main
Ray
Publish 0.1.0
f9cc3ca
PAC1952T-1E
Microchip Tech · Monitors & Reset Circuits · WLCSP-16(2.2x2.2)
PAC1952T-1E from Microchip Tech, in a WLCSP-16(2.2x2.2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| A1 | SENSE2+ | input | Analog input with a 0-FSR range for channel 2, connected to the supply side of the sense resistor; the safe operating voltage is up to 32V. |
| A2 | SENSE1- | input | Analog input with a 0-FSR range for channel 1, connected to the load side of the sense resistor; the safe operating voltage is up to 32V. |
| A3 | SENSE1+ | input | Analog input with a 0-FSR range for channel 1, connected to the supply side of the sense resistor and also used as the bus voltage input; the safe operating voltage is up to 32V. |
| A4 | VDD | power_in | Positive power supply input for the IC, 2.7V to 5.5V, to be bypassed with a 100 nF ceramic capacitor to ground near the IC. |
| B1 | SENSE2- | input | Analog input with a 0-FSR range for channel 2, connected to the load side of the sense resistor; the safe operating voltage is up to 32V. |
| B2 | GPIO/ALERT2 | bidirectional | Digital I/O that defaults to GPIO input mode and can be programmed as the open-drain ALERT2 indicator or open-drain GPIO, needing a pull-up resistor to VDD. |
| B3 | PWRDN | input | Active-low digital input that puts the device in a Power-Down state, with all circuitry including SMBus powered down. |
| B4 | GND | power_in | Ground for the IC. |
| C1 | SENSE3- | input | Inactive on PAC1952-1 in WLCSP; this pin must be grounded. |
| C2 | ADDRSEL | passive | Analog I/O pin for SMBus client address selection, with a resistor connected from this pin to ground. |
| C3 | SLOW/ALERT1 | bidirectional | Digital I/O that defaults to the SLOW input, where high forces all channels to 8 SPS, and can be programmed as the open-drain ALERT1 pin or GPIO. |
| C4 | SCL | input | SMBus/I2C clock input that needs an external pull-up resistor, except in High-Speed mode, which requires a CMOS driver from the host. |
| D1 | SENSE3+ | input | Inactive on PAC1952-1 in WLCSP; this pin must be grounded. |
| D2 | SENSE4- | input | Inactive on PAC1952-1 in WLCSP; this pin must be grounded. |
| D3 | SENSE4+ | input | Inactive on PAC1952-1 in WLCSP; this pin must be grounded. |
| D4 | SDA | bidirectional | Open-drain SMBus/I2C data I/O that requires a pull-up resistor to host VDD. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | WLCSP-16(2.2x2.2) |
| Category | Power Supply Chip |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD Pin | -0.3 | 6 | V | 5 | |||
| Voltage on SENSE- and SENSE+ Pins | -0.3 | 40 | V | 5 | |||
| Voltage on Any Other Pin to GND | -0.3 | 6 | V | 5 | |||
| Input Current to Any Pin Except VDD | -100 | 100 | mA | 5 | |||
| Operating Ambient Temperature Range | -40 | 150 | °C | 5 | |||
| Storage Temperature Range | -55 | 150 | °C | 5 | |||
| VDD Range | VDD | 2.7 | 5.5 | V | 6 | ||
| VDD Active Current | IDD | 395 | 495 | µA | 1024 SPS, 4 channels enabled | 6 | |
| VDD Active Current | IDD | 395 | 440 | µA | 1024 SPS, 4 channels enabled, TA = 0°C to +85°C | 6 | |
| VDD Active Current | IDD | 12 | 25 | µA | 8 SPS, 4 channels enabled, TA = 0°C to +85°C | 6 | |
| VDD Power-Down Current | IDD_PWRDN | 0 | 8 | µA | 6 | ||
| Bus Voltage Range | VBUS | -0.2 | 32 | V | Common-mode voltage on SENSE pins, referenced to ground | 6 | |
| VSENSE Differential Input Voltage Range | VSENSE_DIF | -100 | 100 | mV | 6 | ||
| SENSE+, SENSE- Pin Input Current | ISENSE+, ISENSE- | -6 | 0.6 | 6 | µA | VSENSE+ = VSENSE- = Full scale | 6 |
| SENSE+, SENSE- Pin Input Current | ISENSE+, ISENSE- | -1 | 0.4 | 1 | µA | VSENSE+ = 6V, VSENSE- = 5.9V | 6 |
| VSENSE ADC Data Resolution | VSENSE_RES | 16 | Bits | 6 | |||
| VBUS ADC Data Resolution | VBUS_RES | 16 | Bits | 14 bits are used for power calculations, 16 bits are reported when the VBUS measurement result is read | 6 | ||
| VSENSE Gain Accuracy | VSENSE_GAIN_ERR | -0.5 | 0.5 | % | -40°C to +125°C | 7 | |
| VSENSE Offset Accuracy, Referenced to Input | VSENSE_OFFSET_ERR | -100 | 25 | 100 | µV | 16-bit resolution | 7 |
| VBUS Gain Accuracy | VBUS_GAIN_ERR | -0.25 | 0.25 | % | At +25°C typical, -40°C to +125°C | 7 | |
| Time to First Communications | tINT_T | 50 | ms | Time after VDD is applied before it is ready to begin communication and measurement | 7 | ||
| Transition from Sleep State to Start of Conversion Cycle | tSLEEP_TO_ACTIVE | 5 | ms | Time from Sleep state exit commanded by register write to the beginning of the conversion cycle | 7 | ||
| Input High Voltage (SLOW/ALERT, SM_CLK, SM_DATA) | VIH | 1.35 | V | 7 | |||
| Input Low Voltage (SLOW/ALERT, SM_CLK, SM_DATA) | VIL | 0.8 | V | 7 | |||
| Output Low Voltage | VOL | 0.4 | V | Sinking 8 mA for the ALERT pins and 20 mA for the CLK pin in all modes. 4 mA for the SDA pin in 3.4 MHz mode. | 7 | ||
| Leakage Current | ILEAK | -0.5 | 0.5 | µA | Powered or unpowered | 7 | |
| Input High Voltage (PWRDN) | VIH | 1.3 | V | 7 | |||
| Input Low Voltage (PWRDN) | VIL | 0.6 | V | 7 | |||
| Clock Frequency | fSMB | 0.01 | 1 | MHz | Fast Mode Plus. No minimum if Time-out is not enabled. | 8 | |
| Clock Frequency | fSMB | 0.01 | 3.4 | MHz | High-Speed mode. No minimum if Time-out is not enabled. | 8 | |
| Spike Suppression | tSP | 0 | 50 | ns | Fast Mode Plus | 8 | |
| Spike Suppression | tSP | 0 | 10 | ns | High-Speed mode | 8 | |
| Bus Free Time Stop to Start | tBUF | 0.5 | µs | Per SMBus 3.1 | 8 | ||
| Hold Time after Repeated Start Condition | tHD:STA | 0.26 | µs | Per SMBus 3.1, Fast Mode Plus | 8 | ||
| Hold Time after Repeated Start Condition | tHD:STA | 0.16 | µs | Per SMBus 3.1, High-Speed mode | 8 | ||
| Repeated Start Condition Setup Time | tSU:STA | 0.26 | µs | Per SMBus 3.1, Fast Mode Plus | 8 | ||
| Repeated Start Condition Setup Time | tSU:STA | 0.16 | µs | Per SMBus 3.1, High-Speed mode | 8 | ||
| Setup Time: Stop | tSU:STO | 0.26 | µs | Per SMBus 3.1, Fast Mode Plus | 8 | ||
| Setup Time: Stop | tSU:STO | 0.16 | µs | Per SMBus 3.1, High-Speed mode | 8 | ||
| Data Setup Time | tSU:DAT | 50 | ns | Per SMBus 3.1, Fast Mode Plus | 8 | ||
| Data Setup Time | tSU:DAT | 10 | ns | Per SMBus 3.1, High-Speed mode | 8 | ||
| Data Hold Time | tHD:DAT | 0 | ns | Per SMBus 3.1, Fast Mode Plus | 8 | ||
| Data Hold Time | tHD:DAT | 0 | 70 | ns | Per SMBus 3.1, High-Speed mode | 8 | |
| Clock Low Period | tLOW | 0.5 | µs | Per SMBus 3.1, Fast Mode Plus | 8 | ||
