main
Ray
Publish 0.1.0
9069dfd
ONET1191VRGPT
Texas Instruments · Laser Drivers · QFN-20(4x4)
ONET1191VRGPT from Texas Instruments, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DIS | input | Disables both bias and modulation currents when set high, and toggling it resets a fault condition. |
| 2 | RZTC | passive | An external zero-TC 28.7-kΩ resistor to ground sets a defined zero-TC reference current for the internal DACs. |
| 3 | TS | output | Temperature sensor output, not buffered and drives capacitive loads only, with VTS = 8.2 mV/°C × TEMP + 1140 mV. |
| 4 | SCK | input | Two-wire interface serial clock input with a 100-kΩ pullup resistor to VCC. |
| 5 | SDA | input | Two-wire interface serial data input with a 100-kΩ pullup resistor to VCC. |
| 6 | GND | power_in | Circuit ground. |
| 7 | DIN+ | input | Noninverted data input, on-chip differentially 100-Ω terminated to DIN-, must be ac-coupled. |
| 8 | DIN- | input | Inverted data input, on-chip differentially 100-Ω terminated to DIN+, must be ac-coupled. |
| 9 | GND | power_in | Circuit ground. |
| 10 | FLT | output | Fault detection flag output. |
| 11 | BGV | output | Buffered bandgap voltage with open emitter output, a replica of the RZTC bandgap voltage; use the same 28.7-kΩ resistor to GND as at RZTC for best matching. |
| 12 | MONB | output | Bias current monitor sourcing a 3.3% replica of the bias current; a fault is triggered if the voltage exceeds 1.15 V, and about 0.8 V at the maximum desired bias current is typical. |
| 13 | MONP | output | Photodiode current monitor sourcing a 50% replica when PDR = 1 and a 250% replica when PDR = 0, with an external resistor (5 kΩ typical) to ground. |
| 14 | COMP | passive | Compensation pin controlling the APC loop bandwidth, requiring a 0.01-µF capacitor to ground. |
| 15 | PD | passive | Photodiode input that sources or sinks current depending on PDP and supplies >1.5 V reverse bias. |
| 16 | BIAS | passive | Sinks average VCSEL bias current in APC and open-loop modes and connects to the laser cathode through an inductor (BLM15HG102SN1D recommended). |
| 17 | VCC | power_in | Supply pin for the 3.3-V ±10% supply voltage. |
| 18 | MOD- | output | Inverted modulation current output, on-chip 55-Ω back-terminated to VCC. |
| 19 | MOD+ | output | Noninverted modulation current output, on-chip 55-Ω back-terminated to VCC. |
| 20 | VCC | power_in | Supply pin for the 3.3-V ±10% supply voltage. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | QFN-20(4x4) |
| Category | Power Supply Chip |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | -0.3 | 4 | V | 9 | ||
| Voltage at DIS, RZTC, TS, SCK, SDA, DIN+, DIN-, FLT, BGV, MONB, MONP, CAPC, PD, BIAS, MOD+, MOD- | -0.3 | 4 | V | Respect to network ground | 9 | ||
| ESD rating at all pins | 2 | kV | HBM | 9 | |||
| Maximum junction temperature | TJ,max | 125 | °C | 9 | |||
| Storage temperature range | Tstg | -65 | 85 | °C | 9 | ||
| Lead temperature | TLEAD | 260 | °C | 1.6 mm (1/16 inch) from case for 10 seconds | 9 | ||
| Supply voltage | VCC | 2.9 | 3.3 | 3.6 | V | 10 | |
| Digital input high voltage | VIH | 2 | V | DIS, SCK, SDA | 10 | ||
| Digital input low voltage | VIL | 0.8 | V | DIS, SCK, SDA | 10 | ||
