main
Ray
Publish 0.1.0
14eb31b
OPA692IDBVR
Texas Instruments · Video Amplifiers · SOT-23-6
OPA692IDBVR from Texas Instruments, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | Output | output | Amplifier output, delivering ±190mA typical (±160mA min at +25°C) with ±4.0V no-load swing on ±5V supplies; goes high-impedance when DIS is pulled LOW. |
| 2 | -VS | power_in | Negative supply pin (ground for single-supply use); absolute maximum total supply ±6.5V, operating range ±2.5V to ±6V dual. |
| 3 | +IN | input | Noninverting input with 100kΩ |
| 4 | -IN | input | Inverting input tied to internal 402Ω RF/RG network; ground for gain +2, leave open for gain +1, or drive with signal (with +IN grounded) for gain -1. |
| 5 | DIS | input | Disable control: leave open or hold HIGH (enable voltage 3.5V min at +25°C) for normal operation, pull LOW (disable voltage 1.7V max) to cut supply current to under 150µA and put I/O pins in high-impedance state. |
| 6 | +VS | power_in | Positive supply pin; operating range +5V to +12V single supply, ±6V max dual, and should be decoupled with 0.1µF capacitor close to the pin. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOT-23-6 |
| Category | Amplifiers/Comparators |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Small-Signal Bandwidth | 185 | 225 | MHz | VS = ±5V; G = +2; VO < 0.5VPP | 3 | ||
| Bandwidth for 0.1dB Gain Flatness | 40 | 120 | MHz | VS = ±5V; G = +2, VO < 0.5VPP | 3 | ||
| Peaking at a Gain of +1 | 0.2 | 1 | dB | VS = ±5V; VO < 0.5VPP | 3 | ||
| Slew Rate | 1400 | 2000 | V/µs | VS = ±5V; G = +2, 4V Step | 3 | ||
| Gain Error | -1.5 | 0.3 | 1.5 | % | VS = ±5V; G = +2 | 3 | |
| Gain Error | -1.5 | 0.2 | 1.5 | % | VS = ±5V; G = -1 | 3 | |
| Internal RF and RG Maximum | 402 | 457 | Ω | VS = ±5V | 3 | ||
| Internal RF and RG Minimum | 347 | 402 | Ω | VS = ±5V | 3 | ||
| Internal RF and RG Average Drift | 0.13 | 0.13 | %/C° | VS = ±5V | 3 | ||
| Input Offset Voltage | -2.5 | 0.5 | 2.5 | mV | VS = ±5V; VCM = 0V | 3 | |
| Noninverting Input Bias Current | 15 | 35 | µA | VS = ±5V; VCM = 0V | 3 | ||
| Inverting Input Bias Current | -25 | 5 | 25 | µA | VS = ±5V; VCM = 0V | 3 | |
| Common-Mode Input Range | -3.4 | 3.5 | V | VS = ±5V | 3 | ||
| Voltage Output Swing | -3.8 | 4 | V | VS = ±5V; No Load | 3 | ||
| Voltage Output Swing | -3.7 | 3.9 | V | VS = ±5V; 100Ω Load | 3 | ||
| Current Output, Sourcing | 160 | 190 | mA | VS = ±5V | 3 | ||
| Current Output, Sinking | -160 | -190 | mA | VS = ±5V | 3 | ||
| Power-Down Supply Current (+VS) | -150 | -300 | µA | VS = ±5V; VDIS = 0 | 4 | ||
| Enable Voltage | 3.5 | 3.3 | V | VS = ±5V | 4 | ||
| Disable Voltage | 1.8 | 1.7 | V | VS = ±5V | 4 | ||
| Control Pin Input Bias Current | 75 | 130 | µA | VS = ±5V; VDIS = 0 | 4 | ||
| Maximum Operating Voltage Range | -6 | 6 | V | 4 | |||
| Maximum Quiescent Current | 5.1 | 5.3 | mA | VS = ±5V | 4 | ||
| Minimum Quiescent Current | 4.9 | 5.1 | mA | VS = ±5V | 4 | ||
