main
History Download
Ray Publish 0.1.0 d036411

NCP81599MNTXG

onsemi · DC-DC Controllers · QFN-32-EP(5x5)

NCP81599MNTXG from onsemi, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 HSG1 output S1 gate drive; drives the S1 N-channel MOSFET with a voltage equal to VDRV superimposed on the switch node voltage VSW1.
2 LSG1 output Drives the gate of the S2 N-channel MOSFET between ground and VDRV.
3 PGND1 power_in Power ground for the low side MOSFET drivers; connect closely to the source of the bottom N-channel MOSFETs.
4 CSN1 input Negative terminal of the current sense amplifier (rated -0.3 V to 35 V).
5 CSP1 input Positive terminal of the current sense amplifier (rated -0.3 V to 35 V).
6 V1 power_in Input voltage of the converter; operating range 4.5 V to 32 V (NCV81599) or 4.5 V to 28 V (NCP81599).
7 CS1 output Current sense amplifier output that sources a current proportional to the voltage across RS1 into an external resistor; ground this pin if not used.
8 CLIND output Open drain output; high voltage indicates that the CS1 or CS2 voltage has exceeded the I2C programmed limit.
9 SDA bidirectional I2C interface data line.
10 SCL input I2C interface clock line.
11 INT output Open drain interrupt output indicating the state of the output power, the internal thermal trip, and other I2C programmable functions.
12 ADDR input I2C address pin; a resistor of less than 200 kΩ to ground sets the I2C address.
13 AGND power_in Ground pin for the analog circuitry.
14 AGND power_in Ground pin for the analog circuitry.
15 COMP output Output of the transconductance amplifier used for stability in closed loop operation.
16 EN input Logic high enables switching and logic low shuts down and resets the device; a middle level stops switching and keeps VCC alive.
17 PDRV output Open drain output used to control a PMOSFET (rated -0.3 V to 35 V).
18 CS2 output Current sense amplifier output that sources a current proportional to the voltage across RS2 into an external resistor; ground this pin if not used.
19 FB input Feedback voltage of the output, negative terminal of the gm amplifier (rated -0.3 V to 5.5 V).
20 CSN2 input Negative terminal of the current sense amplifier (rated -0.3 V to 35 V).
21 CSP2 input Positive terminal of the current sense amplifier (rated -0.3 V to 35 V).
22 PGND2 power_in Power ground for the low side MOSFET drivers; connect closely to the source of the bottom N-channel MOSFETs.
23 LSG2 output Drives the gate of the S3 N-channel MOSFET between ground and VDRV.
24 HSG2 output S4 gate drive; drives the S4 N-channel MOSFET with a voltage equal to VDRV superimposed on the switch node voltage VSW2.
25 BST2 passive Bootstrapped driver supply swinging from a forward drop below VDRV up to a forward drop below VOUT + VDRV; place a 0.1 µF capacitor to VSW2.
26 VSW2 passive Switch node that swings from a diode voltage drop below ground up to the output voltage.
27 V2 input Output voltage of the converter; connect to the output externally for OVLO sense.
28 VCCD power_in Internal digital power supply input (4.5 V to 5.5 V); always connect to VCC and decouple with a 1 µF capacitor close to the part.
29 VDRV power_in Internal voltage supply to the driver circuits (4.5 V to 5.5 V); decouple with a 1 µF capacitor close to the part.
30 VCC power_out Output of a linear regulator powered from V1 that supplies the internal circuitry; decouple with a 1 µF capacitor.
31 VSW1 passive Switch node that swings from a diode voltage drop below ground up to V1.
32 BST1 passive Bootstrapped driver supply swinging from a forward drop below VDRV up to a forward drop below V1 + VDRV; place a 0.1 µF capacitor to VSW1.
33 THPAD power_in Center thermal pad; connect to AGND externally.

Key specifications

Parameter Value
Manufacturer onsemi
Package QFN-32-EP(5x5)
Category Power Supply Chip
Pins 33