| Bias output headroom voltage | VBIAS - GND | 300 | mV | 10 | |||
| Photodiode current range | 12 | 640 | µA | Control bit PDR = 1, step size = 2.5 µA | 10 | ||
| Photodiode current range | 2.5 | 128 | µA | Control bit PDR = 0, step size = 0.5 µA | 10 | ||
| Zero-TC resistor value | RRZTC | 28.4 | 28.7 | 29 | kΩ | 1.15-V bandgap bias across resistor | 10 |
| Differential input voltage swing | VIN | 200 | 1200 | mVp-p | Control bit EQENA = 1 | 10 | |
| Differential input voltage swing | VIN | 500 | 1200 | mVp-p | Control bit EQENA = 0 | 10 | |
| Input rise time | tR-IN | 30 | 55 | ps | 20%-80% | 10 | |
| Input fall time | tF-IN | 30 | 55 | ps | 20%-80% | 10 | |
| Operating free-air temperature | TA | -40 | 85 | °C | 10 | ||
| Supply current | IVCC | 62 | 71 | mA | IMODC = 24 mA, IBIASC = 6 mA, including IMODC and IBIASC, EQENB = 1 | 11 | |
| Supply current | IVCC | 70 | mA | IMODC = 24 mA, IBIASC = 6 mA, including IMODC and IBIASC, EQENB = 0 | 11 | ||
| Supply current disabled | IVCC | 35 | 42 | mA | Disabled, DIS = high and/or control bit ENA = low, EQENB = 1 | 11 | |
| Data input resistance | RIN | 85 | 100 | 125 | Ω | Differential between DIN+/DIN- | 11 |
| Data output resistance | ROUT | 45 | 55 | 65 | Ω | Single-ended to VCC | 11 |
| Digital input current | -50 | 10 | µA | SCK, SDA, 100-kΩ pullup to VCC | 11 | ||
| Digital input current | -10 | 10 | µA | DIS | 11 | ||
| Digital output high voltage | VOH | 2.4 | V | FLT, ISOURCE = 500 µA | 11 | ||
| Digital output low voltage | VOL | 0.4 | V | FLT, ISINK = 500 µA | 11 | ||
| Bias current during disable | IBIAS-DIS | 100 | µA | 11 | |||
| Minimum bias current | IBIAS-MIN | 0.2 | mA | See (2) | 11 | ||
| Maximum bias current | IBIAS-MAX | 14 | 20 | mA | DAC set to maximum, open- and closed-loop | 11 | |
| Photodiode reverse bias voltage | VPD | 1.5 | 2.3 | V | APC active, IPD = max | 11 | |
| Temperature sensor voltage range | VTS | 0.5 | 2.5 | V | Capacitive load only, with midscale calibration | 11 | |
| Temperature sensor accuracy | -3 | 3 | °C | With midscale calibration | 11 | ||
| Temperature sensor drive current | ITS | -1 | 1 | µA | Source or sink | 11 | |
| Photodiode current monitor ratio IMONP/IPD | 40 | 50 | 60 | % | Control bit PDR = 1 | 11 | |
| Photodiode current monitor ratio IMONP/IPD | 200 | 265 | 300 | % | Control bit PDR = 0 | 11 | |
| Bias current monitor ratio IMONB/IBIAS | 2.7 | 3.3 | 4 | % | 1.2-kΩ sense resistor; nominal 1/30 = 3.3% | 11 | |
| VCC reset threshold voltage | VCC-RST | 2.4 | 2.5 | 2.8 | V | VCC voltage level which triggers power-on reset | 11 |
| VCC reset threshold hysteresis | VCC-RSTHYS | 100 | mV | 11 | |||
| Fault voltage at MONB | VMONB-FLT | 1.05 | 1.15 | 1.25 | V | Fault occurs if voltage at MONB exceeds value | 11 |
| Output rise time | tr-OUT | 20 | 30 | ps | 20%-80%, tr-IN < 40 ps, 50-Ω load | 12 | |
| Output fall time | tf-OUT | 25 | 30 | ps | 20%-80%, tf-IN < 40 ps, 50-Ω load | 12 | |
| Maximum modulation current | IMOD-MAX | 36 | 45 | mA | Control bit MODR = 1, 50-Ω load | 12 | |
| Maximum modulation current | IMOD-MAX | 18 | 27 | mA | Control bit MODR = 0, 50-Ω load | 12 | |
| Deterministic output jitter | DJ | 4 | 12 | ps p-p | Control bit EQENB = 1, K28.5 pattern at 11.3 Gbps | 12 | |
| Deterministic output jitter | DJ | 10 | 20 | ps p-p | Control bit EQENB = 0, K28.5 pattern at 11.3 Gbps, maximum equalization with 300-mm FR4 trace | 12 | |
| Random output jitter | RJ | 0.5 | 0.8 | ps RMS | 50-Ω load | 12 | |
| Transmitter disable time | tOFF | 1 | 5 | µs | Rising edge of DIS to IBIAS ≤ 0.1 × IBIAS-NOMINAL | 12 | |
| Power-on to initialize | tINIT1 | 1 | 10 | ms | Power-on to registers ready to be loaded | 12 | |
| Modulation current step size | IMOD-STEP | 175 | µA | Control bit MODR = 1, 50-Ω load | 12 | ||
| Modulation current step size | IMOD-STEP | 100 | µA | Control bit MODR = 0, 50-Ω load | 12 | ||
| APC time constant | τAPC | 200 | µs | CAPC = 0.01 µF, IPD = 100 µA, PD coupling ratio CR = 40 | 12 | ||
| Disable negate time | tON | 1 | ms | Falling edge of DIS to IBIAS ≥ 0.9 × IBIAS-NOMINAL | 12 | ||
| Register load STOP command to part ready to transmit valid data | tINIT2 | 2 | ms | 12 | |||
| DIS pulse duration | tRESET | 100 | ns | Time DIS must be held high to reset part | 12 | ||
| Fault assert time | tFAULT | 50 | µs | Time from fault condition to FLT high | 12 |
CAD (KiCad official)
- Symbol:
ONET1191VRGPT - Footprint:
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm - 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
- 3D model files:
onet1191vrgpt-etched.step/onet1191vrgpt-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);onet1191vrgpt.step/onet1191vrgpt.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (26 pp, sha256
1b80b07193e25a7a, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# ONET1191VRGPT
**Texas Instruments** · Laser Drivers · QFN-20(4x4)
ONET1191VRGPT from Texas Instruments, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DIS | input | Disables both bias and modulation currents when set high, and toggling it resets a fault condition. |
| 2 | RZTC | passive | An external zero-TC 28.7-kΩ resistor to ground sets a defined zero-TC reference current for the internal DACs. |
| 3 | TS | output | Temperature sensor output, not buffered and drives capacitive loads only, with VTS = 8.2 mV/°C × TEMP + 1140 mV. |
| 4 | SCK | input | Two-wire interface serial clock input with a 100-kΩ pullup resistor to VCC. |
| 5 | SDA | input | Two-wire interface serial data input with a 100-kΩ pullup resistor to VCC. |
| 6 | GND | power_in | Circuit ground. |
| 7 | DIN+ | input | Noninverted data input, on-chip differentially 100-Ω terminated to DIN-, must be ac-coupled. |
| 8 | DIN- | input | Inverted data input, on-chip differentially 100-Ω terminated to DIN+, must be ac-coupled. |
| 9 | GND | power_in | Circuit ground. |
| 10 | FLT | output | Fault detection flag output. |
| 11 | BGV | output | Buffered bandgap voltage with open emitter output, a replica of the RZTC bandgap voltage; use the same 28.7-kΩ resistor to GND as at RZTC for best matching. |
| 12 | MONB | output | Bias current monitor sourcing a 3.3% replica of the bias current; a fault is triggered if the voltage exceeds 1.15 V, and about 0.8 V at the maximum desired bias current is typical. |
| 13 | MONP | output | Photodiode current monitor sourcing a 50% replica when PDR = 1 and a 250% replica when PDR = 0, with an external resistor (5 kΩ typical) to ground. |
| 14 | COMP | passive | Compensation pin controlling the APC loop bandwidth, requiring a 0.01-µF capacitor to ground. |
| 15 | PD | passive | Photodiode input that sources or sinks current depending on PDP and supplies >1.5 V reverse bias. |
| 16 | BIAS | passive | Sinks average VCSEL bias current in APC and open-loop modes and connects to the laser cathode through an inductor (BLM15HG102SN1D recommended). |
| 17 | VCC | power_in | Supply pin for the 3.3-V ±10% supply voltage. |
| 18 | MOD- | output | Inverted modulation current output, on-chip 55-Ω back-terminated to VCC. |
| 19 | MOD+ | output | Noninverted modulation current output, on-chip 55-Ω back-terminated to VCC. |
| 20 | VCC | power_in | Supply pin for the 3.3-V ±10% supply voltage. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | QFN-20(4x4) |
| Category | Power Supply Chip |
| Pins | 21 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | -0.3 | | 4 | V | | 9 |
| Voltage at DIS, RZTC, TS, SCK, SDA, DIN+, DIN-, FLT, BGV, MONB, MONP, CAPC, PD, BIAS, MOD+, MOD- | | -0.3 | | 4 | V | Respect to network ground | 9 |
| ESD rating at all pins | | | | 2 | kV | HBM | 9 |
| Maximum junction temperature | TJ,max | | | 125 | °C | | 9 |
| Storage temperature range | Tstg | -65 | | 85 | °C | | 9 |
| Lead temperature | TLEAD | | | 260 | °C | 1.6 mm (1/16 inch) from case for 10 seconds | 9 |
| Supply voltage | VCC | 2.9 | 3.3 | 3.6 | V | | 10 |
| Digital input high voltage | VIH | | | 2 | V | DIS, SCK, SDA | 10 |
| Digital input low voltage | VIL | | | 0.8 | V | DIS, SCK, SDA | 10 |
| Bias output headroom voltage | VBIAS - GND | | | 300 | mV | | 10 |
| Photodiode current range | | 12 | | 640 | µA | Control bit PDR = 1, step size = 2.5 µA | 10 |
| Photodiode current range | | 2.5 | | 128 | µA | Control bit PDR = 0, step size = 0.5 µA | 10 |
| Zero-TC resistor value | RRZTC | 28.4 | 28.7 | 29 | kΩ | 1.15-V bandgap bias across resistor | 10 |
| Differential input voltage swing | VIN | 200 | | 1200 | mVp-p | Control bit EQENA = 1 | 10 |
| Differential input voltage swing | VIN | 500 | | 1200 | mVp-p | Control bit EQENA = 0 | 10 |
| Input rise time | tR-IN | 30 | | 55 | ps | 20%-80% | 10 |
| Input fall time | tF-IN | 30 | | 55 | ps | 20%-80% | 10 |
| Operating free-air temperature | TA | -40 | | 85 | °C | | 10 |
| Supply current | IVCC | 62 | | 71 | mA | IMODC = 24 mA, IBIASC = 6 mA, including IMODC and IBIASC, EQENB = 1 | 11 |
| Supply current | IVCC | 70 | | | mA | IMODC = 24 mA, IBIASC = 6 mA, including IMODC and IBIASC, EQENB = 0 | 11 |
| Supply current disabled | IVCC | 35 | | 42 | mA | Disabled, DIS = high and/or control bit ENA = low, EQENB = 1 | 11 |
| Data input resistance | RIN | 85 | 100 | 125 | Ω | Differential between DIN+/DIN- | 11 |
| Data output resistance | ROUT | 45 | 55 | 65 | Ω | Single-ended to VCC | 11 |
| Digital input current | | -50 | | 10 | µA | SCK, SDA, 100-kΩ pullup to VCC | 11 |
| Digital input current | | -10 | | 10 | µA | DIS | 11 |
| Digital output high voltage | VOH | 2.4 | | | V | FLT, ISOURCE = 500 µA | 11 |
| Digital output low voltage | VOL | | | 0.4 | V | FLT, ISINK = 500 µA | 11 |
| Bias current during disable | IBIAS-DIS | | | 100 | µA | | 11 |
| Minimum bias current | IBIAS-MIN | | | 0.2 | mA | See (2) | 11 |
