Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

ONET1191VRGPT

Texas Instruments · Laser Drivers · QFN-20(4x4)

ONET1191VRGPT from Texas Instruments, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 DIS input Disables both bias and modulation currents when set high, and toggling it resets a fault condition.
2 RZTC passive An external zero-TC 28.7-kΩ resistor to ground sets a defined zero-TC reference current for the internal DACs.
3 TS output Temperature sensor output, not buffered and drives capacitive loads only, with VTS = 8.2 mV/°C × TEMP + 1140 mV.
4 SCK input Two-wire interface serial clock input with a 100-kΩ pullup resistor to VCC.
5 SDA input Two-wire interface serial data input with a 100-kΩ pullup resistor to VCC.
6 GND power_in Circuit ground.
7 DIN+ input Noninverted data input, on-chip differentially 100-Ω terminated to DIN-, must be ac-coupled.
8 DIN- input Inverted data input, on-chip differentially 100-Ω terminated to DIN+, must be ac-coupled.
9 GND power_in Circuit ground.
10 FLT output Fault detection flag output.
11 BGV output Buffered bandgap voltage with open emitter output, a replica of the RZTC bandgap voltage; use the same 28.7-kΩ resistor to GND as at RZTC for best matching.
12 MONB output Bias current monitor sourcing a 3.3% replica of the bias current; a fault is triggered if the voltage exceeds 1.15 V, and about 0.8 V at the maximum desired bias current is typical.
13 MONP output Photodiode current monitor sourcing a 50% replica when PDR = 1 and a 250% replica when PDR = 0, with an external resistor (5 kΩ typical) to ground.
14 COMP passive Compensation pin controlling the APC loop bandwidth, requiring a 0.01-µF capacitor to ground.
15 PD passive Photodiode input that sources or sinks current depending on PDP and supplies >1.5 V reverse bias.
16 BIAS passive Sinks average VCSEL bias current in APC and open-loop modes and connects to the laser cathode through an inductor (BLM15HG102SN1D recommended).
17 VCC power_in Supply pin for the 3.3-V ±10% supply voltage.
18 MOD- output Inverted modulation current output, on-chip 55-Ω back-terminated to VCC.
19 MOD+ output Noninverted modulation current output, on-chip 55-Ω back-terminated to VCC.
20 VCC power_in Supply pin for the 3.3-V ±10% supply voltage.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package QFN-20(4x4)
Category Power Supply Chip
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC -0.3 4 V 9
Voltage at DIS, RZTC, TS, SCK, SDA, DIN+, DIN-, FLT, BGV, MONB, MONP, CAPC, PD, BIAS, MOD+, MOD- -0.3 4 V Respect to network ground 9
ESD rating at all pins 2 kV HBM 9
Maximum junction temperature TJ,max 125 °C 9
Storage temperature range Tstg -65 85 °C 9
Lead temperature TLEAD 260 °C 1.6 mm (1/16 inch) from case for 10 seconds 9
Supply voltage VCC 2.9 3.3 3.6 V 10
Digital input high voltage VIH 2 V DIS, SCK, SDA 10
Digital input low voltage VIL 0.8 V DIS, SCK, SDA 10
Bias output headroom voltage VBIAS - GND 300 mV 10
Photodiode current range 12 640 µA Control bit PDR = 1, step size = 2.5 µA 10
Photodiode current range 2.5 128 µA Control bit PDR = 0, step size = 0.5 µA 10
Zero-TC resistor value RRZTC 28.4 28.7 29 kΩ 1.15-V bandgap bias across resistor 10
Differential input voltage swing VIN 200 1200 mVp-p Control bit EQENA = 1 10
Differential input voltage swing VIN 500 1200 mVp-p Control bit EQENA = 0 10
Input rise time tR-IN 30 55 ps 20%-80% 10
Input fall time tF-IN 30 55 ps 20%-80% 10
