main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers pac1952t-1e: symbol repaired (body fitted to the names) · Ray
pac1952t-1e-etched.glb Publish 0.1.0 · Ray
pac1952t-1e-etched.step pac1952t-1e: factory component page (tier=mfr) · Ray
pac1952t-1e-hero.glb pac1952t-1e: hero GLB from the etched model (keeps the MPN mark) · Ray
pac1952t-1e-hero.overlay.json Publish 0.1.0 · Ray
pac1952t-1e.glb Publish 0.1.0 · Ray
pac1952t-1e.kicad_mod Publish 0.1.0 · Ray
pac1952t-1e.kicad_sym pac1952t-1e: symbol repaired (body fitted to the names) · Ray
pac1952t-1e.lbr pac1952t-1e: symbol repaired (body fitted to the names) · Ray
pac1952t-1e.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray

PAC1952T-1E

Microchip Tech · Monitors & Reset Circuits · WLCSP-16(2.2x2.2)

PAC1952T-1E from Microchip Tech, in a WLCSP-16(2.2x2.2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
A1 SENSE2+ input Analog input with a 0-FSR range for channel 2, connected to the supply side of the sense resistor; the safe operating voltage is up to 32V.
A2 SENSE1- input Analog input with a 0-FSR range for channel 1, connected to the load side of the sense resistor; the safe operating voltage is up to 32V.
A3 SENSE1+ input Analog input with a 0-FSR range for channel 1, connected to the supply side of the sense resistor and also used as the bus voltage input; the safe operating voltage is up to 32V.
A4 VDD power_in Positive power supply input for the IC, 2.7V to 5.5V, to be bypassed with a 100 nF ceramic capacitor to ground near the IC.
B1 SENSE2- input Analog input with a 0-FSR range for channel 2, connected to the load side of the sense resistor; the safe operating voltage is up to 32V.
B2 GPIO/ALERT2 bidirectional Digital I/O that defaults to GPIO input mode and can be programmed as the open-drain ALERT2 indicator or open-drain GPIO, needing a pull-up resistor to VDD.
B3 PWRDN input Active-low digital input that puts the device in a Power-Down state, with all circuitry including SMBus powered down.
B4 GND power_in Ground for the IC.
C1 SENSE3- input Inactive on PAC1952-1 in WLCSP; this pin must be grounded.
C2 ADDRSEL passive Analog I/O pin for SMBus client address selection, with a resistor connected from this pin to ground.
C3 SLOW/ALERT1 bidirectional Digital I/O that defaults to the SLOW input, where high forces all channels to 8 SPS, and can be programmed as the open-drain ALERT1 pin or GPIO.
C4 SCL input SMBus/I2C clock input that needs an external pull-up resistor, except in High-Speed mode, which requires a CMOS driver from the host.
D1 SENSE3+ input Inactive on PAC1952-1 in WLCSP; this pin must be grounded.
D2 SENSE4- input Inactive on PAC1952-1 in WLCSP; this pin must be grounded.
D3 SENSE4+ input Inactive on PAC1952-1 in WLCSP; this pin must be grounded.
D4 SDA bidirectional Open-drain SMBus/I2C data I/O that requires a pull-up resistor to host VDD.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package WLCSP-16(2.2x2.2)
Category Power Supply Chip
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VDD Pin -0.3 6 V 5
Voltage on SENSE- and SENSE+ Pins -0.3 40 V 5
Voltage on Any Other Pin to GND -0.3 6 V 5
Input Current to Any Pin Except VDD -100 100 mA 5
Operating Ambient Temperature Range -40 150 °C 5
Storage Temperature Range -55 150 °C 5
VDD Range VDD 2.7 5.5 V 6
VDD Active Current IDD 395 495 µA 1024 SPS, 4 channels enabled 6
VDD Active Current IDD 395 440 µA 1024 SPS, 4 channels enabled, TA = 0°C to +85°C 6
VDD Active Current IDD 12 25 µA 8 SPS, 4 channels enabled, TA = 0°C to +85°C 6
VDD Power-Down Current IDD_PWRDN 0 8 µA 6
Bus Voltage Range VBUS -0.2 32 V Common-mode voltage on SENSE pins, referenced to ground 6
VSENSE Differential Input Voltage Range VSENSE_DIF -100 100 mV 6