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Voltage VCCD VCCD -0.3 5.5 V 5
Address Pin Output Voltage ADDR -0.3 5.5 V 5
Driver Input Voltage VDRV -0.3 5.5 V 5
Internal Regulator Output VCC -0.3 5.5 V 5
Output of Current Sense Amplifiers CS1, CS2 -0.3 5.5 V 5
Enable Input EN -0.3 5.5 V 5
Feedback Voltage FB -0.3 5.5 V 5
V1 Power Stage Input Voltage V1 -0.3 35 V 40 V (20 ns) 5
Positive and Negative Current Sense CSP1, CSN1, CSP2, CSN2 -0.3 35 V 40 V (20 ns) 5
Low Side Driver LSG1, LSG2 -0.3 5.5 V 5
PMOSFET Driver PDRV -0.3 35 V 40 V (20 ns) 5
Voltage Differential AGND to PGND AGND-PGND -0.3 0.3 V 5
CSP-CSN Differential Voltage CS1DIF, CS2DIF -0.5 0.5 V 5
PDRV Maximum Current PDRVI 0 10 mA 5
PDRV Maximum Pulse Current PDRVIPUL 0 200 mA 100 ms on time, with > 1 s interval 5
Operating Junction Temperature Range TJ -40 150 °C 5
Operating Ambient Temperature Range TA -40 125 °C 5
Storage Temperature Range TSTG -55 150 °C 5
Lead Temperature Soldering Reflow (Pb-Free) RF 260 °C Peak 5
Maximum Power Dissipation PD 4.1 W TA = 25°C 5
Maximum Power Dissipation PD 2.1 W TA = 85°C 5
Thermal Resistance Junction-to-Air with Solder RJA 30 °C/W 5
Thermal Resistance Junction-to-Case Top with Solder RJCT 1.7 °C/W 5
Thermal Resistance Junction-to-Case Bottom with Solder RJCB 2 °C/W 5
V1 Operating Input Voltage (NCP81599) V1 4.5 28 V 6
VDRV Operating Input Voltage VDRV 4.5 5 5.5 V 6
VCCD Operating Input Voltage VCCD 4.5 5.5 V 6
VCC UVLO Rising Threshold VCCRISE 4.21 4.27 4.35 V 6
VCC UVLO Falling Threshold VCCFALL 3.9 3.96 4.06 V 6
VDRV UVLO Rising Threshold VDRVRISE 4.21 4.31 4.35 V 6
VDRV UVLO Falling Threshold VDRVFALL 3.9 4.01 4.06 V 6
VCC Output Voltage VCC 4.5 5 V With no external load 6
VCC Output Current Limit IOUTVCC 80 97 mA VCC Loaded to 4.3 V, EN > 0.8 V 6
V1 Shutdown Supply Current IVCC_SD 15 A EN < 0.4 V, V1 = 12 V 6
V1 Normal Current IV1 7.3 mA 0.8 V < EN < 1.88 V, 4.5 V ≤ V1 ≤ 32 V, (No Switching) 6
VCCD Standby Current IVCCD 4 mA 0.8 V < EN < 1.88 V 6
VCCD Switching Current IVCCD_SW 4.1 mA EN > 2.2 V 6
VDRIVE Switching Current Buck IV1_SW 16 mA EN = 5 V, Cgate = 2.2 nF, VSW = 0 V, FSW = 600 kHz 6
VDRIVE Switching Current Boost IV1_SW 15 mA EN = 5 V, Cgate = 2.2 nF, VSW = 0 V, FSW = 600 kHz 6
Voltage Output Accuracy FB FB 0.495 0.5 0.505 V DAC_TARGET = 00110010 6
Voltage Output Accuracy FB FB 1.188 1.2 1.212 V DAC_TARGET = 01111000 6
Voltage Output Accuracy FB FB 1.98 2 2.02 V DAC_TARGET = 11001000 6
Voltage Accuracy Over Temperature VOUTERT -1 1 % VFB ≥ 0.5 V 6
Voltage Accuracy Over Temperature VOUTERT -5 5 mV VFB < 0.5 V 6
Voltage Accuracy VOUTER -0.45 0.45 % TA = 25°C, VFB ≥ 0.5 V 6
Pass FET Reverse Leakage Current from BST to VDRV IBST 0.05 1 A DIL BST = 32 V, TA = 25°C 6
BST-VSW UVLO Falling BST_UVLO 3.2 3.5 3.8 V BST_UVLO Falling 6
BST-VSW UVLO Rising BST_UVLO 3.4 3.7 4.1 V BST_UVLO Rising 6
Oscillator Frequency FSW_0 552 600 648 kHz FSW = 000, default 7
Oscillator Frequency Accuracy FSWE -12 12 % 7
Minimum On Time MOT 100 ns Measured at 10% to 90% of VCC 7
Minimum Off Time MOFT 100 ns Measured at 90% to 10% of VCC 7
Interrupt Low Voltage VINTI 0.2 V IINT(sink) = 2 mA 7
Transconductance Deviation CSGE -30 30 % CSPx−CSNx = 10 mV 7
Transconductance Deviation CSGE -20 20 % CSPx−CSNx = 25 mV to 100 mV 7
Input Current Sense Common Mode Range CSCMMR_I 4.5 32 V CSP1 is tied to V1 7
Output Current Sense Common Mode Range CSCMMR_O 4 25.5 V 7
Current Limit Indicator Output Low CLINDL 100 mV Input current = 500 µA 7
Internal Current Sense Gain for PWM ICG 9.4 10 10.5 V/V CSPx−CSNx = 25 mV 7

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper Vsw1/2 trace to high−side MOSFET source pin instead of copper pour area. The controller should be placed 30

CAD (KiCad official)

  • Symbol: NCP81599MNTXG
  • Footprint: Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm
  • 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: ncp81599mntxg-etched.step / ncp81599mntxg-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncp81599mntxg.step / ncp81599mntxg.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (33 pp, sha256 a2417a587d3528d6, retrieved 2026-11-09, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF