main
Ray
Publish 0.1.0
51f8146
NCV887300D1R2G
onsemi · DC-DC Converters · SOIC-8
NCV887300D1R2G from onsemi, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN/SYNC | input | Enable and synchronization input whose falling edge synchronizes the internal oscillator, and the part is disabled into sleep mode when this pin is held low longer than the enable time-out period. |
| 2 | ISNS | input | Current sense input connected to the source of the external N-MOSFET through a current-sense resistor to ground, used for regulation and current limiting, with current limit threshold voltage Vcl of 200 mV typical for YY=02. |
| 3 | GND | power_in | Ground reference for the device. |
| 4 | GDRV | output | Gate driver output connected to the gate of the external N-MOSFET, with an optional series resistance from GDRV to the gate to tailor EMC performance; the absolute maximum DC supply voltage for GDRV is 12 V. |
| 5 | VDRV | power_out | Internally regulated driving voltage for the external N-MOSFET sourced from VIN, which must be bypassed with a 1.0 µF ceramic capacitor to ground; the driving voltage is 6.3 V typical for YY=02. |
| 6 | VIN | power_in | Input voltage with an absolute maximum DC supply of 40 V and a 45 V load dump peak transient rating; a diode from the input supply to VIN is needed if bootstrapping operation is desired. |
| 7 | VC | output | Output of the voltage error amplifier, to which an external compensator network from VC to GND is connected to stabilize the converter. |
| 8 | VFB | input | Output voltage feedback input, where a resistor divider from the output to VFB and VFB to GND sets regulation with a 0.200 V reference voltage typical. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Quiescent Current, Sleep Mode | Iq,sleep | 2 | 6 | A | VIN = 13.2 V, EN = 0, -40C < TJ < 125C | 4 | |
| Quiescent Current, No switching | Iq,off | 1.5 | 2.5 | mA | Into VIN pin, EN = 1, No switching | 4 | |
| Quiescent Current, Switching, normal operation | Iq,on | 4 | 6 | mA | Into VIN pin, EN = 1, Switching | 4 | |
| Minimum pulse width | ton,min | 90 | 115 | 140 | ns | 4 | |
| Soft-start delay | tss,dly | 240 | 280 | s | From EN to start of switching with VFB = 0 with floating VC pin | 4 | |
| EN/SYNC pull-down current | IEN/SYNC | 5 | 10 | A | VEN/SYNC = 5 V | 4 | |
| EN/SYNC input high voltage | Vs,ih | 2 | 5 | V | VIN > VUVLO | 4 | |
| EN/SYNC input low voltage | Vs,il | 0 | 800 | mV | 4 | ||
| EN/SYNC time-out ratio | %ten | 350 | % | From SYNC falling edge, to oscillator control (EN high) or shutdown (EN low), Percent of typical switching frequency | 4 | ||
| SYNC minimum frequency ratio | %fsync,min | 80 | % | Percent of fs | 4 | ||
| SYNC maximum frequency | fsync,max | 1.1 | MHz | 4 | |||
| Synchronization delay | ts,dly | 50 | 100 | ns | From SYNC falling edge to GDRV falling edge under open loop conditions | 4 | |
| Synchronization duty cycle | Dsync | 25 | 75 | % | 4 | ||
| Low-frequency gain | Acsa | 0.9 | 1 | 1.1 | V/V | Input-to-output gain at dc, ISNS 1 V | 4 |
| Bandwidth | BWcsa | 2.5 | MHz | Gain of Acsa, -3 dB | 4 | ||
| ISNS input bias current | Isns,bias | 30 | 50 | A | Out of ISNS pin | 4 | |
| Current limit, Response time | tcl | 80 | 125 | ns | CL tripped until GDRV falling edge, VISNS = Vcl(typ) + 60 mV | 4 | |
| Overcurrent protection, Threshold voltage | %Vocp | 125 | 150 | 175 | % | Percent of Vcl | 4 |
| Overcurrent protection, Response Time | tocp | 80 | 125 | ns | From overcurrent event, until switching stops, VISNS = VOCP + 40 mV | 4 | |
| Transconductance | gm,vea | 0.8 | 1.2 | 1.63 | mS | VFB - Vref = +/- 20 mV | 4 |
| VEA output resistance | Ro,vea | 2 | M | 4 | |||
| VFB input bias current | Ivfb,bias | 0.5 | 2 | A | Current out of VFB pin | 4 | |
| Reference voltage | Vref | 0.194 | 0.2 | 0.206 | V | 4 | |
| VEA maximum output voltage | Vc,max | 2.5 | V | 5 | |||
| VEA minimum output voltage | Vc,min | 0.3 | V | 5 | |||
| VEA sourcing current | Isrc,vea | 80 | 100 | A | VEA output current, Vc = 2.0 V | 5 | |
| VEA sinking current | Isnk,vea | 80 | 100 | A | VEA output current, Vc = 0.7 V | 5 | |
