main
Ray
Publish 0.1.0
5caeae0
NCV57090ADWR2G
onsemi · Gate Drive ICs · SOIC-8-300mil
NCV57090ADWR2G from onsemi, in a SOIC-8-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD1 | power_in | Input-side power supply that needs a good-quality bypass capacitor to GND1 placed close to the pin, and the UVLO1 circuit enables operation only when a typical supply above VUVLO1-OUT-ON (3.1 V max) is present; the operating range is UVLO1 to 20 V. |
| 2 | IN+ | input | Non-inverting gate driver input, internally clamped to GND1 with an internal 125 kΩ pull-down that keeps the output low without an input signal, and a minimum positive or negative pulse width is required before OUT responds. |
| 3 | IN− | input | Inverting gate driver input, internally clamped to VDD1 with an internal 50 kΩ pull-up that keeps the output low without an input signal, and a minimum positive or negative pulse width is required before OUT responds. |
| 4 | GND1 | power_in | Input-side ground reference for the driver. |
| 5 | VDD2 | power_in | Output-side positive power supply with an operating range from UVLO2 to 30 V max, requiring a good-quality bypass capacitor to GND2 placed close to the pin. |
| 6 | OUT | output | Driver output that provides the drive voltage and source/sink current to the IGBT/MOSFET gate (6.5 A peak source and sink) and is actively pulled low during start-up. |
| 7 | CLAMP | output | Active Miller clamp output that turns on its internal N FET when the voltage falls below VCLAMP-THR (1.5 V to 2.5 V) and must be tied directly to the IGBT/MOSFET gate with minimum trace length. |
| 8 | GND2 | power_in | Output-side gate drive reference, connected to the IGBT emitter or MOSFET source. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-8-300mil |
| Category | Power Management ICs |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage, Input Side (VDD1-GND1) | VDD1−GND1 | -0.3 | 22 | V | Over operating free-air temperature range | 6 | |
| Positive Power Supply, Output Side (VDD2-GND2) | VDD2−GND2 | -0.3 | 32 | V | Over operating free-air temperature range | 6 | |
| Gate-driver Output Low Voltage (VOUT-GND2) | VOUT−GND2 | -0.3 | V | NCD57090A/B/D/F | 6 | ||
| Gate-driver Output Sourcing Current | IPK−SRC | 6.5 | A | maximum pulse width = 10 µs, maximum duty cycle = 0.2%, VDD2 = 15 V, VEE2 = 0 V | 6 | ||
| Gate-driver Output Sinking Current | IPK−SNK | 6.5 | A | maximum pulse width = 10 µs, maximum duty cycle = 0.2%, VDD2 = 15 V, VEE2 = 0 V | 6 | ||
| Clamp Sinking Current | IPK−CLAMP | 2.5 | A | maximum pulse width = 10 µs, maximum duty cycle = 0.2%, VCLAMP = 2.5 V | 6 | ||
| Maximum Short Circuit Clamping Time | tCLP | 10 | µs | IOUT_CLAMP = 500 mA | 6 | ||
| Voltage at IN+, IN− | VLIM−GND1 | -0.3 | V | 6 | |||
| Clamp Voltage | VCLAMP−GND2 | -0.3 | V | 6 | |||
| Power Dissipation (SOIC-8 Wide Package) | PD | 1470 | mW | 6 | |||
| Maximum Junction Temperature | TJ(max) | -40 | 150 | °C | 7 | ||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 7 | ||