| Maximum bias current | IBIAS-MAX | 14 | | 20 | mA | DAC set to maximum, open- and closed-loop | 11 |
| Photodiode reverse bias voltage | VPD | 1.5 | | 2.3 | V | APC active, IPD = max | 11 |
| Temperature sensor voltage range | VTS | 0.5 | | 2.5 | V | Capacitive load only, with midscale calibration | 11 |
| Temperature sensor accuracy | | -3 | | 3 | °C | With midscale calibration | 11 |
| Temperature sensor drive current | ITS | -1 | | 1 | µA | Source or sink | 11 |
| Photodiode current monitor ratio IMONP/IPD | | 40 | 50 | 60 | % | Control bit PDR = 1 | 11 |
| Photodiode current monitor ratio IMONP/IPD | | 200 | 265 | 300 | % | Control bit PDR = 0 | 11 |
| Bias current monitor ratio IMONB/IBIAS | | 2.7 | 3.3 | 4 | % | 1.2-kΩ sense resistor; nominal 1/30 = 3.3% | 11 |
| VCC reset threshold voltage | VCC-RST | 2.4 | 2.5 | 2.8 | V | VCC voltage level which triggers power-on reset | 11 |
| VCC reset threshold hysteresis | VCC-RSTHYS | | 100 | | mV | | 11 |
| Fault voltage at MONB | VMONB-FLT | 1.05 | 1.15 | 1.25 | V | Fault occurs if voltage at MONB exceeds value | 11 |
| Output rise time | tr-OUT | 20 | | 30 | ps | 20%-80%, tr-IN < 40 ps, 50-Ω load | 12 |
| Output fall time | tf-OUT | 25 | | 30 | ps | 20%-80%, tf-IN < 40 ps, 50-Ω load | 12 |
| Maximum modulation current | IMOD-MAX | 36 | | 45 | mA | Control bit MODR = 1, 50-Ω load | 12 |
| Maximum modulation current | IMOD-MAX | 18 | | 27 | mA | Control bit MODR = 0, 50-Ω load | 12 |
| Deterministic output jitter | DJ | 4 | | 12 | ps p-p | Control bit EQENB = 1, K28.5 pattern at 11.3 Gbps | 12 |
| Deterministic output jitter | DJ | 10 | | 20 | ps p-p | Control bit EQENB = 0, K28.5 pattern at 11.3 Gbps, maximum equalization with 300-mm FR4 trace | 12 |
| Random output jitter | RJ | 0.5 | | 0.8 | ps RMS | 50-Ω load | 12 |
| Transmitter disable time | tOFF | 1 | | 5 | µs | Rising edge of DIS to IBIAS ≤ 0.1 × IBIAS-NOMINAL | 12 |
| Power-on to initialize | tINIT1 | 1 | | 10 | ms | Power-on to registers ready to be loaded | 12 |
| Modulation current step size | IMOD-STEP | | 175 | | µA | Control bit MODR = 1, 50-Ω load | 12 |
| Modulation current step size | IMOD-STEP | | 100 | | µA | Control bit MODR = 0, 50-Ω load | 12 |
| APC time constant | τAPC | | 200 | | µs | CAPC = 0.01 µF, IPD = 100 µA, PD coupling ratio CR = 40 | 12 |
| Disable negate time | tON | | 1 | | ms | Falling edge of DIS to IBIAS ≥ 0.9 × IBIAS-NOMINAL | 12 |
| Register load STOP command to part ready to transmit valid data | tINIT2 | | 2 | | ms | | 12 |
| DIS pulse duration | tRESET | | 100 | | ns | Time DIS must be held high to reset part | 12 |
| Fault assert time | tFAULT | | 50 | | µs | Time from fault condition to FLT high | 12 |
## CAD (KiCad official)
- Symbol: `ONET1191VRGPT`
- Footprint: `Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm`
- 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
- 3D model files: `onet1191vrgpt-etched.step` / `onet1191vrgpt-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `onet1191vrgpt.step` / `onet1191vrgpt.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/onet1191vrgpt.pdf) (26 pp, sha256 `1b80b07193e25a7a`, retrieved 2026-10-28, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/onet1191vrgpt-datasheet.pdf)