| Driving voltage dropout | Vdrv,do | 0.3 | 0.6 | V | VIN - VDRV, IvDRV = 25 mA | 5 | |
| Driving voltage source current | Idrv | 35 | 45 | mA | VIN - VDRV = 1 V | 5 | |
| Backdrive diode voltage drop | Vd,bd | 0.7 | V | VDRV - VIN, Id,bd = 5 mA | 5 | ||
| Undervoltage lock-out, Threshold voltage | Vuvlo | 2.95 | 3.05 | 3.15 | V | VIN falling | 5 |
| Undervoltage lock-out, Hysteresis | Vuvlo,hys | 50 | 150 | 250 | mV | VIN rising | 5 |
| Thermal shutdown threshold | Tsd | 160 | 170 | 180 | C | TJ rising | 5 |
| Thermal shutdown hysteresis | Tsd,hys | 10 | 15 | 20 | C | TJ falling | 5 |
| Thermal shutdown delay | tsd,dly | 100 | ns | From TJ > Tsd to stop switching | 5 | ||
| DC Supply Voltage | VIN | -0.3 | 40 | V | 3 | ||
| Peak Transient Voltage (Load Dump) | 45 | V | Load Dump on VIN | 3 | |||
| DC Supply Voltage (VDRV, GDRV) | 12 | V | 3 | ||||
| Peak Transient Voltage (VFB) | VFB | -0.3 | 6 | V | Peak transient | 3 | |
| DC Voltage (VC, VFB, ISNS) | VC, VFB, ISNS | -0.3 | 3.6 | V | 3 | ||
| DC Voltage (EN/SYNC) | EN/SYNC | -0.3 | 6 | V | 3 | ||
| DC Voltage Stress (VIN - VDRV) | VIN - VDRV | -0.7 | 40 | V | Footnote: external diode from input to VIN required if bootstrapping | 3 | |
| Operating Junction Temperature | TJ | -40 | 150 | C | 3 | ||
| Storage Temperature Range | Tstg | -65 | 150 | C | 3 | ||
| Peak Reflow Soldering Temperature | 265 | C | Pb-Free, 60 to 150 seconds at 217C | 3 | |||
| Package Thermal Resistance Junction-to-Ambient | RthJA | 100 | C/W | 1 in2, 1 oz copper area used for heatsinking | 3 |
CAD (KiCad official)
- Symbol:
NCV887300D1R2G - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
ncv887300d1r2g-etched.step/ncv887300d1r2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncv887300d1r2g.step/ncv887300d1r2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (13 pp, sha256
627c4711ab9a3914, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# NCV887300D1R2G
**onsemi** · DC-DC Converters · SOIC-8
NCV887300D1R2G from onsemi, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN/SYNC | input | Enable and synchronization input whose falling edge synchronizes the internal oscillator, and the part is disabled into sleep mode when this pin is held low longer than the enable time-out period. |
| 2 | ISNS | input | Current sense input connected to the source of the external N-MOSFET through a current-sense resistor to ground, used for regulation and current limiting, with current limit threshold voltage Vcl of 200 mV typical for YY=02. |
| 3 | GND | power_in | Ground reference for the device. |
| 4 | GDRV | output | Gate driver output connected to the gate of the external N-MOSFET, with an optional series resistance from GDRV to the gate to tailor EMC performance; the absolute maximum DC supply voltage for GDRV is 12 V. |
| 5 | VDRV | power_out | Internally regulated driving voltage for the external N-MOSFET sourced from VIN, which must be bypassed with a 1.0 µF ceramic capacitor to ground; the driving voltage is 6.3 V typical for YY=02. |
| 6 | VIN | power_in | Input voltage with an absolute maximum DC supply of 40 V and a 45 V load dump peak transient rating; a diode from the input supply to VIN is needed if bootstrapping operation is desired. |
| 7 | VC | output | Output of the voltage error amplifier, to which an external compensator network from VC to GND is connected to stabilize the converter. |
| 8 | VFB | input | Output voltage feedback input, where a resistor divider from the output to VFB and VFB to GND sets regulation with a 0.200 V reference voltage typical. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-8 |
| Category | Power Supply Chip |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Quiescent Current, Sleep Mode | Iq,sleep | | 2 | 6 | A | VIN = 13.2 V, EN = 0, -40C < TJ < 125C | 4 |
| Quiescent Current, No switching | Iq,off | | 1.5 | 2.5 | mA | Into VIN pin, EN = 1, No switching | 4 |
| Quiescent Current, Switching, normal operation | Iq,on | | 4 | 6 | mA | Into VIN pin, EN = 1, Switching | 4 |
| Minimum pulse width | ton,min | 90 | 115 | 140 | ns | | 4 |
