3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownNCV3066DR2G
onsemi · LED Drivers · SOIC-8
NCV3066DR2G from onsemi, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | Switch Collector | output | Internal Darlington switch collector; the datasheet limits VSWC to −0.3 to +42 V and the switch current ISW to 1.5 A. |
| 2 | Switch Emitter | output | Internal Darlington switch emitter; with the transistor off, VSWE is limited to −0.6 V to VCC. |
| 3 | Timing Capacitor | passive | Timing capacitor pin that sets the switching frequency; the pin voltage is limited to −0.2 V to +1.4 V. |
| 4 | GND | power_in | Ground pin for all internal circuits; all maximum ratings are measured versus this pin. |
| 5 | Comparator Inverting Input | input | Inverting input of the internal comparator, rated at −0.3 V to VCC, with a threshold voltage (VTH) of 235 mV nominal. |
| 6 | VCC | power_in | Voltage supply; the datasheet gives an operating input range of 3.0 V to 40 V and a maximum rating of 0 to +42 V. |
| 7 | Ipk Sense | input | Peak current sense input that monitors the voltage drop across an external resistor, rated at −0.3 V to VCC + 0.3 V, with the current-limit threshold at 200 mV nominal. |
| 8 | ON/OFF | input | ON/OFF control: pulling the pin below 0.8 V or leaving it open turns the regulator off, and pulling it above 2.4 V (maximum 25 V, and below VCC) turns it on. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-8 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Oscillator frequency | fOSC | 110 | 150 | 190 | kHz | VPin5 = 0 V, CT = 2.2 nF, TJ = 25°C | 4 |
| Discharge to charge current ratio | IDISCHG/ICHG | 5.5 | 6 | 6.5 | - | Pin 7 to VCC, TJ = 25°C | 4 |
| Current limit sense voltage | VIPK(Sense) | 165 | 200 | 235 | mV | TJ = 25°C (Note 7) | 4 |
| Darlington switch collector to emitter voltage drop | VSWCE(DROP) | 1 | 1.3 | V | ISW = 1.0 A, TJ = 25°C (Note 6) | 4 | |
| Collector off-state current | IC(OFF) | 1 | 10 | µA | VCE = 40 V | 4 | |
| Threshold voltage | VTH | -10 | 10 | % | TJ = −40°C to +125°C, tolerance of 235 mV nominal | 4 | |
| Threshold voltage | VTH | 235 | mV | TJ = 25°C | 4 | ||
| Threshold voltage line regulation | REGLINE | -6 | 2 | 6 | mV | VCC = 3.0 V to 40 V | 4 |
| Input bias current | ICII | -1000 | -100 | 1000 | nA | Vin = Vth | 4 |
| ON/OFF pin logic input level high | VIH | 2.2 | V | VOUT = 0 V, TJ = 25°C | 4 | ||
| ON/OFF pin logic input level high | VIH | 2.4 | V | VOUT = 0 V, TJ = 0°C to +85°C | 4 | ||
| ON/OFF pin logic input level low | VIL | 1 | V | VOUT = Nominal Output Voltage, TJ = 25°C | 4 | ||
| ON/OFF pin logic input level low | VIL | 0.8 | V | VOUT = Nominal Output Voltage, TJ = 0°C to +85°C | 4 | ||
| Supply current | ICC | 7 | mA | VCC = 5.0 V to 40 V, CT = 2.2 nF, Pin 7 = VCC, VPin5 > Vth, Pin 2 = GND | 4 | ||
| Standby quiescent current | ISTBY | 85 | 120 | µA | ON/OFF Pin = 5.0 V (OFF), TJ = 25°C | 4 | |
| Standby quiescent current | ISTBY | 120 | µA | ON/OFF Pin = 5.0 V (OFF), TJ = −40°C to +125°C | 4 | ||
| Thermal shutdown threshold | TSHD | 160 | °C | 4 | |||
| Thermal shutdown hysteresis | TSHDHYS | 10 | °C | 4 | |||
| VCC supply voltage | VCC | 0 | 42 | V | Measured vs. Pin 4 | 3 | |
| Comparator inverting input voltage | VCII | -0.3 | V | Pin 5; upper limit printed as +VCC | 3 | ||
| Darlington switch collector voltage | VSWC | -0.3 | 42 | V | Pin 1, measured vs. Pin 4 | 3 | |
| Darlington switch emitter voltage (transistor OFF) | VSWE | -0.6 | V | Pin 2, transistor OFF; upper limit printed as +VCC | 3 | ||
| Darlington switch collector to emitter voltage | VSWCE | -0.3 | 42 | V | Pins 1-2 | 3 | |
| Darlington switch current | ISW | 1.5 | A | 3 | |||
| Ipk sense voltage | VIPK | -0.3 | V | Pin 7; upper limit printed as VCC + 0.3 V | 3 | ||
| Timing capacitor pin voltage | VTC | -0.2 | 1.4 | V | Pin 3 | 3 | |
| Lead temperature soldering | TSLD | 260 | °C | 3 | |||
| ON/OFF pin voltage | VON/OFF | -0.3 | 25 | V | Must be < VCC | 3 | |
| Storage temperature range | TSTG | -65 | 150 | °C | 3 | ||
| Maximum junction temperature | TJMAX | 150 | °C | 3 | |||
| Operating junction temperature range (NCV variant) | TJ | -40 | 125 | °C | NCV3066 | 3 | |
| Input voltage range | VCC | 3 | 40 | V | Stated in Features section, not in a table | 1 | |
| Thermal resistance junction-to-air, SOIC-8 | RJA | 180 | °C/W | SOIC-8, 35 µm copper, 10 cm² copper area (Note 5) | 3 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | 4. The pins which are not defined may not be loaded by external signals. 5. 35 m copper, 10 cm2 copper area. | 3 |
CAD (KiCad official)
- Symbol:
NCV3066DR2G - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
ncv3066dr2g-etched.step/ncv3066dr2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncv3066dr2g.step/ncv3066dr2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (20 pp, sha256
f3f39aff95d13b06, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).