO | bidirectional | SPI-bus serial data input/output; input data are sampled on the rising edge of SCL and output data are valid after the falling edge of SCL. | | 7 | CLK | bidirectional | Internal oscillator output or external oscillator input; must be left open if unused. |-| 8 | SCL | input | Serial clock input for the SPI-bus; input may be higher than VDD, and the maximum SPI clock is 5 MHz. |-| 9 | CE | input | SPI-bus chip enable input, active LOW; must not be wired permanently LOW. |-| 10 | PORE | input | Power-On Reset enable: connect to VDD to enable the internal POR, or to VSS (or leave open) to disable it. |-| 11 | n.c. | unconnected | Not connected in the PCA8561BHN (SPI-bus version). |-| 12 | SEG0 | output | LCD segment output SEG0, must be directly connected to the LCD; left open-circuit if unused. |-| 13 | SEG1 | output | LCD segment output SEG1, must be directly connected to the LCD; left open-circuit if unused. |-| 14 | SEG2 | output | LCD segment output SEG2, must be directly connected to the LCD; left open-circuit if unused. |-| 15 | SEG3 | output | LCD segment output SEG3, must be directly connected to the LCD; left open-circuit if unused. |-| 16 | SEG4 | output | LCD segment output SEG4, must be directly connected to the LCD; left open-circuit if unused. |-| 17 | SEG5 | output | LCD segment output SEG5, must be directly connected to the LCD; left open-circuit if unused. |-| 18 | SEG6 | output | LCD segment output SEG6, must be directly connected to the LCD; left open-circuit if unused. |-| 19 | SEG7 | output | LCD segment output SEG7, must be directly connected to the LCD; left open-circuit if unused. |-| 20 | SEG8 | output | LCD segment output SEG8, must be directly connected to the LCD; left open-circuit if unused. |-| 21 | SEG9 | output | LCD segment output SEG9, must be directly connected to the LCD; left open-circuit if unused. |-| 22 | SEG10 | output | LCD segment output SEG10, must be directly connected to the LCD; left open-circuit if unused. |-| 23 | SEG11 | output | LCD segment output SEG11, must be directly connected to the LCD; left open-circuit if unused. |-| 24 | SEG12 | output | LCD segment output SEG12, must be directly connected to the LCD; left open-circuit if unused. |-| 25 | SEG13 | output | LCD segment output SEG13, must be directly connected to the LCD; left open-circuit if unused. |-| 26 | SEG14 | output | LCD segment output SEG14, must be directly connected to the LCD; left open-circuit if unused. |-| 27 | SEG15 | output | LCD segment output SEG15, must be directly connected to the LCD; left open-circuit if unused. |-| 28 | SEG16 | output | LCD segment output SEG16, must be directly connected to the LCD; left open-circuit if unused. |-| 29 | SEG17 | output | LCD segment output SEG17, must be directly connected to the LCD; left open-circuit if unused. |-| 30 | COM0 | output | LCD backplane output COM0, must be directly connected to the LCD; left open-circuit if unused. |-| 31 | COM1 | output | LCD backplane output COM1, must be directly connected to the LCD; left open-circuit if unused. |-| 32 | COM2 | output | LCD backplane output COM2, must be directly connected to the LCD; left open-circuit if unused. |+| 8 | SCL | input | Serial clock input for the SPI-bus; the input may be higher than VDD. |+| 9 | CE | input | Chip enable input, active LOW; the SPI interface is reset while CE is HIGH, and CE must not be wired permanently LOW. |+| 10 | PORE | input | Power-On Reset enable: connect to VDD to enable the internal POR, or connect to VSS (or leave open) to disable it; series resistance between VDD and this pin must not exceed 1 kΩ. |+| 11 | n.c. | unconnected | Not connected. |+| 12 | SEG0 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 13 | SEG1 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 14 | SEG2 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 15 | SEG3 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 16 | SEG4 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 17 | SEG5 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 18 | SEG6 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 19 | SEG7 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 20 | SEG8 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 21 | SEG9 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 22 | SEG10 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 23 | SEG11 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 24 | SEG12 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 25 | SEG13 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 26 | SEG14 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 27 | SEG15 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 28 | SEG16 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 29 | SEG17 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |+| 30 | COM0 | output | LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode. |+| 31 | COM1 | output | LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode. |+| 32 | COM2 | output | LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode. | | 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |  ## Key specifications@@ -57,65 +57,67 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  | Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page | |---|---|---|---|---|---|---|---|-| VDD supply voltage | VDD | 1.8 |  | 5.5 | V |  | 30 |+| Limiting values: supply voltage VDD | VDD | -0.5 |  | 6.5 | V |  | 29 |+| Limiting values: LCD supply voltage | VLCD | -0.5 |  | 6.5 | V |  | 29 |+| Limiting values: input voltage | VI | -0.5 |  | 6.5 | V |  | 29 |+| Limiting values: output voltage | VO | -0.5 |  | 6.5 | V |  | 29 |+| Limiting values: input current | II | -10 |  | 10 | mA |  | 29 |+| Limiting values: output current | IO | -10 |  | 10 | mA |  | 29 |+| Limiting values: supply current | IDD | -50 |  | 50 | mA |  | 29 |+| Limiting values: LCD supply current | IDD(LCD) | -50 |  | 50 | mA |  | 29 |+| Limiting values: ground supply current | ISS | -50 |  | 