| Power-Supply Rejection Ratio (-PSRR) | 52 | 58 | dB | VS = ±5V; Input Referred | 4 | ||
| Small-Signal Bandwidth | 168 | 190 | MHz | VS = +5V; G = +2, VO < 0.5VPP | 5 | ||
| Bandwidth for 0.1dB Gain Flatness | 40 | 90 | MHz | VS = +5V; G = +2, VO < 0.5VPP | 5 | ||
| Peaking at a Gain of +1 | 0.2 | 1 | dB | VS = +5V; VO < 0.5VPP | 5 | ||
| Slew Rate | 600 | 830 | V/µs | VS = +5V; G = +2, 2V Step | 5 | ||
| Gain Error | -1.5 | 0.3 | 1.5 | % | VS = +5V; G = +2 | 5 | |
| Gain Error | -1.5 | 0.2 | 1.5 | % | VS = +5V; G = -1 | 5 | |
| Internal RF and RG Maximum | 402 | 457 | Ω | VS = +5V | 5 | ||
| Internal RF and RG Minimum | 347 | 402 | Ω | VS = +5V | 5 | ||
| Internal RF and RG Average Drift | 0.13 | 0.13 | %/C° | VS = +5V | 5 | ||
| Input Offset Voltage | -3 | 0.5 | 3 | mV | VS = +5V; VCM = 2.5V | 5 | |
| Noninverting Input Bias Current | 20 | 40 | µA | VS = +5V; VCM = 2.5V | 5 | ||
| Inverting Input Bias Current | -25 | 5 | 25 | µA | VS = +5V; VCM = 2.5V | 5 | |
| Least Positive Input Voltage | 1.5 | 1.6 | V | VS = +5V | 5 | ||
| Most Positive Input Voltage | 3.4 | 3.5 | V | VS = +5V | 5 | ||
| Most Positive Output Voltage | 3.8 | 4 | V | VS = +5V; No Load | 5 | ||
| Most Positive Output Voltage | 3.7 | 3.9 | V | VS = +5V; RL = 100Ω | 5 | ||
| Least Positive Output Voltage | 1 | 1.2 | V | VS = +5V; No Load | 5 | ||
| Least Positive Output Voltage | 1.1 | 1.3 | V | VS = +5V; RL = 100Ω | 5 | ||
| Current Output, Sourcing | 120 | 160 | mA | VS = +5V | 5 | ||
| Current Output, Sinking | -120 | -160 | mA | VS = +5V | 5 | ||
| Maximum Single-Supply Operating Voltage | 12 | V | 6 | ||||
| Enable Voltage | 3.5 | 3.3 | V | VS = +5V | 6 | ||
| Disable Voltage | 1.8 | 1.7 | V | VS = +5V | 6 | ||
| Maximum Quiescent Current | 4.5 | 4.8 | mA | VS = +5V | 6 | ||
| Minimum Quiescent Current | 4.1 | 4.5 | mA | VS = +5V | 6 | ||
| Power Supply | -6.5 | 6.5 | V | VDC | 2 | ||
| Differential Input Voltage | -1.2 | 1.2 | V | Noninverting input to internal inverting node | 2 | ||
| Storage Temperature Range | -65 | 125 | °C | D, DVB | 2 | ||
| Lead Temperature | 300 | °C | soldering, 10s | 2 | |||
| Junction Temperature (TJ) | TJ | 175 | °C | 2 | |||
| ESD Resistance HBM | 2 | kV | HBM | 2 | |||
| ESD Resistance MM | 200 | V | MM | 2 | |||
| Specification: D, DBV (Temperature Range) | -40 | 85 | °C | D, DBV | 4 | ||
| Thermal Resistance, θJA DBV SOT23-6 | θJA | 150 | °C/W | DBV SOT23-6 | 4 |
CAD (KiCad official)
- Symbol:
OPA692IDBVR - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
opa692idbvr-etched.step/opa692idbvr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);opa692idbvr.step/opa692idbvr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (33 pp, sha256
50af9953896a9604, retrieved 2026-11-11, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# OPA692IDBVR