| ESD Capability, Human Body Model | ESDHBM | -2 | 2 | kV | Human Body Model, AEC-Q100-002 | 7 | |
| ESD Capability, Charged Device Model | ESDCDM | -2 | 2 | kV | Charged Device Model, AEC-Q100-011 | 7 | |
| Lead Temperature Soldering Reflow, Pb-Free | TSLD | 260 | °C | 7 | |||
| Supply Voltage, Input Side (max) | VDD1−GND1 | 20 | V | Minimum is UVLO1 | 7 | ||
| Positive Power Supply, Output Side (max) | VDD2−GND2 | 30 | V | Minimum is UVLO2 | 7 | ||
| Low Level Input Voltage at IN+, IN− | VIL | 0 | V | Values valid for 3.3 V and 5 V VDD1 | 7 | ||
| Common Mode Transient Immunity | /dVISO/dt/ | 100 | kV/µs | Tested by ±1500 V pulses | 7 | ||
| Ambient Temperature | TA | -40 | 125 | °C | 7 | ||
| UVLO1 Output Enabled | VUVLO1−OUT−ON | 3.1 | V | UVLO1 Output Enabled | 9 | ||
| UVLO1 Output Disabled | VUVLO1−OUT−OFF | 2.4 | V | UVLO1 Output Disabled | 9 | ||
| UVLO1 Hysteresis | VUVLO1−HYST | 0.1 | V | 9 | |||
| UVLO2 Output Enabled, NCx57090y | VUVLO2−OUT−ON | 12.4 | 12.9 | 13.4 | V | UVLO2 Output Enabled, NCx57090y | 9 |
| UVLO2 Output Disabled, NCx57090y | VUVLO2−OUT−OFF | 11.5 | 12 | 12.5 | V | UVLO2 Output Disabled, NCx57090y | 9 |
| UVLO2 Hysteresis | VUVLO2−HYST | 0.7 | 1 | V | 9 | ||
| Input Supply Quiescent Current | IDD1−0−3.3 | 2 | mA | IN+ = Low, IN− = Low, VDD1 = 3.3 V | 9 | ||
| Input Supply Current | IDD1−100−5 | 5.5 | mA | IN+ = High, IN− = Low | 9 | ||
| Output Positive Supply Quiescent Current | IDD2−0 | 2 | mA | IN+ = Low, IN− = Low, no load | 9 | ||
| Output Positive Supply Current | IDD2−100 | 2 | mA | IN+ = High, IN− = Low, no load | 9 | ||
| IN− Input Current | IIN−L−3.3 | 100 | µA | VIN− = 0 V, VDD1 = 3.3 V | 9 | ||
| IN+ Input Current | IIN+H−3.3 | 100 | µA | VIN+ = VDD1 = 3.3 V | 9 | ||
| Input Pulse Width for Guaranteed No Response at Output | tON−MIN1 | 10 | ns | Input Pulse Width of IN+, IN− for Guaranteed No Response at Output | 9 | ||
| Input Pulse Width for Guaranteed Response at Output | tON−MIN2 | 40 | ns | Input Pulse Width of IN+, IN− for Guaranteed Response at Output | 9 | ||
| Output Low State (VOUT-GND2, NCD57090A/D/F) | VOUTL1 | 0.15 | 0.3 | V | ISINK = 200 mA | 10 | |
| Output Low State (VOUT-GND2, NCD57090A/D/F) | VOUTL2 | 0.8 | V | ISINK = 1.0 A, TA = 25°C | 10 | ||
| Output High State (VDD2-VOUT, NCD57090A/B/D/F) | VOUTH1 | 0.2 | 0.35 | V | ISRC = 200 mA | 10 | |
| Output High State (VDD2-VOUT, NCD57090A/B/D/F) | VOUTH2 | 1 | V | ISRC = 1.0 A, TA = 25°C | 10 | ||
| Clamp Voltage | VCLAMP | 3.5 | V | ICLAMP = 2.5 A, TA = −40°C to 125°C | 10 | ||
| Clamp Activation Threshold | VCLAMP−THR | 1.5 | 2 | 2.5 | V | 10 | |
| Clamping Voltage, Sourcing (VOUT / VOUTH-VDD2) | VCLAMP−OUTH | 0.7 | 0.9 | V | IN+ = Low, IN− = High, ICLAMP−OUT/OUTH = 500 mA (pulse test, tCLPmax = 10 µs) | 10 | |
| Clamping Voltage, Sinking (VOUTL-VDD2) | VCLAMP−OUTL | 0.8 | 1.5 | V | IN+ = High, IN− = Low, ICLAMP−OUTL = 500 mA (pulse test, tCLPmax = 10 µs) | 10 | |