50 | mA |  | 29 |+| Limiting values: total power dissipation | Ptot |  |  | 100 | mW |  | 29 |+| Limiting values: output power | Po |  |  | 100 | mW |  | 29 |+| Limiting values: ESD HBM voltage | VESD | -2000 |  | 2000 | V | HBM, on pins SCL, SDA, CE; pass level | 29 |+| Limiting values: ESD HBM voltage | VESD | -3500 |  | 3500 | V | HBM, on all other pins; pass level | 29 |+| Limiting values: ESD CDM voltage | VESD | -2000 |  | 2000 | V | CDM; pass level | 29 |+| Limiting values: latch-up current | Ilu |  |  | 200 | mA | latch-up test at maximum ambient temperature; pass level | 29 |+| Limiting values: storage temperature | Tstg | -55 |  | 150 | °C |  | 29 |+| Limiting values: ambient temperature operating device | Tamb | -40 |  | 105 | °C | operating device | 29 |+| Supply voltage VDD | VDD | 1.8 |  | 5.5 | V |  | 30 | | LCD supply voltage | VLCD | 1.8 |  | 5.5 | V |  | 30 |-| supply current | IDD |  | 1.8 | 3 | μA | ffr = 64 Hz; no bus activity; VDD = 5.5 V; Tamb = 105 °C | 30 |-| LCD supply current | IDD(LCD) |  | 3.7 | 4.7 | μA | ffr = 64 Hz; no bus activity; VLCD = 5.5 V; Tamb = 105 °C; BOOST = 0; no display load | 30 |-| LOW-level output current on pin CLK | IOL | 2 |  |  | mA | output sink current; VOL = 0.4 V; VDD = 5 V | 30 |-| LOW-level output current on pin SDIO | IOL | 2 |  |  | mA | output sink current; VOL = 0.4 V; VDD = 5 V | 30 |-| HIGH-level output current on pins SDIO, CLK | IOH | 2 |  |  | mA | output source current; VOH = 4.6 V; VDD = 5 V | 30 |-| leakage current after ESD event | IL | -500 |  | 500 | nA | after ESD event | 30 |-| output voltage variation | ΔVo | -100 |  | 100 | mV | VLCD = 5 V | 30 |-| output resistance | Ro |  | 1.5 | 3 | kΩ | VLCD = 5 V; outputs measured one at a time | 31 |-| frame frequency FF[2:0] = 001 | ffr | 42 | 64 | 86 | Hz | FF[2:0] = 001 | 33 |-| external clock frequency | fclk(ext) |  |  | 4096 | Hz |  | 33 |-| HIGH-level clock time external clock | tclk(H) | 60 |  |  | μs | external clock | 33 |-| LOW-level clock time external clock | tclk(L) | 60 |  |  | μs | external clock | 33 |-| reset pulse width on pin RST | tw(rst) | 10 |  |  | μs |  | 33 |-| SCL clock frequency | fSCL |  |  | 5 | MHz |  | 35 |-| LOW period of the SCL clock | tLOW | 150 |  |  | ns |  | 35 |-| HIGH period of the SCL clock | tHIGH | 80 |  |  | ns |  | 35 |-| rise time | tr |  |  | 100 | ns |  | 35 |-| fall time | tf |  |  | 100 | ns |  | 35 |+| Ambient temperature range (operating) | Tamb | -40 |  | 105 | °C | unless otherwise specified (Characteristics header) | 30 |+| Supply current IDD | IDD |  | 1.8 | 3 | μA | ffr = 64 Hz; no bus activity; VDD = 5.5 V; Tamb = 105 °C | 30 |+| LCD supply current IDD(LCD) | IDD(LCD) |  | 3.7 | 4.7 | μA | ffr = 64 Hz; no bus activity; VLCD = 5.5 V; Tamb = 105 °C; BOOST = 0; no display load | 30 |+| LOW-level output sink current on pin CLK | IOL | 2 |  |  | mA | output sink current; VOL = 0.4 V; VDD = 5 V; on pin CLK | 30 |+| LOW-level output sink current on pin SDIO | IOL | 2 |  |  | mA | output sink current; VOL = 0.4 V; VDD = 5 V; on pin SDIO | 30 |+| LOW-level output sink current on pin SDA | IOL | 3 |  |  | mA | output sink current; VOL = 0.4 V; VDD = 5 V; on pin SDA | 30 |+| HIGH-level output source current | IOH | 2 |  |  | mA | output source current; on pins SDIO, CLK; VOH = 4.6 V; VDD = 5 V | 30 |+| Leakage current after ESD event | IL | -500 |  | 500 | nA | after ESD event | 30 |+| Output voltage variation | ΔVo | -100 |  | 100 | mV | VLCD = 5 V | 30 |+| Output resistance | Ro |  | 1.5 | 3 | kΩ | VLCD = 5 V; outputs measured one at a time | 31 |+| Frame frequency ffr | ffr | 42 | 64 | 86 | Hz | FF[2:0] = 001 | 33 |+| External clock frequency | fclk(ext) |  |  | 4096 | Hz |  | 33 |+| HIGH-level clock time | tclk(H) | 60 |  |  | μs | external clock | 33 |+| LOW-level clock time | tclk(L) | 60 |  |  | μs | external clock | 33 |+| Reset pulse width | tw(rst) | 10 |  |  | μs | reset pulse width on pin RST | 33 |+| SCL clock frequency (SPI-bus) | fSCL |  |  | 5 | MHz |  | 35 |+| LOW period of the SCL clock (SPI-bus) | tLOW | 150 |  |  | ns |  | 35 |+| HIGH period of the SCL clock (SPI-bus) | tHIGH | 80 |  |  | ns |  | 35 |+| Rise time (SPI-bus) | tr |  |  | 100 | ns |  | 35 |+| Fall time (SPI-bus) | tf |  |  | 100 | ns |  | 35 | | CE_N set-up time | tsu(CE_N) | 30 |  |  | ns |  | 36 | | CE_N hold time | th(CE_N) | 10 |  |  | ns |  | 36 | | CE_N recovery time | trec(CE_N) | 70 |  |  | ns |  | 36 |-| set-up time write data | tsu | 5 |  |  | ns |  | 36 |-| hold time write data | th | 50 |  |  | ns |  | 36 |+| SDIO set-up time write data | tsu | 5 |  |  | ns | write data | 36 |+| SDIO hold time write data | th | 50 |  |  | ns | write data | 36 | | SDIO read delay time | td(R)SDIO |  |  | 150 | ns | CL = 50 pF | 36 | | SDIO disable time | tdis(SDIO) |  |  | 50 | ns | no load | 36 |-| transition time from SDI to SDO | tt(SDI-SDO) | 0 |  |  | ns | write to read mode | 36 |-| VDD supply voltage | VDD | -0.5 |  | 6.5 | V |  | 29 |-| VLCD LCD supply voltage | VLCD | -0.5 |  | 6.5 | V |  | 29 |-| input voltage | VI | -0.5 |  | 6.5 | V |  | 29 |-| output voltage | VO | -0.5 |  | 6.5 | V |  | 29 |-| input current | II | -10 |  | 10 | mA |  | 29 |-| output current | IO | -10 |  | 10 | mA |  | 29 |-| supply current | IDD | -50 |  | 50 | mA |  | 29 |-| LCD supply current | IDD(LCD) | -50 |  | 50 | mA |  | 29 |-| ground supply current | ISS | -50 |  | 50 | mA |  | 29 |-| total power dissipation | Ptot |  |  | 100 | mW |  | 29 |-| output power | Po |  |  | 100 | mW |  | 29 |-| electrostatic discharge voltage HBM | VESD | -2000 |  | 2000 | V | HBM; on pins SCL, SDA, CE | 29 |-| electrostatic discharge voltage HBM | VESD | -3500 |  | 3500 | V | HBM; on all other pins | 29 |-| electrostatic discharge voltage CDM | VESD | -2000 |  | 2000 | V | CDM | 29 |-| latch-up current | Ilu |  |  | 200 | mA |  | 29 |-| storage temperature | Tstg | -55 |  | 150 | °C |  | 29 |-| ambient temperature operating device | Tamb | -40 |  | 105 | °C |  | 29 |+| Transition time from SDI to SDO | tt(SDI-SDO) | 0 |  |  | ns | write to read mode | 36 | -## CAD (land: KiCad; 3D: generated from the datasheet)+## CAD (KiCad official)  - Symbol: `PCA8561BHN` - Footprint: `Package_DFN_QFN:HVQFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm`-- 3D model: HVQFN-32-EP(5x5), generated on the KiCad land (body 5 x 5 mm, terminals on the pads, 0.85 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)+- 3D model: HVQFN-32-EP(5x5) (KiCad packages3D, STEP) - 3D model files: `pca8561bhn-ay-etched.step` / `pca8561bhn-ay-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `pca8561bhn-ay.step` / `pca8561bhn-ay.glb` are the bare package body.  ## Provenance  Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [NXP Semicon datasheet](https://www.nxp.com/docs/en/data-sheet/PCA8561BHN.pdf) (50 pp, sha256 `49517ebdf09b65e8`, retrieved 2026-11-13, tier: manufacturer)+- **Datasheet:** [NXP Semicon datasheet](https://www.nxp.com/docs/en/data-sheet/PCA8561BHN.pdf) (50 pp, sha256 `49517ebdf09b65e8`, retrieved 2026-11-20) - **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.-- **CAD:** land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).  [Datasheet PDF](docs/pca8561bhn-ay-datasheet.pdf)
package.json+591−49
@@ -1,6 +1,6 @@ {   "slug": "pca8561bhn-ay",-  "version": "0.1.1",+  "version": "0.1.2",   "type": "component",   "description": "NXP Semicon LCD Drivers, HVQFN-32-EP(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",   "tags": [@@ -53,7 +53,7 @@       "mouser": "771-PCA8561BHN/AY"     },     "distributor_check": {-      "checked_at": "2026-11-13T02:42:27Z",+      "checked_at": "2026-11-20T07:16:50Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": "568-13033-2-ND",@@ -70,19 +70,19 @@         "number": "1",         "name": "COM3",         "type": "output",-        "description": "LCD backplane output COM3, used in 1:4 multiplex mode and must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD backplane output that must be directly connected to the LCD; in 1:3 multiplex mode it carries the same signal as COM1 and may be tied to it."       },       {         "number": "2",         "name": "VLCD",         "type": "power_in",-        "description": "LCD supply voltage, specified at 1.8 V to 5.5 V and must never be asserted before VDD."+        "description": "LCD supply voltage, specified 1.8 V to 5.5 V; VLCD must never be asserted before VDD and must never be connected while VDD is switched off."       },       {         "number": "3",         "name": "VDD",         "type": "power_in",-        "description": "Supply voltage, specified at 1.8 V to 5.5 V."+        "description": "Supply voltage, specified 1.8 V to 5.5 V, with a decoupling capacitor of at least 100 nF recommended."       },       {         "number": "4",@@ -94,13 +94,13 @@         "number": "5",         "name": "RST",         "type": "input",-        "description": "Reset input, active LOW; holding it low for at least 10 µs resets the device when the internal POR is disabled."+        "description": "Reset input, active LOW; when the internal POR is disabled the chip must be reset by holding RST at logic 0 for at least 10 µs."       },       {         "number": "6",         "name": "SDIO",         "type": "bidirectional",-        "description": "SPI-bus serial data input/output (PCA8561B); input data are sampled on the rising edge of SCL and output data are valid after the falling edge of SCL."+        "description": "SPI-bus serial data input/output; input data are sampled on the rising edge of SCL and output data are valid after the falling edge of SCL."       },       {         "number": "7",@@ -112,151 +112,151 @@         "number": "8",         "name": "SCL",         "type": "input",-        "description": "Serial clock input for the SPI-bus; input may be higher than VDD, and the maximum SPI clock is 5 MHz."+        "description": "Serial clock input for the SPI-bus; the input may be higher than VDD."       },       {         "number": "9",         "name": "CE",         "type": "input",-        "description": "SPI-bus chip enable input, active LOW; must not be wired permanently LOW."+        "description": "Chip enable input, active LOW; the SPI interface is reset while CE is HIGH, and CE must not be wired permanently LOW."       },       {         "number": "10",         "name": "PORE",         "type": "input",-        "description": "Power-On Reset enable: connect to VDD to enable the internal POR, or to VSS (or leave open) to disable it."+        "description": "Power-On Reset enable: connect to VDD to enable the internal POR, or connect to VSS (or leave open) to disable it; series resistance between VDD and this pin must not exceed 1 kΩ."       },       {         "number": "11",         "name": "n.c.",         "type": "unconnected",-        "description": "Not connected in the PCA8561BHN (SPI-bus version)."+        "description": "Not connected."       },       {         "number": "12",         "name": "SEG0",         "type": "output",-        "description": "LCD segment output SEG0, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "13",         "name": "SEG1",         "type": "output",-        "description": "LCD segment output SEG1, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "14",         "name": "SEG2",         "type": "output",-        "description": "LCD segment output SEG2, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "15",         "name": "SEG3",         "type": "output",-        "description": "LCD segment output SEG3, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "16",         "name": "SEG4",         "type": "output",-        "description": "LCD segment output SEG4, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "17",         "name": "SEG5",         "type": "output",-        "description": "LCD segment output SEG5, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "18",         "name": "SEG6",         "type": "output",-        "description": "LCD segment output SEG6, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "19",         "name": "SEG7",         "type": "output",-        "description": "LCD segment output SEG7, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "20",         "name": "SEG8",         "type": "output",-        "description": "LCD segment output SEG8, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "21",         "name": "SEG9",         "type": "output",-        "description": "LCD segment output SEG9, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "22",         "name": "SEG10",         "type": "output",-        "description": "LCD segment output SEG10, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "23",         "name": "SEG11",         "type": "output",-        "description": "LCD segment output SEG11, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "24",         "name": "SEG12",         "type": "output",-        "description": "LCD segment output SEG12, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "25",         "name": "SEG13",         "type": "output",-        "description": "LCD segment output SEG13, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "26",         "name": "SEG14",         "type": "output",-        "description": "LCD segment output SEG14, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "27",         "name": "SEG15",         "type": "output",-        "description": "LCD segment output SEG15, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "28",         "name": "SEG16",         "type": "output",-        "description": "LCD segment output SEG16, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "29",         "name": "SEG17",         "type": "output",-        "description": "LCD segment output SEG17, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "30",         "name": "COM0",         "type": "output",-        "description": "LCD backplane output COM0, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode."       },       {         "number": "31",         "name": "COM1",         "type": "output",-        "description": "LCD backplane output COM1, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode."       },       {         "number": "32",         "name": "COM2",         "type": "output",-        "description": "LCD backplane output COM2, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode."       },       {         "number": "33",@@ -276,27 +276,21 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: The exposed die paddle (exposed pad) of the HVQFN32 package is not given a number on the pinout figu; Pin 6 and pin 9 are shown with different names depending on bus type. The PCA8561BHN (SPI-bus) pinou; Pin 11 is n.c. (not connected) in the SPI variant; on the I2C variant it is A1. Only the SPI-variant",+          "extractor flagged: The HVQFN32 exposed die paddle (thermal pad) is not a numbered terminal and is not listed in the pin; Pin layout was taken from the PCA8561BHN (SPI-bus) variant, Figure 4 and Table 3 column PCA8561BHN. ",           "exposed pad 33 added from the footprint"         ],         "pages_sent": 50,-        "cost_usd": 0.0337,-        "at": "2026-11-13T02:42:14"+        "cost_usd": 0.1954,+        "at": "2026-11-20T07:16:41"       },       "datasheet": {         "url": "https://www.nxp.com/docs/en/data-sheet/PCA8561BHN.pdf",         "pages": 50,         "sha256": "49517ebdf09b65e8",-        "source_tier": "mfr"-      },-      "cad": "land: KiCad official (CC-BY-SA 4.0); 3D: generated from the datasheet",-      "model_3d_generated": {-        "generator": "factory/gen_pkg3d.py",-        "family": "VQFN",-        "height_mm": 0.85,-        "height_basis": "datasheet A, max",-        "standoff_mm": 0.0+        "source_tier": "mfr",+        "citation": "NXP Semicon datasheet"       },+      "cad": "KiCad official (CC-BY-SA 4.0)",       "pins": {         "total": 33,         "described": 33,@@ -324,8 +318,8 @@         "zmin_mm": 0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "c2077b952f3e1f0e1330e4b436b88a6f2e4f9da343b1a17ebf2b8d00d0855ec5",-        "checked": "2026-11-13",+        "sha256": "4343e108ffb8a76eac12faee67b9cd22391168776552297f7718231a2905cdce",+        "checked": "2026-11-20",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -343,13 +337,13 @@         "zmin_mm": 0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "89d905795bdcb7acadec3fd3b5b7e85050149e720593a4deea0aa5fad70c56be",-        "checked": "2026-11-13",+        "sha256": "ac3a4b5d48ad2c4e60281b44b8b4aadf7a67f98404ec7e3bfe80bce37003edcf",+        "checked": "2026-11-20",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ],     "package_dims": {-      "package_code": "SOT617-3 (HVQFN32)",+      "package_code": "HVQFN32 (SOT617-3)",       "source_page": 38,       "D": {         "nom_mm": 5.0,@@ -389,5 +383,553 @@         "by": "factory/package_fit.py"       }     }+  },+  "metadata": {+    "characteristics": {+      "version": 1,+      "source": "datasheet",+      "rows": [+        {+          "name": "VDD supply voltage",+          "symbol": "VDD",+          "kind": "recommended_operating",+          "unit": "V",+          "min": 1.8,+          "typ": null,+          "max": 5.5,+          "conditions": "",+          "source_page": 30,+          "source": "datasheet"+        },+        {+          "name": "LCD supply voltage",+          "symbol": "VLCD",+          "kind": "recommended_operating",+          "unit": "V",+          "min": 1.8,+          "typ": null,+          "max": 5.5,+          "conditions": "",+          "source_page": 30,+          "source": "datasheet"+        },+        {+          "name": "supply current",+          "symbol": "IDD",+          "kind": "electrical",+          "unit": "μA",+          "min": null,+          "typ": 1.8,+          "max": 3,+          "conditions": "ffr = 64 Hz; no bus activity; VDD = 5.5 V; Tamb = 105 °C",+          "source_page": 30,+          "source": "datasheet"+        },+        {+          "name": "LCD supply current",+          "symbol": "IDD(LCD)",+          "kind": "electrical",+          "unit": "μA",+          "min": null,+          "typ": 3.7,+          "max": 4.7,+          "conditions": "ffr = 64 Hz; no bus activity; VLCD = 5.5 V; Tamb = 105 °C; BOOST = 0; no display load",+          "source_page": 30,+          "source": "datasheet"+        },+        {+          "name": "LOW-level output current on pin CLK",+          "symbol": "IOL",+          "kind": "electrical",+          "unit": "mA",+          "min": 2,+          "typ": null,+          "max": null,+          "conditions": "output sink current; VOL = 0.4 V; VDD = 5 V",+          "source_page": 30,+          "source": "datasheet"+        },+        {+          "name": "LOW-level output current on pin SDIO",+          "symbol": "IOL",+          "kind": "electrical",+          "unit": "mA",+          "min": 2,+          "typ": null,+          "max": null,+          "conditions": "output sink current; VOL = 0.4 V; VDD = 5 V",+          "source_page": 30,+          "source": "datasheet"+        },+        {+          "name": "HIGH-level output current on pins SDIO, CLK",+          "symbol": "IOH",+          "kind": "electrical",+          "unit": "mA",+          "min": 2,+          "typ": null,+          "max": null,+          "conditions": "output source current; VOH = 4.6 V; VDD = 5 V",+          "source_page": 30,+          "source": "datasheet"+        },+        {+          "name": "leakage current after ESD event",+          "symbol": "IL",+          "kind": "electrical",+          "unit": "nA",+          "min": -500,+          "typ": null,+          "max": 500,+          "conditions": "after ESD event",+          "source_page": 30,+          "source": "datasheet"+        },+        {+          "name": "output voltage variation",+          "symbol": "ΔVo",+          "kind": "electrical",+          "unit": "mV",+          "min": -100,+          "typ": null,+          "max": 100,+          "conditions": "VLCD = 5 V",+          "source_page": 30,+          "source": "datasheet"+        },+        {+          "name": "output resistance",+          "symbol": "Ro",+          "kind": "electrical",+          "unit": "kΩ",+          "min": null,+          "typ": 1.5,+          "max": 3,+          "conditions": "VLCD = 5 V; outputs measured one at a time",+          "source_page": 31,+          "source": "datasheet"+        },+        {+          "name": "frame frequency FF[2:0] = 001",+          "symbol": "ffr",+          "kind": "electrical",+          "unit": "Hz",+          "min": 42,+          "typ": 64,+          "max": 86,+          "conditions": "FF[2:0] = 001",+          "source_page": 33,+          "source": "datasheet"+        },+        {+          "name": "external clock frequency",+          "symbol": "fclk(ext)",+          "kind": "timing",+          "unit": "Hz",+          "min": null,+          "typ": null,+          "max": 4096,+          "conditions": "",+          "source_page": 33,+          "source": "datasheet"+        },+        {+          "name": "HIGH-level clock time external clock",+          "symbol": "tclk(H)",+          "kind": "timing",+          "unit": "μs",+          "min": 60,+          "typ": null,+          "max": null,+          "conditions": "external clock",+          "source_page": 33,+          "source": "datasheet"+        },+        {+          "name": "LOW-level clock time external clock",+          "symbol": "tclk(L)",+          "kind": "timing",+          "unit": "μs",+          "min": 60,+          "typ": null,+          "max": null,+          "conditions": "external clock",+          "source_page": 33,+          "source": "datasheet"+        },+        {+          "name": "reset pulse width on pin RST",+          "symbol": "tw(rst)",+          "kind": "timing",+          "unit": "μs",+          "min": 10,+          "typ": null,+          "max": null,+          "conditions": "",+          "source_page": 33,+          "source": "datasheet"+        },+        {+          "name": "SCL clock frequency",+          "symbol": "fSCL",+          "kind": "timing",+          "unit": "MHz",+          "min": null,+          "typ": null,+          "max": 5,+          "conditions": "",+          "source_page": 35,+          "source": "datasheet"+        },+        {+          "name": "LOW period of the SCL clock",+          "symbol": "tLOW",+          "kind": "timing",+          "unit": "ns",+          "min": 150,+          "typ": null,+          "max": null,+          "conditions": "",+          "source_page": 35,+          "source": "datasheet"+        },+        {+          "name": "HIGH period of the SCL clock",+          "symbol": "tHIGH",+          "kind": "timing",+          "unit": "ns",+          "min": 80,+          "typ": null,+          "max": null,+          "conditions": "",+          "source_page": 35,+          "source": "datasheet"+        },+        {+          "name": "rise time",+          "symbol": "tr",+          "kind": "timing",+          "unit": "ns",+          "min": null,+          "typ": null,+          "max": 100,+          "conditions": "",+          "source_page": 35,+          "source": "datasheet"+        },+        {+          "name": "fall time",+          "symbol": "tf",+          "kind": "timing",+          "unit": "ns",+          "min": null,+          "typ": null,+          "max": 100,+          "conditions": "",+          "source_page": 35,+          "source": "datasheet"+        },+        {+          "name": "CE_N set-up time",+          "symbol": "tsu(CE_N)",+          "kind": "timing",+          "unit": "ns",+          "min": 30,+          "typ": null,+          "max": null,+          "conditions": "",+          "source_page": 36,+          "source": "datasheet"+        },+        {+          "name": "CE_N hold time",+          "symbol": "th(CE_N)",+          "kind": "timing",+          "unit": "ns",+          "min": 10,+          "typ": null,+          "max": null,+          "conditions": "",+          "source_page": 36,+          "source": "datasheet"+        },+        {+          "name": "CE_N recovery time",+          "symbol": "trec(CE_N)",+          "kind": "timing",+          "unit": "ns",+          "min": 70,+          "typ": null,+          "max": null,+          "conditions": "",+          "source_page": 36,+          "source": "datasheet"+        },+        {+          "name": "set-up time write data",+          "symbol": "tsu",+          "kind": "timing",+          "unit": "ns",+          "min": 5,+          "typ": null,+          "max": null,+          "conditions": "",+          "source_page": 36,+          "source": "datasheet"+        },+        {+          "name": "hold time write data",+          "symbol": "th",+          "kind": "timing",+          "unit": "ns",+          "min": 50,+          "typ": null,+          "max": null,+          "conditions": "",+          "source_page": 36,+          "source": "datasheet"+        },+        {+          "name": "SDIO read delay time",+          "symbol": "td(R)SDIO",+          "kind": "timing",+          "unit": "ns",+          "min": null,+          "typ": null,+          "max": 150,+          "conditions": "CL = 50 pF",+          "source_page": 36,+          "source": "datasheet"+        },+        {+          "name": "SDIO disable time",+          "symbol": "tdis(SDIO)",+          "kind": "timing",+          "unit": "ns",+          "min": null,+          "typ": null,+          "max": 50,+          "conditions": "no load",+          "source_page": 36,+          "source": "datasheet"+        },+        {+          "name": "transition time from SDI to SDO",+          "symbol": "tt(SDI-SDO)",+          "kind": "timing",+          "unit": "ns",+          "min": 0,+          "typ": null,+          "max": null,+          "conditions": "write to read mode",+          "source_page": 36,+          "source": "datasheet"+        },+        {+          "name": "VDD supply voltage",+          "symbol": "VDD",+          "kind": "absolute_maximum",+          "unit": "V",+          "min": -0.5,+          "typ": null,+          "max": 6.5,+          "conditions": "",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "VLCD LCD supply voltage",+          "symbol": "VLCD",+          "kind": "absolute_maximum",+          "unit": "V",+          "min": -0.5,+          "typ": null,+          "max": 6.5,+          "conditions": "",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "input voltage",+          "symbol": "VI",+          "kind": "absolute_maximum",+          "unit": "V",+          "min": -0.5,+          "typ": null,+          "max": 6.5,+          "conditions": "",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "output voltage",+          "symbol": "VO",+          "kind": "absolute_maximum",+          "unit": "V",+          "min": -0.5,+          "typ": null,+          "max": 6.5,+          "conditions": "",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "input current",+          "symbol": "II",+          "kind": "absolute_maximum",+          "unit": "mA",+          "min": -10,+          "typ": null,+          "max": 10,+          "conditions": "",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "output current",+          "symbol": "IO",+          "kind": "absolute_maximum",+          "unit": "mA",+          "min": -10,+          "typ": null,+          "max": 10,+          "conditions": "",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "supply current",+          "symbol": "IDD",+          "kind": "absolute_maximum",+          "unit": "mA",+          "min": -50,+          "typ": null,+          "max": 50,+          "conditions": "",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "LCD supply current",+          "symbol": "IDD(LCD)",+          "kind": "absolute_maximum",+          "unit": "mA",+          "min": -50,+          "typ": null,+          "max": 50,+          "conditions": "",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "ground supply current",+          "symbol": "ISS",+          "kind": "absolute_maximum",+          "unit": "mA",+          "min": -50,+          "typ": null,+          "max": 50,+          "conditions": "",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "total power dissipation",+          "symbol": "Ptot",+          "kind": "absolute_maximum",+          "unit": "mW",+          "min": null,+          "typ": null,+          "max": 100,+          "conditions": "",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "output power",+          "symbol": "Po",+          "kind": "absolute_maximum",+          "unit": "mW",+          "min": null,+          "typ": null,+          "max": 100,+          "conditions": "",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "electrostatic discharge voltage HBM",+          "symbol": "VESD",+          "kind": "absolute_maximum",+          "unit": "V",+          "min": -2000,+          "typ": null,+          "max": 2000,+          "conditions": "HBM; on pins SCL, SDA, CE",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "electrostatic discharge voltage HBM",+          "symbol": "VESD",+          "kind": "absolute_maximum",+          "unit": "V",+          "min": -3500,+          "typ": null,+          "max": 3500,+          "conditions": "HBM; on all other pins",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "electrostatic discharge voltage CDM",+          "symbol": "VESD",+          "kind": "absolute_maximum",+          "unit": "V",+          "min": -2000,+          "typ": null,+          "max": 2000,+          "conditions": "CDM",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "latch-up current",+          "symbol": "Ilu",+          "kind": "absolute_maximum",+          "unit": "mA",+          "min": null,+          "typ": null,+          "max": 200,+          "conditions": "",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "storage temperature",+          "symbol": "Tstg",+          "kind": "absolute_maximum",+          "unit": "°C",+          "min": -55,+          "typ": null,+          "max": 150,+          "conditions": "",+          "source_page": 29,+          "source": "datasheet"+        },+        {+          "name": "ambient temperature operating device",+          "symbol": "Tamb",+          "kind": "absolute_maximum",+          "unit": "°C",+          "min": -40,+          "typ": null,+          "max": 105,+          "conditions": "",+          "source_page": 29,+          "source": "datasheet"+        }+      ]+    }   } }