**Texas Instruments** · Video Amplifiers · SOT-23-6
OPA692IDBVR from Texas Instruments, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | Output | output | Amplifier output, delivering ±190mA typical (±160mA min at +25°C) with ±4.0V no-load swing on ±5V supplies; goes high-impedance when DIS is pulled LOW. |
| 2 | -VS | power_in | Negative supply pin (ground for single-supply use); absolute maximum total supply ±6.5V, operating range ±2.5V to ±6V dual. |
| 3 | +IN | input | Noninverting input with 100kΩ || 2pF impedance; drive it with the signal for gain +2 or +1, or ground it for gain of -1. |
| 4 | -IN | input | Inverting input tied to internal 402Ω RF/RG network; ground for gain +2, leave open for gain +1, or drive with signal (with +IN grounded) for gain -1. |
| 5 | DIS | input | Disable control: leave open or hold HIGH (enable voltage 3.5V min at +25°C) for normal operation, pull LOW (disable voltage 1.7V max) to cut supply current to under 150µA and put I/O pins in high-impedance state. |
| 6 | +VS | power_in | Positive supply pin; operating range +5V to +12V single supply, ±6V max dual, and should be decoupled with 0.1µF capacitor close to the pin. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOT-23-6 |
| Category | Amplifiers/Comparators |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Small-Signal Bandwidth | | 185 | 225 | | MHz | VS = ±5V; G = +2; VO < 0.5VPP | 3 |
| Bandwidth for 0.1dB Gain Flatness | | 40 | 120 | | MHz | VS = ±5V; G = +2, VO < 0.5VPP | 3 |
| Peaking at a Gain of +1 | | | 0.2 | 1 | dB | VS = ±5V; VO < 0.5VPP | 3 |
| Slew Rate | | 1400 | 2000 | | V/µs | VS = ±5V; G = +2, 4V Step | 3 |
| Gain Error | | -1.5 | 0.3 | 1.5 | % | VS = ±5V; G = +2 | 3 |
| Gain Error | | -1.5 | 0.2 | 1.5 | % | VS = ±5V; G = -1 | 3 |
| Internal RF and RG Maximum | | | 402 | 457 | Ω | VS = ±5V | 3 |
| Internal RF and RG Minimum | | 347 | 402 | | Ω | VS = ±5V | 3 |
| Internal RF and RG Average Drift | | | 0.13 | 0.13 | %/C° | VS = ±5V | 3 |
| Input Offset Voltage | | -2.5 | 0.5 | 2.5 | mV | VS = ±5V; VCM = 0V | 3 |
| Noninverting Input Bias Current | | | 15 | 35 | µA | VS = ±5V; VCM = 0V | 3 |
| Inverting Input Bias Current | | -25 | 5 | 25 | µA | VS = ±5V; VCM = 0V | 3 |
| Common-Mode Input Range | | -3.4 | 3.5 | | V | VS = ±5V | 3 |
| Voltage Output Swing | | -3.8 | 4 | | V | VS = ±5V; No Load | 3 |
| Voltage Output Swing | | -3.7 | 3.9 | | V | VS = ±5V; 100Ω Load | 3 |
| Current Output, Sourcing | | 160 | 190 | | mA | VS = ±5V | 3 |
| Current Output, Sinking | | -160 | -190 | | mA | VS = ±5V | 3 |
| Power-Down Supply Current (+VS) | | | -150 | -300 | µA | VS = ±5V; VDIS = 0 | 4 |
| Enable Voltage | | 3.5 | 3.3 | | V | VS = ±5V | 4 |
| Disable Voltage | | | 1.8 | 1.7 | V | VS = ±5V | 4 |
| Control Pin Input Bias Current | | | 75 | 130 | µA | VS = ±5V; VDIS = 0 | 4 |
| Maximum Operating Voltage Range | | -6 | | 6 | V | | 4 |
| Maximum Quiescent Current | | | 5.1 | 5.3 | mA | VS = ±5V | 4 |
| Minimum Quiescent Current | | 4.9 | 5.1 | | mA | VS = ±5V | 4 |