| Clock Low Period | tLOW | 0.16 | µs | Per SMBus 3.1, High-Speed mode | 8 | ||
| Clock High Period | tHIGH | 0.26 | 50 | µs | Fast Mode Plus | 8 | |
| Clock High Period | tHIGH | 0.06 | 50 | µs | High-Speed mode | 8 | |
| Clock/Data Fall Time | tFALL | 12 | 120 | ns | Fast Mode Plus | 8 | |
| Clock/Data Rise Time | tRISE | 120 | ns | Fast Mode Plus | 8 | ||
| Clock Fall Time | tfCL | 10 | 40 | ns | High-Speed mode | 8 | |
| Clock Rise Time | trCL | 10 | 40 | ns | High-Speed mode | 8 | |
| Data Fall Time | tfDA | 10 | 80 | ns | High-Speed mode | 8 | |
| Data Rise Time | trDA | 10 | 80 | ns | High-Speed mode | 8 | |
| Capacitive Load | CLOAD | 550 | pF | Per bus line, Fast Mode Plus | 9 | ||
| Capacitive Load | CLOAD | 100 | pF | Per bus line, High-Speed mode | 9 | ||
| SLOW Pin Pulse Width | SLOWpw | 150 | µs | Pulses narrower than 150 µS may not be detected | 9 | ||
| Operating Temperature Range | TA | -40 | 125 | °C | 9 | ||
| Storage Temperature Range | TSTG | -55 | 150 | °C | 9 | ||
| Thermal Resistance, 16-Ball WLCSP | JA | 51.16 | °C/W | 9 |
CAD (KiCad official)
- Symbol:
PAC1952T-1E - Footprint:
Package_CSP:WLCSP-16_2.225x2.17mm_Layout4x4_P0.5mm - 3D model: WLCSP-16(2.2x2.2) (KiCad packages3D, STEP)
- 3D model files:
pac1952t-1e-etched.step/pac1952t-1e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pac1952t-1e.step/pac1952t-1e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (96 pp, sha256
52bb78abaa920f4f, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# PAC1952T-1E
**Microchip Tech** · Monitors & Reset Circuits · WLCSP-16(2.2x2.2)
PAC1952T-1E from Microchip Tech, in a WLCSP-16(2.2x2.2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| A1 | SENSE2+ | input | Analog input with a 0-FSR range for channel 2, connected to the supply side of the sense resistor; the safe operating voltage is up to 32V. |
| A2 | SENSE1- | input | Analog input with a 0-FSR range for channel 1, connected to the load side of the sense resistor; the safe operating voltage is up to 32V. |
| A3 | SENSE1+ | input | Analog input with a 0-FSR range for channel 1, connected to the supply side of the sense resistor and also used as the bus voltage input; the safe operating voltage is up to 32V. |
| A4 | VDD | power_in | Positive power supply input for the IC, 2.7V to 5.5V, to be bypassed with a 100 nF ceramic capacitor to ground near the IC. |
| B1 | SENSE2- | input | Analog input with a 0-FSR range for channel 2, connected to the load side of the sense resistor; the safe operating voltage is up to 32V. |
| B2 | GPIO/ALERT2 | bidirectional | Digital I/O that defaults to GPIO input mode and can be programmed as the open-drain ALERT2 indicator or open-drain GPIO, needing a pull-up resistor to VDD. |
| B3 | PWRDN | input | Active-low digital input that puts the device in a Power-Down state, with all circuitry including SMBus powered down. |
| B4 | GND | power_in | Ground for the IC. |
| C1 | SENSE3- | input | Inactive on PAC1952-1 in WLCSP; this pin must be grounded. |
| C2 | ADDRSEL | passive | Analog I/O pin for SMBus client address selection, with a resistor connected from this pin to ground. |