page.json+46−57
@@ -4,7 +4,7 @@   "slug": "pca8561bhn-ay",   "title": "PCA8561BHN/AY",   "brief": "NXP Semicon LCD Drivers, HVQFN-32-EP(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.1.1",+  "version": "0.1.2",   "license": "CC-BY-SA-4.0",   "tags": [     "component",@@ -36,7 +36,7 @@       "mouser": "771-PCA8561BHN/AY"     },     "distributor_check": {-      "checked_at": "2026-11-13T02:42:27Z",+      "checked_at": "2026-11-20T07:16:50Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": "568-13033-2-ND",@@ -53,19 +53,19 @@         "number": "1",         "name": "COM3",         "type": "output",-        "description": "LCD backplane output COM3, used in 1:4 multiplex mode and must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD backplane output that must be directly connected to the LCD; in 1:3 multiplex mode it carries the same signal as COM1 and may be tied to it."       },       {         "number": "2",         "name": "VLCD",         "type": "power_in",-        "description": "LCD supply voltage, specified at 1.8 V to 5.5 V and must never be asserted before VDD."+        "description": "LCD supply voltage, specified 1.8 V to 5.5 V; VLCD must never be asserted before VDD and must never be connected while VDD is switched off."       },       {         "number": "3",         "name": "VDD",         "type": "power_in",-        "description": "Supply voltage, specified at 1.8 V to 5.5 V."+        "description": "Supply voltage, specified 1.8 V to 5.5 V, with a decoupling capacitor of at least 100 nF recommended."       },       {         "number": "4",@@ -77,13 +77,13 @@         "number": "5",         "name": "RST",         "type": "input",-        "description": "Reset input, active LOW; holding it low for at least 10 µs resets the device when the internal POR is disabled."+        "description": "Reset input, active LOW; when the internal POR is disabled the chip must be reset by holding RST at logic 0 for at least 10 µs."       },       {         "number": "6",         "name": "SDIO",         "type": "bidirectional",-        "description": "SPI-bus serial data input/output (PCA8561B); input data are sampled on the rising edge of SCL and output data are valid after the falling edge of SCL."+        "description": "SPI-bus serial data input/output; input data are sampled on the rising edge of SCL and output data are valid after the falling edge of SCL."       },       {         "number": "7",@@ -95,151 +95,151 @@         "number": "8",         "name": "SCL",         "type": "input",-        "description": "Serial clock input for the SPI-bus; input may be higher than VDD, and the maximum SPI clock is 5 MHz."+        "description": "Serial clock input for the SPI-bus; the input may be higher than VDD."       },       {         "number": "9",         "name": "CE",         "type": "input",-        "description": "SPI-bus chip enable input, active LOW; must not be wired permanently LOW."+        "description": "Chip enable input, active LOW; the SPI interface is reset while CE is HIGH, and CE must not be wired permanently LOW."       },       {         "number": "10",         "name": "PORE",         "type": "input",-        "description": "Power-On Reset enable: connect to VDD to enable the internal POR, or to VSS (or leave open) to disable it."+        "description": "Power-On Reset enable: connect to VDD to enable the internal POR, or connect to VSS (or leave open) to disable it; series resistance between VDD and this pin must not exceed 1 kΩ."       },       {         "number": "11",         "name": "n.c.",         "type": "unconnected",-        "description": "Not connected in the PCA8561BHN (SPI-bus version)."+        "description": "Not connected."       },       {         "number": "12",         "name": "SEG0",         "type": "output",-        "description": "LCD segment output SEG0, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "13",         "name": "SEG1",         "type": "output",-        "description": "LCD segment output SEG1, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "14",         "name": "SEG2",         "type": "output",-        "description": "LCD segment output SEG2, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "15",         "name": "SEG3",         "type": "output",-        "description": "LCD segment output SEG3, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "16",         "name": "SEG4",         "type": "output",-        "description": "LCD segment output SEG4, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "17",         "name": "SEG5",         "type": "output",-        "description": "LCD segment output SEG5, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "18",         "name": "SEG6",         "type": "output",-        "description": "LCD segment output SEG6, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "19",         "name": "SEG7",         "type": "output",-        "description": "LCD segment output SEG7, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "20",         "name": "SEG8",         "type": "output",-        "description": "LCD segment output SEG8, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "21",         "name": "SEG9",         "type": "output",-        "description": "LCD segment output SEG9, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "22",         "name": "SEG10",         "type": "output",-        "description": "LCD segment output SEG10, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "23",         "name": "SEG11",         "type": "output",-        "description": "LCD