| Power-Supply Rejection Ratio (-PSRR) | | 52 | 58 | | dB | VS = ±5V; Input Referred | 4 |
| Small-Signal Bandwidth | | 168 | 190 | | MHz | VS = +5V; G = +2, VO < 0.5VPP | 5 |
| Bandwidth for 0.1dB Gain Flatness | | 40 | 90 | | MHz | VS = +5V; G = +2, VO < 0.5VPP | 5 |
| Peaking at a Gain of +1 | | | 0.2 | 1 | dB | VS = +5V; VO < 0.5VPP | 5 |
| Slew Rate | | 600 | 830 | | V/µs | VS = +5V; G = +2, 2V Step | 5 |
| Gain Error | | -1.5 | 0.3 | 1.5 | % | VS = +5V; G = +2 | 5 |
| Gain Error | | -1.5 | 0.2 | 1.5 | % | VS = +5V; G = -1 | 5 |
| Internal RF and RG Maximum | | | 402 | 457 | Ω | VS = +5V | 5 |
| Internal RF and RG Minimum | | 347 | 402 | | Ω | VS = +5V | 5 |
| Internal RF and RG Average Drift | | | 0.13 | 0.13 | %/C° | VS = +5V | 5 |
| Input Offset Voltage | | -3 | 0.5 | 3 | mV | VS = +5V; VCM = 2.5V | 5 |
| Noninverting Input Bias Current | | | 20 | 40 | µA | VS = +5V; VCM = 2.5V | 5 |
| Inverting Input Bias Current | | -25 | 5 | 25 | µA | VS = +5V; VCM = 2.5V | 5 |
| Least Positive Input Voltage | | | 1.5 | 1.6 | V | VS = +5V | 5 |
| Most Positive Input Voltage | | 3.4 | 3.5 | | V | VS = +5V | 5 |
| Most Positive Output Voltage | | 3.8 | 4 | | V | VS = +5V; No Load | 5 |
| Most Positive Output Voltage | | 3.7 | 3.9 | | V | VS = +5V; RL = 100Ω | 5 |
| Least Positive Output Voltage | | | 1 | 1.2 | V | VS = +5V; No Load | 5 |
| Least Positive Output Voltage | | | 1.1 | 1.3 | V | VS = +5V; RL = 100Ω | 5 |
| Current Output, Sourcing | | 120 | 160 | | mA | VS = +5V | 5 |
| Current Output, Sinking | | -120 | -160 | | mA | VS = +5V | 5 |
| Maximum Single-Supply Operating Voltage | | | | 12 | V | | 6 |
| Enable Voltage | | 3.5 | 3.3 | | V | VS = +5V | 6 |
| Disable Voltage | | | 1.8 | 1.7 | V | VS = +5V | 6 |
| Maximum Quiescent Current | | | 4.5 | 4.8 | mA | VS = +5V | 6 |
| Minimum Quiescent Current | | 4.1 | 4.5 | | mA | VS = +5V | 6 |
| Power Supply | | -6.5 | | 6.5 | V | VDC | 2 |
| Differential Input Voltage | | -1.2 | | 1.2 | V | Noninverting input to internal inverting node | 2 |
| Storage Temperature Range | | -65 | | 125 | °C | D, DVB | 2 |
| Lead Temperature | | | | 300 | °C | soldering, 10s | 2 |
| Junction Temperature (TJ) | TJ | | | 175 | °C | | 2 |
| ESD Resistance HBM | | | | 2 | kV | HBM | 2 |
| ESD Resistance MM | | | | 200 | V | MM | 2 |
| Specification: D, DBV (Temperature Range) | | -40 | | 85 | °C | D, DBV | 4 |
| Thermal Resistance, θJA DBV SOT23-6 | θJA | | 150 | | °C/W | DBV SOT23-6 | 4 |
## CAD (KiCad official)
- Symbol: `OPA692IDBVR`
- Footprint: `Package_TO_SOT_SMD:SOT-23-6`
- 3D model: SOT-23-6, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `opa692idbvr-etched.step` / `opa692idbvr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `opa692idbvr.step` / `opa692idbvr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/opa692.pdf) (33 pp, sha256 `50af9953896a9604`, retrieved 2026-11-11, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/opa692idbvr-datasheet.pdf)