| C3 | SLOW/ALERT1 | bidirectional | Digital I/O that defaults to the SLOW input, where high forces all channels to 8 SPS, and can be programmed as the open-drain ALERT1 pin or GPIO. |
| C4 | SCL | input | SMBus/I2C clock input that needs an external pull-up resistor, except in High-Speed mode, which requires a CMOS driver from the host. |
| D1 | SENSE3+ | input | Inactive on PAC1952-1 in WLCSP; this pin must be grounded. |
| D2 | SENSE4- | input | Inactive on PAC1952-1 in WLCSP; this pin must be grounded. |
| D3 | SENSE4+ | input | Inactive on PAC1952-1 in WLCSP; this pin must be grounded. |
| D4 | SDA | bidirectional | Open-drain SMBus/I2C data I/O that requires a pull-up resistor to host VDD. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | WLCSP-16(2.2x2.2) |
| Category | Power Supply Chip |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD Pin | | -0.3 | | 6 | V | | 5 |
| Voltage on SENSE- and SENSE+ Pins | | -0.3 | | 40 | V | | 5 |
| Voltage on Any Other Pin to GND | | -0.3 | | 6 | V | | 5 |
| Input Current to Any Pin Except VDD | | -100 | | 100 | mA | | 5 |
| Operating Ambient Temperature Range | | -40 | | 150 | °C | | 5 |
| Storage Temperature Range | | -55 | | 150 | °C | | 5 |
| VDD Range | VDD | 2.7 | | 5.5 | V | | 6 |
| VDD Active Current | IDD | | 395 | 495 | µA | 1024 SPS, 4 channels enabled | 6 |
| VDD Active Current | IDD | | 395 | 440 | µA | 1024 SPS, 4 channels enabled, TA = 0°C to +85°C | 6 |
| VDD Active Current | IDD | | 12 | 25 | µA | 8 SPS, 4 channels enabled, TA = 0°C to +85°C | 6 |
| VDD Power-Down Current | IDD_PWRDN | 0 | | 8 | µA | | 6 |
| Bus Voltage Range | VBUS | -0.2 | | 32 | V | Common-mode voltage on SENSE pins, referenced to ground | 6 |
| VSENSE Differential Input Voltage Range | VSENSE_DIF | -100 | | 100 | mV | | 6 |
| SENSE+, SENSE- Pin Input Current | ISENSE+, ISENSE- | -6 | 0.6 | 6 | µA | VSENSE+ = VSENSE- = Full scale | 6 |
| SENSE+, SENSE- Pin Input Current | ISENSE+, ISENSE- | -1 | 0.4 | 1 | µA | VSENSE+ = 6V, VSENSE- = 5.9V | 6 |
| VSENSE ADC Data Resolution | VSENSE_RES | | | 16 | Bits | | 6 |
| VBUS ADC Data Resolution | VBUS_RES | | | 16 | Bits | 14 bits are used for power calculations, 16 bits are reported when the VBUS measurement result is read | 6 |
| VSENSE Gain Accuracy | VSENSE_GAIN_ERR | -0.5 | | 0.5 | % | -40°C to +125°C | 7 |
| VSENSE Offset Accuracy, Referenced to Input | VSENSE_OFFSET_ERR | -100 | 25 | 100 | µV | 16-bit resolution | 7 |
| VBUS Gain Accuracy | VBUS_GAIN_ERR | -0.25 | | 0.25 | % | At +25°C typical, -40°C to +125°C | 7 |
| Time to First Communications | tINT_T | | | 50 | ms | Time after VDD is applied before it is ready to begin communication and measurement | 7 |
| Transition from Sleep State to Start of Conversion Cycle | tSLEEP_TO_ACTIVE | | | 5 | ms | Time from Sleep state exit commanded by register write to the beginning of the conversion cycle | 7 |
| Input High Voltage (SLOW/ALERT, SM_CLK, SM_DATA) | VIH | 1.35 | | | V | | 7 |
| Input Low Voltage (SLOW/ALERT, SM_CLK, SM_DATA) | VIL | | | 0.8 | V | | 7 |
| Output Low Voltage | VOL | | | 0.4 | V | Sinking 8 mA for the ALERT pins and 20 mA for the CLK pin in all modes. 4 mA for the SDA pin in 3.4 MHz mode. | 7 |
| Leakage Current | ILEAK | -0.5 | | 0.5 | µA | Powered or unpowered | 7 |
| Input High Voltage (PWRDN) | VIH | 1.3 | | | V | | 7 |
| Input Low Voltage (PWRDN) | VIL | | | 0.6 | V | | 7 |
| Clock Frequency | fSMB | 0.01 | | 1 | MHz | Fast Mode Plus. No minimum if Time-out is not enabled. | 8 |
| Clock Frequency | fSMB | 0.01 | | 3.4 | MHz | High-Speed mode. No minimum if Time-out is not enabled. | 8 |
| Spike Suppression | tSP | 0 | | 50 | ns | Fast Mode Plus | 8 |
| Spike Suppression | tSP | 0 | | 10 | ns | High-Speed mode | 8 |
| Bus Free Time Stop to Start | tBUF | 0.5 | | | µs | Per SMBus 3.1 | 8 |
| Hold Time after Repeated Start Condition | tHD:STA | 0.26 | | | µs | Per SMBus 3.1, Fast Mode Plus | 8 |
| Hold Time after Repeated Start Condition | tHD:STA | 0.16 | | | µs | Per SMBus 3.1, High-Speed mode | 8 |
| Repeated Start Condition Setup Time | tSU:STA | 0.26 | | | µs | Per SMBus 3.1, Fast Mode Plus | 8 |
| Repeated Start Condition Setup Time | tSU:STA | 0.16 | | | µs | Per SMBus 3.1, High-Speed mode | 8 |
| Setup Time: Stop | tSU:STO | 0.26 | | | µs | Per SMBus 3.1, Fast Mode Plus | 8 |
| Setup Time: Stop | tSU:STO | 0.16 | | | µs | Per SMBus 3.1, High-Speed mode | 8 |
| Data Setup Time | tSU:DAT | 50 | | | ns | Per SMBus 3.1, Fast Mode Plus | 8 |
| Data Setup Time | tSU:DAT | 10 | | | ns | Per SMBus 3.1, High-Speed mode | 8 |
| Data Hold Time | tHD:DAT | 0 | | | ns | Per SMBus 3.1, Fast Mode Plus | 8 |
| Data Hold Time | tHD:DAT | 0 | | 70 | ns | Per SMBus 3.1, High-Speed mode | 8 |
| Clock Low Period | tLOW | 0.5 | | | µs | Per SMBus 3.1, Fast Mode Plus | 8 |
| Clock Low Period | tLOW | 0.16 | | | µs | Per SMBus 3.1, High-Speed mode | 8 |
| Clock High Period | tHIGH | 0.26 | | 50 | µs | Fast Mode Plus | 8 |
| Clock High Period | tHIGH | 0.06 | | 50 | µs | High-Speed mode | 8 |
| Clock/Data Fall Time | tFALL | 12 | | 120 | ns | Fast Mode Plus | 8 |
| Clock/Data Rise Time | tRISE | | | 120 | ns | Fast Mode Plus | 8 |
| Clock Fall Time | tfCL | 10 | | 40 | ns | High-Speed mode | 8 |
| Clock Rise Time | trCL | 10 | | 40 | ns | High-Speed mode | 8 |
| Data Fall Time | tfDA | 10 | | 80 | ns | High-Speed mode | 8 |
| Data Rise Time | trDA | 10 | | 80 | ns | High-Speed mode | 8 |
| Capacitive Load | CLOAD | | | 550 | pF | Per bus line, Fast Mode Plus | 9 |
| Capacitive Load | CLOAD | | | 100 | pF | Per bus line, High-Speed mode | 9 |
| SLOW Pin Pulse Width | SLOWpw | 150 | | | µs | Pulses narrower than 150 µS may not be detected | 9 |
| Operating Temperature Range | TA | -40 | | 125 | °C | | 9 |
| Storage Temperature Range | TSTG | -55 | | 150 | °C | | 9 |
| Thermal Resistance, 16-Ball WLCSP | JA | | 51.16 | | °C/W | | 9 |
## CAD (KiCad official)
- Symbol: `PAC1952T-1E`
- Footprint: `Package_CSP:WLCSP-16_2.225x2.17mm_Layout4x4_P0.5mm`
- 3D model: WLCSP-16(2.2x2.2) (KiCad packages3D, STEP)
- 3D model files: `pac1952t-1e-etched.step` / `pac1952t-1e-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `pac1952t-1e.step` / `pac1952t-1e.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](https://ww1.microchip.com/downloads/en/DeviceDoc/PAC195X-Family-Data-Sheet-20006539B.pdf) (96 pp, sha256 `52bb78abaa920f4f`, retrieved 2026-10-29, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/pac1952t-1e-datasheet.pdf)