segment output SEG11, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "24",         "name": "SEG12",         "type": "output",-        "description": "LCD segment output SEG12, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "25",         "name": "SEG13",         "type": "output",-        "description": "LCD segment output SEG13, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "26",         "name": "SEG14",         "type": "output",-        "description": "LCD segment output SEG14, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "27",         "name": "SEG15",         "type": "output",-        "description": "LCD segment output SEG15, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "28",         "name": "SEG16",         "type": "output",-        "description": "LCD segment output SEG16, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "29",         "name": "SEG17",         "type": "output",-        "description": "LCD segment output SEG17, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."       },       {         "number": "30",         "name": "COM0",         "type": "output",-        "description": "LCD backplane output COM0, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode."       },       {         "number": "31",         "name": "COM1",         "type": "output",-        "description": "LCD backplane output COM1, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode."       },       {         "number": "32",         "name": "COM2",         "type": "output",-        "description": "LCD backplane output COM2, must be directly connected to the LCD; left open-circuit if unused."+        "description": "LCD backplane output that must be directly connected to the LCD; generated according to the selected drive mode."       },       {         "number": "33",@@ -259,27 +259,21 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: The exposed die paddle (exposed pad) of the HVQFN32 package is not given a number on the pinout figu; Pin 6 and pin 9 are shown with different names depending on bus type. The PCA8561BHN (SPI-bus) pinou; Pin 11 is n.c. (not connected) in the SPI variant; on the I2C variant it is A1. Only the SPI-variant",+          "extractor flagged: The HVQFN32 exposed die paddle (thermal pad) is not a numbered terminal and is not listed in the pin; Pin layout was taken from the PCA8561BHN (SPI-bus) variant, Figure 4 and Table 3 column PCA8561BHN. ",           "exposed pad 33 added from the footprint"         ],         "pages_sent": 50,-        "cost_usd": 0.0337,-        "at": "2026-11-13T02:42:14"+        "cost_usd": 0.1954,+        "at": "2026-11-20T07:16:41"       },       "datasheet": {         "url": "https://www.nxp.com/docs/en/data-sheet/PCA8561BHN.pdf",         "pages": 50,         "sha256": "49517ebdf09b65e8",-        "source_tier": "mfr"-      },-      "cad": "land: KiCad official (CC-BY-SA 4.0); 3D: generated from the datasheet",-      "model_3d_generated": {-        "generator": "factory/gen_pkg3d.py",-        "family": "VQFN",-        "height_mm": 0.85,-        "height_basis": "datasheet A, max",-        "standoff_mm": 0+        "source_tier": "mfr",+        "citation": "NXP Semicon datasheet"       },+      "cad": "KiCad official (CC-BY-SA 4.0)",       "pins": {         "total": 33,         "described": 33,@@ -307,8 +301,8 @@         "zmin_mm": 0,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "c2077b952f3e1f0e1330e4b436b88a6f2e4f9da343b1a17ebf2b8d00d0855ec5",-        "checked": "2026-11-13",+        "sha256": "4343e108ffb8a76eac12faee67b9cd22391168776552297f7718231a2905cdce",+        "checked": "2026-11-20",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -326,13 +320,13 @@         "zmin_mm": 0,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "89d905795bdcb7acadec3fd3b5b7e85050149e720593a4deea0aa5fad70c56be",-        "checked": "2026-11-13",+        "sha256": "ac3a4b5d48ad2c4e60281b44b8b4aadf7a67f98404ec7e3bfe80bce37003edcf",+        "checked": "2026-11-20",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ],     "package_dims": {-      "package_code": "SOT617-3 (HVQFN32)",+      "package_code": "HVQFN32 (SOT617-3)",       "source_page": 38,       "D": {         "nom_mm": 5,@@ -374,16 +368,9 @@     }   },   "metadata": {-    "specs": {-      "Manufacturer": "NXP Semicon",-      "Package": "HVQFN-32-EP(5x5)",-      "Category": "Display Modules / LED Drivers / Display Drivers",-      "Pins": "33"-    },     "characteristics": {       "version": 1,       "source": "datasheet",-      "datasheet_sha256": "49517ebdf09b65e897a6cce15114ec7fabdec48ff9f597cdbc372260b8822aad",       "rows": [         {           "name": "VDD supply voltage",@@ -966,5 +953,7 @@   ],   "visibility": {     "public": true-  }+  },+  "description": "NXP Semicon LCD Drivers, HVQFN-32-EP(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "org": "adom" }\ No newline at end of file
pca8561bhn-ay.lbr+1−1
@@ -202,7 +202,7 @@         <technology name="">           <attribute name="MPN" value="PCA8561BHN/AY" constant="no"/>           <attribute name="MANUFACTURER" value="NXP Semicon" constant="no"/>-          <attribute name="DATASHEET" value="https://www.nxp.com/docs/en/data-sheet/PCA8561.pdf" constant="no"/>+          <attribute name="DATASHEET" value="https://www.nxp.com/docs/en/data-sheet/PCA8561BHN.pdf" constant="no"/>           <attribute name="ADOM_WIKI" value="https://wiki.adom.inc/adom/pca8561bhn-ay" constant="no"/>           <attribute name="MOUSER_PN" value="771-PCA8561BHN/AY" constant="no"/>           <attribute name="DIGIKEY_PN" value="568-13033-2-ND" constant="no"/>
pca8561bhn-ay.step+1−1
@@ -1,7 +1,7 @@ ISO-10303-21; HEADER; FILE_DESCRIPTION(('Open CASCADE Model'),'2;1');-FILE_NAME('Open CASCADE Shape Model','2026-11-13T02:42:19',('Author'),(+FILE_NAME('Open CASCADE Shape Model','2026-11-19T23:38:02',('Author'),(     'Open CASCADE'),'Open CASCADE STEP processor 7.9','Open CASCADE 7.9'   ,'Unknown'); FILE_SCHEMA(('AUTOMOTIVE_DESIGN { 1 0 10303 214 1 1 1 1 }'));