Operating free-air temperature TA -40 85 °C 10
Supply current IVCC 62 71 mA IMODC = 24 mA, IBIASC = 6 mA, including IMODC and IBIASC, EQENB = 1 11
Supply current IVCC 70 mA IMODC = 24 mA, IBIASC = 6 mA, including IMODC and IBIASC, EQENB = 0 11
Supply current disabled IVCC 35 42 mA Disabled, DIS = high and/or control bit ENA = low, EQENB = 1 11
Data input resistance RIN 85 100 125 Ω Differential between DIN+/DIN- 11
Data output resistance ROUT 45 55 65 Ω Single-ended to VCC 11
Digital input current -50 10 µA SCK, SDA, 100-kΩ pullup to VCC 11
Digital input current -10 10 µA DIS 11
Digital output high voltage VOH 2.4 V FLT, ISOURCE = 500 µA 11
Digital output low voltage VOL 0.4 V FLT, ISINK = 500 µA 11
Bias current during disable IBIAS-DIS 100 µA 11
Minimum bias current IBIAS-MIN 0.2 mA See (2) 11
Maximum bias current IBIAS-MAX 14 20 mA DAC set to maximum, open- and closed-loop 11
Photodiode reverse bias voltage VPD 1.5 2.3 V APC active, IPD = max 11
Temperature sensor voltage range VTS 0.5 2.5 V Capacitive load only, with midscale calibration 11
Temperature sensor accuracy -3 3 °C With midscale calibration 11
Temperature sensor drive current ITS -1 1 µA Source or sink 11
Photodiode current monitor ratio IMONP/IPD 40 50 60 % Control bit PDR = 1 11
Photodiode current monitor ratio IMONP/IPD 200 265 300 % Control bit PDR = 0 11
Bias current monitor ratio IMONB/IBIAS 2.7 3.3 4 % 1.2-kΩ sense resistor; nominal 1/30 = 3.3% 11
VCC reset threshold voltage VCC-RST 2.4 2.5 2.8 V VCC voltage level which triggers power-on reset 11
VCC reset threshold hysteresis VCC-RSTHYS 100 mV 11
Fault voltage at MONB VMONB-FLT 1.05 1.15 1.25 V Fault occurs if voltage at MONB exceeds value 11
Output rise time tr-OUT 20 30 ps 20%-80%, tr-IN < 40 ps, 50-Ω load 12
Output fall time tf-OUT 25 30 ps 20%-80%, tf-IN < 40 ps, 50-Ω load 12
Maximum modulation current IMOD-MAX 36 45 mA Control bit MODR = 1, 50-Ω load 12
Maximum modulation current IMOD-MAX 18 27 mA Control bit MODR = 0, 50-Ω load 12
Deterministic output jitter DJ 4 12 ps p-p Control bit EQENB = 1, K28.5 pattern at 11.3 Gbps 12
Deterministic output jitter DJ 10 20 ps p-p Control bit EQENB = 0, K28.5 pattern at 11.3 Gbps, maximum equalization with 300-mm FR4 trace 12
Random output jitter RJ 0.5 0.8 ps RMS 50-Ω load 12
Transmitter disable time tOFF 1 5 µs Rising edge of DIS to IBIAS ≤ 0.1 × IBIAS-NOMINAL 12
Power-on to initialize tINIT1 1 10 ms Power-on to registers ready to be loaded 12
Modulation current step size IMOD-STEP 175 µA Control bit MODR = 1, 50-Ω load 12
Modulation current step size IMOD-STEP 100 µA Control bit MODR = 0, 50-Ω load 12
APC time constant τAPC 200 µs CAPC = 0.01 µF, IPD = 100 µA, PD coupling ratio CR = 40 12
Disable negate time tON 1 ms Falling edge of DIS to IBIAS ≥ 0.9 × IBIAS-NOMINAL 12
Register load STOP command to part ready to transmit valid data tINIT2 2 ms 12
DIS pulse duration tRESET 100 ns Time DIS must be held high to reset part 12
Fault assert time tFAULT 50 µs Time from fault condition to FLT high 12

CAD (KiCad official)

  • Symbol: ONET1191VRGPT
  • Footprint: Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm
  • 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
  • 3D model files: onet1191vrgpt-etched.step / onet1191vrgpt-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); onet1191vrgpt.step / onet1191vrgpt.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (26 pp, sha256 1b80b07193e25a7a, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF