main
History Download
Ray Publish 0.1.0 1a63d5c

NCV3066DR2G

onsemi · LED Drivers · SOIC-8

NCV3066DR2G from onsemi, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 Switch Collector output Internal Darlington switch collector; the datasheet limits VSWC to −0.3 to +42 V and the switch current ISW to 1.5 A.
2 Switch Emitter output Internal Darlington switch emitter; with the transistor off, VSWE is limited to −0.6 V to VCC.
3 Timing Capacitor passive Timing capacitor pin that sets the switching frequency; the pin voltage is limited to −0.2 V to +1.4 V.
4 GND power_in Ground pin for all internal circuits; all maximum ratings are measured versus this pin.
5 Comparator Inverting Input input Inverting input of the internal comparator, rated at −0.3 V to VCC, with a threshold voltage (VTH) of 235 mV nominal.
6 VCC power_in Voltage supply; the datasheet gives an operating input range of 3.0 V to 40 V and a maximum rating of 0 to +42 V.
7 Ipk Sense input Peak current sense input that monitors the voltage drop across an external resistor, rated at −0.3 V to VCC + 0.3 V, with the current-limit threshold at 200 mV nominal.
8 ON/OFF input ON/OFF control: pulling the pin below 0.8 V or leaving it open turns the regulator off, and pulling it above 2.4 V (maximum 25 V, and below VCC) turns it on.

Key specifications

Parameter Value
Manufacturer onsemi
Package SOIC-8
Category Nixie Tube Driver/LED Driver
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Oscillator frequency fOSC 110 150 190 kHz VPin5 = 0 V, CT = 2.2 nF, TJ = 25°C 4
Discharge to charge current ratio IDISCHG/ICHG 5.5 6 6.5 - Pin 7 to VCC, TJ = 25°C 4
Current limit sense voltage VIPK(Sense) 165 200 235 mV TJ = 25°C (Note 7) 4
Darlington switch collector to emitter voltage drop VSWCE(DROP) 1 1.3 V ISW = 1.0 A, TJ = 25°C (Note 6) 4
Collector off-state current IC(OFF) 1 10 µA VCE = 40 V 4
Threshold voltage VTH -10 10 % TJ = −40°C to +125°C, tolerance of 235 mV nominal 4
Threshold voltage VTH 235 mV TJ = 25°C 4
Threshold voltage line regulation REGLINE -6 2 6 mV VCC = 3.0 V to 40 V 4
Input bias current ICII -1000 -100 1000 nA Vin = Vth 4
ON/OFF pin logic input level high VIH 2.2 V VOUT = 0 V, TJ = 25°C 4
ON/OFF pin logic input level high VIH 2.4 V VOUT = 0 V, TJ = 0°C to +85°C 4
ON/OFF pin logic input level low VIL 1 V VOUT = Nominal Output Voltage, TJ = 25°C 4
ON/OFF pin logic input level low VIL 0.8 V VOUT = Nominal Output Voltage, TJ = 0°C to +85°C 4
Supply current ICC 7 mA VCC = 5.0 V to 40 V, CT = 2.2 nF, Pin 7 = VCC, VPin5 > Vth, Pin 2 = GND 4
Standby quiescent current ISTBY 85 120 µA ON/OFF Pin = 5.0 V (OFF), TJ = 25°C 4
Standby quiescent current ISTBY 120 µA ON/OFF Pin = 5.0 V (OFF), TJ = −40°C to +125°C 4
Thermal shutdown threshold TSHD 160 °C 4
Thermal shutdown hysteresis TSHDHYS 10 °C 4
VCC supply voltage VCC 0 42 V Measured vs. Pin 4 3
Comparator inverting input voltage VCII -0.3 V Pin 5; upper limit printed as +VCC 3
Darlington switch collector voltage VSWC -0.3 42 V Pin 1, measured vs. Pin 4 3
Darlington switch emitter voltage (transistor OFF) VSWE -0.6 V Pin 2, transistor OFF; upper limit printed as +VCC 3
Darlington switch collector to emitter voltage VSWCE -0.3 42 V Pins 1-2 3
Darlington switch current ISW 1.5 A 3
Ipk sense voltage VIPK -0.3 V Pin 7; upper limit printed as VCC + 0.3 V 3
Timing capacitor pin voltage VTC -0.2 1.4 V Pin 3 3
Lead temperature soldering TSLD 260 °C 3
ON/OFF pin voltage VON/OFF -0.3 25 V Must be < VCC 3
Storage temperature range TSTG -65 150 °C 3
Maximum junction temperature TJMAX 150 °C 3
Operating junction temperature range (NCV variant) TJ -40 125 °C NCV3066 3
Input voltage range VCC 3 40 V Stated in Features section, not in a table 1
Thermal resistance junction-to-air, SOIC-8 RJA 180 °C/W SOIC-8, 35 µm copper, 10 cm² copper area (Note 5) 3

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper 4. The pins which are not defined may not be loaded by external signals. 5. 35 m copper, 10 cm2 copper area. 3

CAD (KiCad official)

  • Symbol: NCV3066DR2G
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: ncv3066dr2g-etched.step / ncv3066dr2g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncv3066dr2g.step / ncv3066dr2g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (20 pp, sha256 f3f39aff95d13b06, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF