main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers ncv887300d1r2g: viewers · Ray
ncv887300d1r2g-etched.glb Publish 0.1.0 · Ray
ncv887300d1r2g-etched.step ncv887300d1r2g: factory component page (tier=mfr) · Ray
ncv887300d1r2g-hero.glb ncv887300d1r2g: hero GLB from the etched model (keeps the MPN mark) · Ray
ncv887300d1r2g-hero.overlay.json Publish 0.1.0 · Ray
ncv887300d1r2g.glb Publish 0.1.0 · Ray
ncv887300d1r2g.kicad_mod Publish 0.1.0 · Ray
ncv887300d1r2g.kicad_sym Publish 0.1.0 · Ray
ncv887300d1r2g.lbr Publish 0.1.0 · Ray
ncv887300d1r2g.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 8 pins · Ray

NCV887300D1R2G

onsemi · DC-DC Converters · SOIC-8

NCV887300D1R2G from onsemi, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 EN/SYNC input Enable and synchronization input whose falling edge synchronizes the internal oscillator, and the part is disabled into sleep mode when this pin is held low longer than the enable time-out period.
2 ISNS input Current sense input connected to the source of the external N-MOSFET through a current-sense resistor to ground, used for regulation and current limiting, with current limit threshold voltage Vcl of 200 mV typical for YY=02.
3 GND power_in Ground reference for the device.
4 GDRV output Gate driver output connected to the gate of the external N-MOSFET, with an optional series resistance from GDRV to the gate to tailor EMC performance; the absolute maximum DC supply voltage for GDRV is 12 V.
5 VDRV power_out Internally regulated driving voltage for the external N-MOSFET sourced from VIN, which must be bypassed with a 1.0 µF ceramic capacitor to ground; the driving voltage is 6.3 V typical for YY=02.
6 VIN power_in Input voltage with an absolute maximum DC supply of 40 V and a 45 V load dump peak transient rating; a diode from the input supply to VIN is needed if bootstrapping operation is desired.
7 VC output Output of the voltage error amplifier, to which an external compensator network from VC to GND is connected to stabilize the converter.
8 VFB input Output voltage feedback input, where a resistor divider from the output to VFB and VFB to GND sets regulation with a 0.200 V reference voltage typical.

Key specifications

Parameter Value
Manufacturer onsemi
Package SOIC-8
Category Power Supply Chip
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Quiescent Current, Sleep Mode Iq,sleep 2 6 A VIN = 13.2 V, EN = 0, -40C < TJ < 125C 4
Quiescent Current, No switching Iq,off 1.5 2.5 mA Into VIN pin, EN = 1, No switching 4
Quiescent Current, Switching, normal operation Iq,on 4 6 mA Into VIN pin, EN = 1, Switching 4
Minimum pulse width ton,min 90 115 140 ns 4
Soft-start delay tss,dly 240 280 s From EN to start of switching with VFB = 0 with floating VC pin 4
EN/SYNC pull-down current IEN/SYNC 5 10 A VEN/SYNC = 5 V 4
EN/SYNC input high voltage Vs,ih 2 5 V VIN > VUVLO 4
EN/SYNC input low voltage Vs,il 0 800 mV 4
EN/SYNC time-out ratio %ten 350 % From SYNC falling edge, to oscillator control (EN high) or shutdown (EN low), Percent of typical switching frequency 4
SYNC minimum frequency ratio %fsync,min 80 % Percent of fs 4
SYNC maximum frequency fsync,max 1.1 MHz 4
Synchronization delay ts,dly 50 100 ns From SYNC falling edge to GDRV falling edge under open loop conditions 4
Synchronization duty cycle Dsync 25 75 % 4
Low-frequency gain Acsa 0.9 1 1.1 V/V Input-to-output gain at dc, ISNS 1 V 4
Bandwidth BWcsa 2.5 MHz Gain of Acsa, -3 dB 4
ISNS input bias current Isns,bias 30 50 A Out of ISNS pin 4
Current limit, Response time tcl 80 125 ns CL tripped until GDRV falling edge, VISNS = Vcl(typ) + 60 mV 4
Overcurrent protection, Threshold voltage %Vocp 125 150 175 % Percent of Vcl 4
Overcurrent protection, Response Time tocp 80 125 ns From overcurrent event, until switching stops, VISNS = VOCP + 40 mV 4
Transconductance gm,vea 0.8 1.2 1.63 mS VFB - Vref = +/- 20 mV 4
VEA output resistance Ro,vea 2 M 4
VFB input bias current Ivfb,bias 0.5 2 A Current out of VFB pin 4
Reference voltage Vref 0.194 0.2 0.206 V 4
VEA maximum output voltage Vc,max 2.5 V 5
VEA minimum output voltage Vc,min 0.3 V 5
VEA sourcing current Isrc,vea 80 100 A VEA output current, Vc = 2.0 V 5
VEA sinking current Isnk,vea 80 100 A VEA output current, Vc = 0.7 V 5
Driving voltage dropout Vdrv,do 0.3 0.6 V VIN - VDRV, IvDRV = 25 mA 5
Driving voltage source current Idrv 35 45 mA VIN - VDRV = 1 V 5
Backdrive diode voltage drop Vd,bd 0.7 V VDRV - VIN, Id,bd = 5 mA 5
Undervoltage lock-out, Threshold voltage Vuvlo 2.95 3.05 3.15 V VIN falling 5
Undervoltage lock-out, Hysteresis Vuvlo,hys 50 150 250 mV VIN rising 5
Thermal shutdown threshold Tsd 160 170 180 C TJ rising 5
Thermal shutdown hysteresis Tsd,hys 10 15 20 C TJ falling 5
Thermal shutdown delay tsd,dly 100 ns From TJ > Tsd to stop switching 5
DC Supply Voltage VIN -0.3 40 V 3
Peak Transient Voltage (Load Dump) 45 V Load Dump on VIN 3
DC Supply Voltage (VDRV, GDRV) 12 V 3
Peak Transient Voltage (VFB) VFB -0.3 6 V Peak transient 3
DC Voltage (VC, VFB, ISNS) VC, VFB, ISNS -0.3 3.6 V 3
DC Voltage (EN/SYNC) EN/SYNC -0.3 6 V 3
DC Voltage Stress (VIN - VDRV) VIN - VDRV -0.7 40 V Footnote: external diode from input to VIN required if bootstrapping 3
Operating Junction Temperature TJ -40 150 C 3
Storage Temperature Range Tstg -65 150 C 3
Peak Reflow Soldering Temperature 265 C Pb-Free, 60 to 150 seconds at 217C 3
Package Thermal Resistance Junction-to-Ambient RthJA 100 C/W 1 in2, 1 oz copper area used for heatsinking 3

CAD (KiCad official)

  • Symbol: NCV887300D1R2G
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: ncv887300d1r2g-etched.step / ncv887300d1r2g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncv887300d1r2g.step / ncv887300d1r2g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (13 pp, sha256 627c4711ab9a3914, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF