3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownNJU7116F-TE1
JRC · Comparators · SOT-23-5
NJU7116F-TE1 from JRC, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN- | input | Inverting comparator input; common mode input voltage range is 0 to 2.5V at VDD=3.0V and absolute maximum is -0.3 to 7V. |
| 2 | VSS | power_in | Negative supply (ground) pin; connect a decoupling capacitor between VDD and VSS. |
| 3 | IN+ | input | Non-inverting comparator input; common mode input voltage range is 0 to 2.5V at VDD=3.0V and absolute maximum is -0.3 to 7V. |
| 4 | OUT | output | CMOS push-pull comparator output with VOH of at least 2.7V at IOH=2mA and VOL of at most 0.3V at IOL=-2mA at VDD=3.0V. |
| 5 | VDD | power_in | Positive supply pin; operating range is 1.8V to 3.6V with an absolute maximum of 7V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | JRC |
| Package | SOT-23-5 |
| Category | Operational Amplifier/Comparator |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Voltage | VDD | 1.8 | 3.6 | V | Ta=25°C, VDD=3.0V, RL=∞ | 2 | |
| Input Offset Voltage | VIO | 2.5 | mV | VIN=1/2VDD | 2 | ||
| High Level Output Voltage | VOH | 2.7 | V | IOH=2mA | 2 | ||
| Low Level Output Voltage | VOL | 0.3 | V | IOL=-2mA | 2 | ||
| Common Mode Rejection Ratio | CMR | 50 | dB | VIC=1/2VDD | 2 | ||
| Supply Voltage Rejection Ratio | SVR | 50 | dB | VDD=1.8~3.6V | 2 | ||
| Operating Current | IDD | 1 | 1.5 | μA | No Load,VO=0V | 2 | |
| Propagation Delay High to Low | tPHL | 1.2 | 2 | μs | Over Drive=100mV, VIC=0V, f=1kHz, CL=15pF | 2 | |
| Propagation Delay Low to High | tPLH | 3.3 | 5 | μs | Over Drive=100mV, VIC=0V, f=1kHz, CL=15pF | 2 | |
| Propagation Delay Time Lag | tPD | 2.1 | 3 | μs | tPLH- tPHL | 2 | |
| Supply Voltage | VDD | 7 | V | Ta=25°C | 2 | ||
| Differential Input Voltage | VID | -7 | 7 | V | Ta=25°C; for supply voltage less than 7V, rating equals supply voltage | 2 | |
| Common Mode Input Voltage | VIC | -0.3 | 7 | V | Ta=25°C; for supply voltage less than 7V, rating equals supply voltage | 2 | |
| Power Dissipation SOT-23-5 (2-layer board) | PD | 390 | mW | EIA/JEDEC test board 2 layers FR-4 | 2 | ||
| Power Dissipation SOT-23-5 (4-layer board) | PD | 520 | mW | EIA/JEDEC test board 4 layers FR-4 | 2 | ||
| Operating Temperature Range | Topr | -40 | 105 | °C | 2 | ||
| Storage Temperature Range | Tstg | -55 | 125 | °C | 2 | ||
| Input Common Mode Voltage Range | VICM | 0 | 2.5 | V | printed 0~2.5 | 2 | |
| Input Offset Current | IIO | 1 | pA | 2 | |||
| Input Bias Current | IIB | 1 | pA | 2 | |||
| Output Signal Falling Time | tTHL | 15 | ns | Over Drive=100mV | 2 | ||
| Output Signal Rising Time | tTLH | 40 | ns | Over Drive=100mV | 2 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
NJU7116F-TE1 - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-23-5, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.1 mm tall, datasheet A, nominal). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
nju7116f-te1-etched.step/nju7116f-te1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);nju7116f-te1.step/nju7116f-te1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: JRC datasheet (7 pp, sha256
84100a36de6dab1e, retrieved 2026-11-12, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).