| Clamping Voltage, Clamp (VCLAMP-VDD2, NCD57090A/D/F) | VCLAMP−CLAMP | 1.1 | 1.7 | V | IN+ = High, IN− = Low, ICLAMP−CLAMP = 500 mA (pulse test, tCLPmax = 10 µs) | 10 | |
| IN+, IN− to Output High Propagation Delay | tPD−ON−3.3 | 40 | 60 | 90 | ns | CLOAD = 10 nF; VDD1 = VIN+ = 3.3V, VIN− = 0 V | 10 |
| IN+, IN− to Output Low Propagation Delay | tPD−OFF−3.3 | 40 | 60 | 90 | ns | CLOAD = 10 nF; VDD1 = VIN+ = 3.3 V, VIN− = 0 V | 10 |
| Propagation Delay Distortion (tPD−ON − tPD−OFF) | tDISTORT | -25 | 25 | ns | TA = −40°C to 125°C, PW > 150 ns | 10 | |
| Prop Delay Distortion between Parts | tDISTORT_TOT | -30 | 0 | 30 | ns | PW > 150 ns | 10 |
| Junction-to-Air Thermal Resistance, SOIC-8 wide body (1-layer) | RJA | 156 | °C/W | 1-Layer PCB, see Note 5 | 7 | ||
| Junction-to-Air Thermal Resistance, SOIC-8 wide body (4-layer) | RJA | 85 | °C/W | 4-Layer PCB, see Note 5 | 7 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | ABS | RIO Insulation Resistance at TS, VIO = 500 V 109 Table 3. ABSOLUTE MAXIMUM RATINGS (Note 1) | 7 |
CAD (KiCad official)
- Symbol:
NCV57090ADWR2G - Footprint:
Package_SO:SOIC-8_7.5x5.85mm_P1.27mm - 3D model: SOIC-8-300mil (KiCad packages3D, STEP)
- 3D model files:
ncv57090adwr2g-etched.step/ncv57090adwr2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncv57090adwr2g.step/ncv57090adwr2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (26 pp, sha256
26abe74476d9160c, retrieved 2026-11-11, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# NCV57090ADWR2G
**onsemi** · Gate Drive ICs · SOIC-8-300mil
NCV57090ADWR2G from onsemi, in a SOIC-8-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD1 | power_in | Input-side power supply that needs a good-quality bypass capacitor to GND1 placed close to the pin, and the UVLO1 circuit enables operation only when a typical supply above VUVLO1-OUT-ON (3.1 V max) is present; the operating range is UVLO1 to 20 V. |
| 2 | IN+ | input | Non-inverting gate driver input, internally clamped to GND1 with an internal 125 kΩ pull-down that keeps the output low without an input signal, and a minimum positive or negative pulse width is required before OUT responds. |
| 3 | IN− | input | Inverting gate driver input, internally clamped to VDD1 with an internal 50 kΩ pull-up that keeps the output low without an input signal, and a minimum positive or negative pulse width is required before OUT responds. |
| 4 | GND1 | power_in | Input-side ground reference for the driver. |
| 5 | VDD2 | power_in | Output-side positive power supply with an operating range from UVLO2 to 30 V max, requiring a good-quality bypass capacitor to GND2 placed close to the pin. |
| 6 | OUT | output | Driver output that provides the drive voltage and source/sink current to the IGBT/MOSFET gate (6.5 A peak source and sink) and is actively pulled low during start-up. |
| 7 | CLAMP | output | Active Miller clamp output that turns on its internal N FET when the voltage falls below VCLAMP-THR (1.5 V to 2.5 V) and must be tied directly to the IGBT/MOSFET gate with minimum trace length. |
