3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownNCP1593AMNTWG
onsemi · DC-DC Converters · DFN-10-EP(3x3)
NCP1593AMNTWG from onsemi, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connect on the NCP1593A. May be left floating or tied to GND. (On NCP1593B this pin is an additional LX.) |
| 2 | LX | power_out | Switching node - drain of the internal high-side PMOS and low-side NMOS. Connect the output inductor to this pin (tie pins 2 and 3 together). |
| 3 | LX | power_out | Switching node - drain of the internal high-side PMOS and low-side NMOS. Connect the output inductor to this pin (tie pins 2 and 3 together). |
| 4 | PG | output | Power Good - open-drain output from the Power-Good comparator. High-impedance when FB voltage is within regulation (rising threshold 0.54 V typ, falling 0.51 V typ); otherwise pulled low (VRPG ≈ 130 mV at 2.5 mA). |
| 5 | EN | input | Enable input. Logic high (>1.4 V) turns the part on; logic low (<0.4 V) shuts it off. An internal ~1.4 µA pull-up forces the part into the enabled state when the pin is left floating. |
| 6 | FB | input | Feedback input to the error amplifier. Connect a resistor divider from VOUT to this pin to program the regulated output; internal reference VFB ≈ 0.6 V. |
| 7 | SS | passive | Soft-start. An external capacitor to GND sets the soft-start ramp time (charged by ISS ≈ 0.7 µA). Leaving the pin open uses the default 500 µs internal soft-start. (On NCP1593B this pin is NC and must be left floating.) |
| 8 | VCCA | power_in | Analog/internal-bias supply input (called VCC in the pin table, VCCA in the pin-connection diagram and application circuit). Bypass with a 0.1 µF ceramic capacitor to GND and tie directly to VCCP on the board. Range 4.0 V to 5.5 V. |
| 9 | VCCP | power_in | Power-stage supply input for the internal high-side PMOS. Tie to VCCA and bypass with input capacitance. Range 4.0 V to 5.5 V. |
| 10 | VCCP | power_in | Power-stage supply input for the internal high-side PMOS. Tie to VCCA and bypass with input capacitance. Range 4.0 V to 5.5 V. |
| EP | GND | power_in | Exposed thermal pad - device ground and primary thermal path. Must be soldered to the PCB ground plane for proper electrical and thermal operation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | DFN-10-EP(3x3) |
| Category | Power Management (PMIC) |
| Pins | 11 |
Ordering variants
Same part, different packaging or reel option.
NCP1593AMNTWGNCP1593AMNTWGBMNTWG
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Range | VIN | 4 | 5.5 | V | 4 | ||
| VCC UVLO Threshold | VUVLO | 2.4 | 2.5 | 2.9 | V | 4 | |
| VCC Quiescent Current | IINVCC | 1 | 1.5 | mA | 4 | ||
| VCCP Quiescent Current | IINVCCP | 20 | 50 | µA | 4 | ||
| Shutdown Supply Current | IQSHDN | 1.8 | 3 | µA | 4 | ||
| Reference Voltage | VFB | 0.591 | 0.6 | 0.609 | V | 4 | |
| Reference Voltage | VFB | 0.594 | 0.6 | 0.606 | V | TJ = 25°C | 4 |
| Feedback Input Bias Current | IFB | 10 | 100 | nA | 4 | ||
| Switching Frequency | fSW | 0.87 | 1 | 1.13 | MHz | 4 | |
| High-Side MOSFET On Resistance | RDSonH | 90 | 190 | mΩ | IDS = 100 mA, VIN = 5.0 V | 4 | |
| Low-Side MOSFET On Resistance | RDSonL | 60 | 90 | mΩ | IDS = 100 mA, VIN = 5.0 V | 4 | |
| Power Good Rising Threshold | VPGH | 0.51 | 0.54 | V | 4 | ||
| Power Good Falling Threshold | VPHL | 0.48 | 0.51 | V | 4 | ||
| Power Good Pulldown Voltage | VRPG | 130 | 250 | mV | IPG = 2.5 mA | 4 | |
| Enable Pullup Current | IEN | 1.4 | 3 | µA | 4 | ||
| Default Soft-start Ramp Time | tSS | 0.5 | 0.58 | 0.65 | ms | SS = open; fSW = 1MHz | 4 |
| Soft-start Current | ISS | 0.51 | 0.7 | 0.87 | A | 4 | |
| Input supply pin (pins 8, 9, 10) to GND | Vin | -0.3 | 6.5 | V | DC | 3 | |
| Input supply pin (pins 8, 9, 10) to GND, transient | Vin | -1 | V | t < 100 ns | 3 | ||
| LX to GND | -0.7 | V | DC | 3 | |||
| LX to GND, transient | -5 | V | t < 100 ns | 3 | |||
| All other pins to GND | -0.3 | 6 | V | DC | 3 | ||
| All other pins to GND, transient | -1 | V | t < 100 ns | 3 | |||
| Operating Ambient Temperature Range | TA | -40 | 85 | °C | 3 | ||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | 3 | ||
| Maximum Junction Temperature | TJ(MAX) | 150 | °C | 3 | |||
| Storage Temperature Range | TS | -55 | 150 | °C | 3 | ||
| Thermal Resistance Junction-to-Air | RJA | 68 | °C/W | Note 2: 1x1 inch sq. 1 oz. Cu FR-4 or G-10 board | 3 |
CAD (KiCad official)
- Symbol:
NCP1593AMNTWG - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
ncp1593amntwg-etched.step/ncp1593amntwg-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncp1593amntwg.step/ncp1593amntwg.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (14 pp, sha256
e51c579bf424fdbd, retrieved 2026-08-17, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).