| Soft-start delay | tss,dly | | 240 | 280 | s | From EN to start of switching with VFB = 0 with floating VC pin | 4 |
| EN/SYNC pull-down current | IEN/SYNC | | 5 | 10 | A | VEN/SYNC = 5 V | 4 |
| EN/SYNC input high voltage | Vs,ih | 2 | | 5 | V | VIN > VUVLO | 4 |
| EN/SYNC input low voltage | Vs,il | 0 | | 800 | mV | | 4 |
| EN/SYNC time-out ratio | %ten | | | 350 | % | From SYNC falling edge, to oscillator control (EN high) or shutdown (EN low), Percent of typical switching frequency | 4 |
| SYNC minimum frequency ratio | %fsync,min | | | 80 | % | Percent of fs | 4 |
| SYNC maximum frequency | fsync,max | 1.1 | | | MHz | | 4 |
| Synchronization delay | ts,dly | | 50 | 100 | ns | From SYNC falling edge to GDRV falling edge under open loop conditions | 4 |
| Synchronization duty cycle | Dsync | 25 | | 75 | % | | 4 |
| Low-frequency gain | Acsa | 0.9 | 1 | 1.1 | V/V | Input-to-output gain at dc, ISNS 1 V | 4 |
| Bandwidth | BWcsa | 2.5 | | | MHz | Gain of Acsa, -3 dB | 4 |
| ISNS input bias current | Isns,bias | | 30 | 50 | A | Out of ISNS pin | 4 |
| Current limit, Response time | tcl | | 80 | 125 | ns | CL tripped until GDRV falling edge, VISNS = Vcl(typ) + 60 mV | 4 |
| Overcurrent protection, Threshold voltage | %Vocp | 125 | 150 | 175 | % | Percent of Vcl | 4 |
| Overcurrent protection, Response Time | tocp | | 80 | 125 | ns | From overcurrent event, until switching stops, VISNS = VOCP + 40 mV | 4 |
| Transconductance | gm,vea | 0.8 | 1.2 | 1.63 | mS | VFB - Vref = +/- 20 mV | 4 |
| VEA output resistance | Ro,vea | 2 | | | M | | 4 |
| VFB input bias current | Ivfb,bias | | 0.5 | 2 | A | Current out of VFB pin | 4 |
| Reference voltage | Vref | 0.194 | 0.2 | 0.206 | V | | 4 |
| VEA maximum output voltage | Vc,max | 2.5 | | | V | | 5 |
| VEA minimum output voltage | Vc,min | | | 0.3 | V | | 5 |
| VEA sourcing current | Isrc,vea | 80 | 100 | | A | VEA output current, Vc = 2.0 V | 5 |
| VEA sinking current | Isnk,vea | 80 | 100 | | A | VEA output current, Vc = 0.7 V | 5 |
| Driving voltage dropout | Vdrv,do | | 0.3 | 0.6 | V | VIN - VDRV, IvDRV = 25 mA | 5 |
| Driving voltage source current | Idrv | 35 | 45 | | mA | VIN - VDRV = 1 V | 5 |
| Backdrive diode voltage drop | Vd,bd | | | 0.7 | V | VDRV - VIN, Id,bd = 5 mA | 5 |
| Undervoltage lock-out, Threshold voltage | Vuvlo | 2.95 | 3.05 | 3.15 | V | VIN falling | 5 |
| Undervoltage lock-out, Hysteresis | Vuvlo,hys | 50 | 150 | 250 | mV | VIN rising | 5 |
| Thermal shutdown threshold | Tsd | 160 | 170 | 180 | C | TJ rising | 5 |
| Thermal shutdown hysteresis | Tsd,hys | 10 | 15 | 20 | C | TJ falling | 5 |
| Thermal shutdown delay | tsd,dly | | | 100 | ns | From TJ > Tsd to stop switching | 5 |
| DC Supply Voltage | VIN | -0.3 | | 40 | V | | 3 |
| Peak Transient Voltage (Load Dump) | | | | 45 | V | Load Dump on VIN | 3 |
| DC Supply Voltage (VDRV, GDRV) | | | | 12 | V | | 3 |
| Peak Transient Voltage (VFB) | VFB | -0.3 | | 6 | V | Peak transient | 3 |
| DC Voltage (VC, VFB, ISNS) | VC, VFB, ISNS | -0.3 | | 3.6 | V | | 3 |
| DC Voltage (EN/SYNC) | EN/SYNC | -0.3 | | 6 | V | | 3 |
| DC Voltage Stress (VIN - VDRV) | VIN - VDRV | -0.7 | | 40 | V | Footnote: external diode from input to VIN required if bootstrapping | 3 |
| Operating Junction Temperature | TJ | -40 | | 150 | C | | 3 |
| Storage Temperature Range | Tstg | -65 | | 150 | C | | 3 |
| Peak Reflow Soldering Temperature | | | | 265 | C | Pb-Free, 60 to 150 seconds at 217C | 3 |
| Package Thermal Resistance Junction-to-Ambient | RthJA | | 100 | | C/W | 1 in2, 1 oz copper area used for heatsinking | 3 |
## CAD (KiCad official)
- Symbol: `NCV887300D1R2G`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files: `ncv887300d1r2g-etched.step` / `ncv887300d1r2g-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ncv887300d1r2g.step` / `ncv887300d1r2g.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [onsemi datasheet](https://www.onsemi.com/pdf/datasheet/ncv887300d1r2-d.pdf) (13 pp, sha256 `627c4711ab9a3914`, retrieved 2026-11-02, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ncv887300d1r2g-datasheet.pdf)