| 8 | GND2 | power_in | Output-side gate drive reference, connected to the IGBT emitter or MOSFET source. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-8-300mil |
| Category | Power Management ICs |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage, Input Side (VDD1-GND1) | VDD1−GND1 | -0.3 | | 22 | V | Over operating free-air temperature range | 6 |
| Positive Power Supply, Output Side (VDD2-GND2) | VDD2−GND2 | -0.3 | | 32 | V | Over operating free-air temperature range | 6 |
| Gate-driver Output Low Voltage (VOUT-GND2) | VOUT−GND2 | -0.3 | | | V | NCD57090A/B/D/F | 6 |
| Gate-driver Output Sourcing Current | IPK−SRC | | | 6.5 | A | maximum pulse width = 10 µs, maximum duty cycle = 0.2%, VDD2 = 15 V, VEE2 = 0 V | 6 |
| Gate-driver Output Sinking Current | IPK−SNK | | | 6.5 | A | maximum pulse width = 10 µs, maximum duty cycle = 0.2%, VDD2 = 15 V, VEE2 = 0 V | 6 |
| Clamp Sinking Current | IPK−CLAMP | | | 2.5 | A | maximum pulse width = 10 µs, maximum duty cycle = 0.2%, VCLAMP = 2.5 V | 6 |
| Maximum Short Circuit Clamping Time | tCLP | | | 10 | µs | IOUT_CLAMP = 500 mA | 6 |
| Voltage at IN+, IN− | VLIM−GND1 | -0.3 | | | V | | 6 |
| Clamp Voltage | VCLAMP−GND2 | -0.3 | | | V | | 6 |
| Power Dissipation (SOIC-8 Wide Package) | PD | | | 1470 | mW | | 6 |
| Maximum Junction Temperature | TJ(max) | -40 | | 150 | °C | | 7 |
| Storage Temperature Range | TSTG | -65 | | 150 | °C | | 7 |
| ESD Capability, Human Body Model | ESDHBM | -2 | | 2 | kV | Human Body Model, AEC-Q100-002 | 7 |
| ESD Capability, Charged Device Model | ESDCDM | -2 | | 2 | kV | Charged Device Model, AEC-Q100-011 | 7 |
| Lead Temperature Soldering Reflow, Pb-Free | TSLD | | | 260 | °C | | 7 |
| Supply Voltage, Input Side (max) | VDD1−GND1 | | | 20 | V | Minimum is UVLO1 | 7 |
| Positive Power Supply, Output Side (max) | VDD2−GND2 | | | 30 | V | Minimum is UVLO2 | 7 |
| Low Level Input Voltage at IN+, IN− | VIL | 0 | | | V | Values valid for 3.3 V and 5 V VDD1 | 7 |
| Common Mode Transient Immunity | /dVISO/dt/ | 100 | | | kV/µs | Tested by ±1500 V pulses | 7 |
| Ambient Temperature | TA | -40 | | 125 | °C | | 7 |
| UVLO1 Output Enabled | VUVLO1−OUT−ON | | | 3.1 | V | UVLO1 Output Enabled | 9 |
| UVLO1 Output Disabled | VUVLO1−OUT−OFF | 2.4 | | | V | UVLO1 Output Disabled | 9 |
| UVLO1 Hysteresis | VUVLO1−HYST | 0.1 | | | V | | 9 |
| UVLO2 Output Enabled, NCx57090y | VUVLO2−OUT−ON | 12.4 | 12.9 | 13.4 | V | UVLO2 Output Enabled, NCx57090y | 9 |
| UVLO2 Output Disabled, NCx57090y | VUVLO2−OUT−OFF | 11.5 | 12 | 12.5 | V | UVLO2 Output Disabled, NCx57090y | 9 |
| UVLO2 Hysteresis | VUVLO2−HYST | 0.7 | 1 | | V | | 9 |
| Input Supply Quiescent Current | IDD1−0−3.3 | | | 2 | mA | IN+ = Low, IN− = Low, VDD1 = 3.3 V | 9 |
| Input Supply Current | IDD1−100−5 | | | 5.5 | mA | IN+ = High, IN− = Low | 9 |
| Output Positive Supply Quiescent Current | IDD2−0 | | | 2 | mA | IN+ = Low, IN− = Low, no load | 9 |
| Output Positive Supply Current | IDD2−100 | | | 2 | mA | IN+ = High, IN− = Low, no load | 9 |
| IN− Input Current | IIN−L−3.3 | | | 100 | µA | VIN− = 0 V, VDD1 = 3.3 V | 9 |
| IN+ Input Current | IIN+H−3.3 | | | 100 | µA | VIN+ = VDD1 = 3.3 V | 9 |
| Input Pulse Width for Guaranteed No Response at Output | tON−MIN1 | | | 10 | ns | Input Pulse Width of IN+, IN− for Guaranteed No Response at Output | 9 |
| Input Pulse Width for Guaranteed Response at Output | tON−MIN2 | 40 | | | ns | Input Pulse Width of IN+, IN− for Guaranteed Response at Output | 9 |
| Output Low State (VOUT-GND2, NCD57090A/D/F) | VOUTL1 | | 0.15 | 0.3 | V | ISINK = 200 mA | 10 |
| Output Low State (VOUT-GND2, NCD57090A/D/F) | VOUTL2 | | | 0.8 | V | ISINK = 1.0 A, TA = 25°C | 10 |
| Output High State (VDD2-VOUT, NCD57090A/B/D/F) | VOUTH1 | | 0.2 | 0.35 | V | ISRC = 200 mA | 10 |
| Output High State (VDD2-VOUT, NCD57090A/B/D/F) | VOUTH2 | | | 1 | V | ISRC = 1.0 A, TA = 25°C | 10 |
| Clamp Voltage | VCLAMP | | | 3.5 | V | ICLAMP = 2.5 A, TA = −40°C to 125°C | 10 |
| Clamp Activation Threshold | VCLAMP−THR | 1.5 | 2 | 2.5 | V | | 10 |
| Clamping Voltage, Sourcing (VOUT / VOUTH-VDD2) | VCLAMP−OUTH | | 0.7 | 0.9 | V | IN+ = Low, IN− = High, ICLAMP−OUT/OUTH = 500 mA (pulse test, tCLPmax = 10 µs) | 10 |
| Clamping Voltage, Sinking (VOUTL-VDD2) | VCLAMP−OUTL | | 0.8 | 1.5 | V | IN+ = High, IN− = Low, ICLAMP−OUTL = 500 mA (pulse test, tCLPmax = 10 µs) | 10 |
| Clamping Voltage, Clamp (VCLAMP-VDD2, NCD57090A/D/F) | VCLAMP−CLAMP | | 1.1 | 1.7 | V | IN+ = High, IN− = Low, ICLAMP−CLAMP = 500 mA (pulse test, tCLPmax = 10 µs) | 10 |
| IN+, IN− to Output High Propagation Delay | tPD−ON−3.3 | 40 | 60 | 90 | ns | CLOAD = 10 nF; VDD1 = VIN+ = 3.3V, VIN− = 0 V | 10 |
| IN+, IN− to Output Low Propagation Delay | tPD−OFF−3.3 | 40 | 60 | 90 | ns | CLOAD = 10 nF; VDD1 = VIN+ = 3.3 V, VIN− = 0 V | 10 |
| Propagation Delay Distortion (tPD−ON − tPD−OFF) | tDISTORT | -25 | | 25 | ns | TA = −40°C to 125°C, PW > 150 ns | 10 |
| Prop Delay Distortion between Parts | tDISTORT_TOT | -30 | 0 | 30 | ns | PW > 150 ns | 10 |
| Junction-to-Air Thermal Resistance, SOIC-8 wide body (1-layer) | RJA | | 156 | | °C/W | 1-Layer PCB, see Note 5 | 7 |
| Junction-to-Air Thermal Resistance, SOIC-8 wide body (4-layer) | RJA | | 85 | | °C/W | 4-Layer PCB, see Note 5 | 7 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | ABS | | RIO Insulation Resistance at TS, VIO = 500 V 109 Table 3. ABSOLUTE MAXIMUM RATINGS (Note 1) | 7 |
## CAD (KiCad official)
- Symbol: `NCV57090ADWR2G`
- Footprint: `Package_SO:SOIC-8_7.5x5.85mm_P1.27mm`
- 3D model: SOIC-8-300mil (KiCad packages3D, STEP)
- 3D model files: `ncv57090adwr2g-etched.step` / `ncv57090adwr2g-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ncv57090adwr2g.step` / `ncv57090adwr2g.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [onsemi datasheet](https://www.onsemi.com/pdf/datasheet/ncv57090adwr2-d.pdf) (26 pp, sha256 `26abe74476d9160c`, retrieved 2026-11-11, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ncv57090adwr2g-datasheet.pdf)