SENSE+, SENSE- Pin Input Current ISENSE+, ISENSE- -6 0.6 6 µA VSENSE+ = VSENSE- = Full scale 6
SENSE+, SENSE- Pin Input Current ISENSE+, ISENSE- -1 0.4 1 µA VSENSE+ = 6V, VSENSE- = 5.9V 6
VSENSE ADC Data Resolution VSENSE_RES 16 Bits 6
VBUS ADC Data Resolution VBUS_RES 16 Bits 14 bits are used for power calculations, 16 bits are reported when the VBUS measurement result is read 6
VSENSE Gain Accuracy VSENSE_GAIN_ERR -0.5 0.5 % -40°C to +125°C 7
VSENSE Offset Accuracy, Referenced to Input VSENSE_OFFSET_ERR -100 25 100 µV 16-bit resolution 7
VBUS Gain Accuracy VBUS_GAIN_ERR -0.25 0.25 % At +25°C typical, -40°C to +125°C 7
Time to First Communications tINT_T 50 ms Time after VDD is applied before it is ready to begin communication and measurement 7
Transition from Sleep State to Start of Conversion Cycle tSLEEP_TO_ACTIVE 5 ms Time from Sleep state exit commanded by register write to the beginning of the conversion cycle 7
Input High Voltage (SLOW/ALERT, SM_CLK, SM_DATA) VIH 1.35 V 7
Input Low Voltage (SLOW/ALERT, SM_CLK, SM_DATA) VIL 0.8 V 7
Output Low Voltage VOL 0.4 V Sinking 8 mA for the ALERT pins and 20 mA for the CLK pin in all modes. 4 mA for the SDA pin in 3.4 MHz mode. 7
Leakage Current ILEAK -0.5 0.5 µA Powered or unpowered 7
Input High Voltage (PWRDN) VIH 1.3 V 7
Input Low Voltage (PWRDN) VIL 0.6 V 7
Clock Frequency fSMB 0.01 1 MHz Fast Mode Plus. No minimum if Time-out is not enabled. 8
Clock Frequency fSMB 0.01 3.4 MHz High-Speed mode. No minimum if Time-out is not enabled. 8
Spike Suppression tSP 0 50 ns Fast Mode Plus 8
Spike Suppression tSP 0 10 ns High-Speed mode 8
Bus Free Time Stop to Start tBUF 0.5 µs Per SMBus 3.1 8
Hold Time after Repeated Start Condition tHD:STA 0.26 µs Per SMBus 3.1, Fast Mode Plus 8
Hold Time after Repeated Start Condition tHD:STA 0.16 µs Per SMBus 3.1, High-Speed mode 8
Repeated Start Condition Setup Time tSU:STA 0.26 µs Per SMBus 3.1, Fast Mode Plus 8
Repeated Start Condition Setup Time tSU:STA 0.16 µs Per SMBus 3.1, High-Speed mode 8
Setup Time: Stop tSU:STO 0.26 µs Per SMBus 3.1, Fast Mode Plus 8
Setup Time: Stop tSU:STO 0.16 µs Per SMBus 3.1, High-Speed mode 8
Data Setup Time tSU:DAT 50 ns Per SMBus 3.1, Fast Mode Plus 8
Data Setup Time tSU:DAT 10 ns Per SMBus 3.1, High-Speed mode 8
Data Hold Time tHD:DAT 0 ns Per SMBus 3.1, Fast Mode Plus 8
Data Hold Time tHD:DAT 0 70 ns Per SMBus 3.1, High-Speed mode 8
Clock Low Period tLOW 0.5 µs Per SMBus 3.1, Fast Mode Plus 8
Clock Low Period tLOW 0.16 µs Per SMBus 3.1, High-Speed mode 8
Clock High Period tHIGH 0.26 50 µs Fast Mode Plus 8
Clock High Period tHIGH 0.06 50 µs High-Speed mode 8
Clock/Data Fall Time tFALL 12 120 ns Fast Mode Plus 8
Clock/Data Rise Time tRISE 120 ns Fast Mode Plus 8
Clock Fall Time tfCL 10 40 ns High-Speed mode 8
Clock Rise Time trCL 10 40 ns High-Speed mode 8
Data Fall Time tfDA 10 80 ns High-Speed mode 8
Data Rise Time trDA 10 80 ns High-Speed mode 8
Capacitive Load CLOAD 550 pF Per bus line, Fast Mode Plus 9
Capacitive Load CLOAD 100 pF Per bus line, High-Speed mode 9
SLOW Pin Pulse Width SLOWpw 150 µs Pulses narrower than 150 µS may not be detected 9
Operating Temperature Range TA -40 125 °C 9
Storage Temperature Range TSTG -55 150 °C 9
Thermal Resistance, 16-Ball WLCSP JA 51.16 °C/W 9

CAD (KiCad official)

  • Symbol: PAC1952T-1E
  • Footprint: Package_CSP:WLCSP-16_2.225x2.17mm_Layout4x4_P0.5mm
  • 3D model: WLCSP-16(2.2x2.2) (KiCad packages3D, STEP)
  • 3D model files: pac1952t-1e-etched.step / pac1952t-1e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); pac1952t-1e.step / pac1952t-1e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (96 pp, sha256 52bb78abaa920f4f, retrieved 2026-10-29, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF